Overcurrent monitor operates up to 26V

Using a current-sense amplifier, a high-side MOSFET driver, and a latching voltage monitor a circuit can be easily constructed that protects from overcurrent conditions and operates at voltages as high as 26V.

Powering Xilinx Zynq 7000 Series SoC/FPGA Evaluation Module with Single Power Management IC

This TPS65218-based reference design is a compact integrated power solution for the Xilinx® Zynq® 7010 SoC/FPGA (part of the Zynq® 7000 product family). This design shows the TPS65218 as an all-in-one PMIC used to provide the five power rails required to power the Zynq® 7010 SoC/FPGA. The TPS65218, including passive components, requires only 1.594 in ² of total board area to provide five power rails to the Zynq® 7010 . TPS65218 has the flexibility to support DDR3L or DDR3 memory. This power management IC can be powered from a single 5V supply or a single Li-ion battery. This design is guaranteed to operate over the entire industrial temperature range (-40°C to 105°C).

Schematic PCB

DER-815 - 45W 24V output isolated flyback power supply for smart speakers and tubular motors based on InnoSwitch3-CP

Schematic PCB

DER-903 - 72 W charger using InnoSwitch3-CP with PowiGaN technology, 93% efficiency

72 W isolated flyback power supply for chargers and adapters using PowiGaN-based InnoSwitch3-CP (INN3279CH215)

Schematic PCB

MAXREFDES145#: 8-channel IO-Link master

The MAXREFDES145# is a fully IO-Link®-compliant, 8-port IO-Link master reference design. This design uses TEConcept's IO-Link master stack and is both an IO-Link master reference design as well as an IO-Link sensor /actuator development and test system. Eight IO-Link ports allow for simultaneous testing of up to eight different sensors (or actuators).

Schematic PCB

SJA1105Q-EVB: Ethernet switch and PHY evaluation board.

The SJA1105Q-EVB is an evaluation board for the SJA1105P/Q/R/S Automotive Ethernet switchs series and TJA1102 dual 100BASE-T1 PHY.

DER-748 - 45W Selectable Output Voltage USB Power Supply for InnoSwitch3-CP with PowiGaN Technology (INN3279C-H222

Schematic PCB

Envelope tracking power supply reference design for audio power amplifiers

This envelope tracking power supply reference design helps extend battery life in portable audio applications such as Bluetooth® or Wi-Fi speakers. The low-power buck converter in this design features envelope tracking for audio power amplifiers, maintaining high efficiency over the output voltage range. By adding an audio envelope signal to the FB pin of TI's TPS61178 device, the output voltage can change according to the envelope of the audio signal, thereby dynamically adapting to the power supply of the TPA3128D2 power amplifier and optimizing its power consumption.

Schematic PCB

Automotive 2MHz Class D 4-channel 21W audio amplifier reference design in Class AB form factor

The TIDA-00743 reference design is a small module designed to evaluate a digital input Class D audio amplifier in a system dedicated to the classic Class AB audio power amplifier module. This design demonstrates the power loss reduction that a Class D amplifier can achieve. This design demonstrates how the 2.1MHz operation of the TAS6424-Q1 enables a compact power amplifier solution.

Schematic PCB

TJA1100HN 100BASE-T1 Automotive Ethernet PHY - Customer Evaluation Board

The OM14500/TJA1100 is designed for rapid evaluation of the TJA1100HN PHY. It has direct access to MDI and MII/RMII interfaces and chip configuration bits

Schematic PCB

OM14510-SJA1105TJP: Automotive Ethernet switch application board

OM14510/SJA1105TJP is an application board used to evaluate SJA1105EL and SJA1105TEL

Schematic PCB

CN0256

Isolated LVDS interface circuit

Schematic PCB

Lakewood (MAXREFDES7#): 3.3V input, ±12V (±15V) output isolated power supply

This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low dropout (LDO) linear regulators. Test results and hardware files are included.

Schematic PCB

12Gbps multi-channel BERT board reference design

This reference design is a 12Gbps low-cost bit error tester (BERT) that generates and checks up to 8 channels of pseudo-random binary sequences (PRBS). This proven design provides a convenient way to generate multi-lane high-speed serial bit streams up to 12Gbps and inspect the incoming serial bit stream for bit errors. This design can be used as a handheld BERT to evaluate the signal integrity and bit error performance of high-speed subsystems.

Schematic PCB

CN0337

带三线式补偿的12位、300 kSPS、单电源、完全隔离式RTD温度测量系统

Schematic PCB

Corona (MAXREFDES12#): Isolated, eight-channel, industrial digital input level translator/serializer

This document explains how the Corona (MAXREFDES12#) subsystem reference design provides a compact and simple isolated digital input interface for industrial control and automation applications. Hardware and firmware design files are provided.

Schematic PCB

CN0278

Complete 4 mA to 20 mA HART solution with additional voltage output capability

Schematic PCB

750W AC-DC Reference Design

Microchip’s 750W AC-DC Reference Design demonstrates a semi-bridgeless PFC topology followed by a peak current controlled zero-voltage switching full-bridge (ZVS FB) converter with digital slope compensation to achieve very high conversion efficiencies. This power supply can be firmware updated (including the compensator algorithm) with zero down time to the system it is powering while the

Schematic PCB

DER-717 - InnoSwitch3-CE based 15 W adapter with ±30 kV ESD capability

15 W isolated flyback power supply using InnoSwitch3-CE (INN3164C-H101) with ±30 kV ESD Capability

Schematic PCB

CN0336

12-bit, 300 kSPS, single supply, fully isolated data acquisition system for 4-20 mA input

Schematic PCB