Training

Location:Training / Embedded Development / FPGA / AXI High-Speed Bus / How to design FPGA scientifically: Timing constraint basics, understanding timing analysis models

You can log in to your eeworld account to continue watching：
How to design FPGA scientifically: Timing constraint basics, understanding timing analysis models
Login

Chapter 1：How to use digital electronics thinking to scientifically design FPGA
Chapter 2：How to scientifically design the logic level of FPGA RTL code
Chapter 3：How to scientifically design FPGA series: Xilinx reset mechanism and cross-clock domain processing
Chapter 4：How to design FPGA scientifically: Timing constraint basics, understanding timing analysis models
Chapter 5：How to scientifically design FPGA timing constraints and analysis in VIVADO and advanced techniques
Chapter 6：How to design FPGA scientifically: AXI interpretation of achieving AXI bus freedom
Chapter 7：How to scientifically design FPGA and write AXI bus interface from scratch
Chapter 8：How to design FPGA scientifically? Follow-up of AXI tearing by hand, self-write AXI interface simulation verification
Chapter 9：How to scientifically design the logic level of FPGA RTL code
Chapter 10：How to design FPGA scientifically: Timing constraint basics, understanding timing analysis models
Chapter 11：How to scientifically design FPGA series: Quickly tearing AXI slave SLAVE including ram code construction
Chapter 12：How to scientifically design FPGA series: GT transceiver GTX GTH S of Xilinx FPGA
Chapter 13：How to scientifically design FPGA series: Use and simulate GTX GT of Xilinx FPGA GT transceiver

Duration：25 minutes and 57 seconds
Date：2024/12/22

Uploader：MartinFowler

Introduction

keywords： FPGA AXI

How to Scientifically Design FPGA-AXI High-Speed Bus

You Might Like

Recommended Posts

2440+7113, camera problem: I use 2440+7113, ce system. Originally, the iic read and write address of 7113 should be 4a/4b, but I failed to operate 7113 with these two ports. The manual of 7113 says that if RTS0 is grounded with; zhangrenbai Embedded System

Let's learn PIC microcontroller 4 (independent keyboard control relay switch): Hello everyone, I am a novice in PIC microcontrollers, but I am very hardworking. I bought the ND118-877APIC experimental development board, which has examples but no source code. I wrote the code mys; youmurensha Microchip MCU

Humbly seek advice on the problems in Wang Aiying's "Computer Organization and Structure": Wang Aiying's "Computer Organization and Structure" Chapter 2 Exercise 2: Full adder can be composed of XOR gates and carry logic circuits. According to A XOR B = No A XOR No B, we can design an adder; fuhognquan Embedded System

Using RTC (STM32) to make a perpetual calendar: 1. Initialize the system clock after power-on2. Configure RTC2.1 Enable the clocks of PWR and BKP modules2.2 Enable access to the backup area3. Check the predefined mark to determine whether the RTC h; yhphxj stm32/stm8

msp430 real-time clock general program code: msp430 real-time clock general program code; Aguilera Microcontroller MCU

Fundamentals of Electronic Circuits: Crystal Oscillator Circuit Design Schemes and Suggestions (Transferred): [i=s]This post was last edited by qwqwqw2088 on 2015-4-29 15:12[/i] [color=#a0522d][font=Arial,] This article will discuss the crystal oscillator[/font][font=Arial, Microsoft YaHei, Microsoft YaHei, S; qwqwqw2088 Analogue and Mixed Signal

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号