FRDM-MC12XSF: Freedom HW for MC12XSF and MC12XS6 series

This freedom board covers MC12XSF and MC12XS6 families and ease its usage thanks to its quick evaluation tolls (Spigen or KDS) with different Kinetis MCU.

Schematic PCB

AzureWave Wi-Fi Evaluation Kit: AW-NM191-uSD

Automotive dual-channel SiC MOSFET gate driver reference design with two-level shutdown protection

This reference design is an automotive-qualified isolated gate driver solution that drives silicon carbide (SiC) MOSFETs in a half-bridge configuration. This design provides two push-pull bias supplies for dual-channel isolated gate drivers, each providing +15V and –4V output voltages and 1W output power. The gate driver is capable of 4A peak source current and 6A peak sink current. The driver implements reinforced isolation and can withstand 8kV peak isolation voltage and 5.7kV RMS isolation voltage as well as common-mode transient immunity (CMTI) of over 100V/ns. This reference design includes a two-stage shutdown circuit that protects the MOSFET against voltage overshoot during short circuit conditions. DESAT detection threshold and second stage shutdown delay time are configurable. This design uses an ISO7721-Q1 digital isolator to connect the fault and reset signals. The overall design adopts a compact double-layer PCB board of 40mm × 40mm.

Schematic PCB

Loop-powered 4mA to 20mA RTD Temperature Transmitter Reference Design with MSP430 Smart Analog Combo

This TI reference design provides a low-component-count, low-cost solution for a 4 to 20mA loop-powered resistance temperature detector (RTD) temperature transmitter. The design utilizes the on-chip smart analog combination module in the MSP430FR2355 MCU to control the loop current, thus eliminating the need for a separate DAC. The design achieves 12-bit output resolution and 6µA output current resolution. The design incorporates reverse polarity protection as well as IEC61000-4-2 and IEC61000-4-4 protection on the loop power input.

Schematic PCB

1kW Full-Bridge DC-DC Converter

This reference design provides design guidelines, data, and more for a 1kW server power supply using a phase-shifted full-bridge DC-DC converter.

Schematic PCB

Phase-shifted full bridge (PSFB) AC-DC power supply basic simulation circuit

12V and 24V brushless DC external rotary motor reference design

This 6cm motor is packaged and ready; connect to power and run! The simple and reliable design is easily modified to support speed and current system needs. The DRV5013 Hall-effect sensor senses the magnetic rotor position, and the DRV8307 controller determines when to drive the CSD88537ND FET that energizes the coil .

Schematic PCB

Designing a buck-boost LED driver using the MAX16834

This reference design is for a buck-boost LED driver. The MAX16834 current-mode high-brightness LED driver is featured, and the MAX16834 EV (evaluation) kit is used to implement the design. The application note shows the design specifications, schematic, bill of materials (BOM), and performance data.

CN0290

Extending the low-frequency range of high-performance phase-locked loops

Schematic PCB

CN0240

Bidirectional Isolated High-End Current Sense Module with 270 V Common-Mode Rejection

Schematic PCB

15-Cell Li-Ion Battery Controller Analog Front-End Reference Design

The TIDA00255 reference design utilizes the bq76940 analog front end (AFE) IC. It can measure battery voltage, mold temperature or external thermistor voltage using a 14-bit ADC. Current is measured individually by a separate 16-bit coulomb counter. The design turns off the low-side power FET to stop discharging or charging based on selected hardware limits. A microcontroller not included in this design will be part of the battery controller to communicate with the AFE to set protection thresholds, enable the power FETs, provide fault recovery, and shut down the FETs during over/under temperature conditions. Battery controller designs may include additional features that are not part of this reference design, such as secondary overvoltage protection, measurement, and isolated communications to inform the system of battery status.

Schematic PCB

Sub-1GHz and 2.4GHz Antenna Reference Designs

This antenna board reference design contains multiple low-cost antenna solutions for sub-1 GHz and 2.4 GHz short-range wireless systems.

Schematic PCB

Acontis EtherCAT Master Protocol Stack Reference Design

The Acontis EC-Master EtherCAT Master stack is a highly portable software stack that can be used on a variety of embedded platforms. EC-Master supports high-performance TI Sitara MPUs and provides an advanced EtherCAT Master solution that customers can use to implement EtherCAT communication interface boards, EtherCAT-based PLCs or motion control applications. The EC-Master architecture is designed so that users do not need to plan additional tasks, so the full stack functionality is available even on platforms without an operating system (such as TI Starterware supported on AM335x). This architecture combined with high-speed Ethernet drivers allows users to implement EtherCAT master on the Sitara platform with very short cycle times of 100 microseconds or less.

Schematic PCB

MAXREFDES27#: IO-LINK proximity detection light sensor

Maxim's MAXREFDES27# reference design is a tiny, low-power IO-Link ^® optical proximity sensor compliant with IEC 61131-9. It contains an infrared (IR) receiver, matching IR LED driver, IO-Link transceiver, and efficient step-down converter. The entire design fits on an 8.2mm x 31.5mm printed circuit (PC) board.

Schematic PCB

FRDM33771BTPLEVB: MC33771 evaluation board with isolated daisy chain communication

24V dual-channel brushless DC motor driver reference design for dishwasher water pumps

TIDA-00447 is a 24V, dual brushless DC (BLDC) motor drive reference design that can be used to drive circulating water pumps and drain pumps in dishwashers. The circulating water pump and drainage pump drive stages are designed for continuous operation of 100W and 30W respectively. The drain pump driver is based on a single-chip, low external component count three-phase motor driver with integrated power MOSFETs and provides a proprietary sensorless control scheme enabling continuous sine wave drive. In addition, it features an integrated buck/linear regulator that efficiently reduces the supply voltage to 5V or 3.3V to power internal and external circuitry. The circulating water pump is implemented using a discrete solution with MCU, external MOSFET driver with protection mechanism and current sensing function, and external power MOSFET. This architecture allows the flexibility to adjust drive power levels as needed. The MCU is programmed through the InstaSPIN-BLDC software, which enables sensorless trapezoidal control of the BLDC motor using an anti-EMF integration approach, and can also be used to configure and control the speed of the drainage pump stage. A separate UART interface allows the drive unit to communicate with the main user interface controller. This reference design has been fully tested with current and motor stop protection mechanisms operating at full load.

Schematic PCB

JN5169XK010: ZigBee Universal Node Extension Kit

1200W switching power supply design schematic diagram and PCB design information

Schematic PCB

DER-879 - 10W isolated flyback power supply, using LinkSwitch-TNZ to generate AC zero-crossing signal and X capacitor discharge losslessly

10 W isolated flyback power supply with lossless generation of AC zero-crossing signal and X capacitor discharge using LinkSwitch-TNZ (LNK3317D)

Schematic PCB

MAXREFDES1051: 18V to 36V input, 24V/2A output, active-clamped forward isolated power supply

The MAX17599 low IQ active clamp current mode pulsewidth modulation (PWM) controller contains all the control circuitry required for the design of isolated forward converter power supplies. The MAX17599 is optimized for low-voltage industrial (4.5VDC to 36VDC) power supply applications.