With over 135 years of experience, more than 50 industrial sites and 18 R&D centers in 35 countries, Mersen Electrical Power is a global expert in power and advanced materials for high-tech industries. They offer a broad portfolio of electrical protection and control products and provide solutions for power management applications. The Mersen team works with customers around the world to design and deliver custom solutions and essential products for the commercial, industrial, renewable energy, power electronics and electric vehicle markets. Mersen's mission is to make its customers' applications safer and more reliable.
[i=s] This post was last edited by damiaa on 2017-10-16 09:28 [/i] [size=2] CH554 Review] The third article tests the timer [/size][size=2] [/size] [size=2] The timer is a necessity for microcontrolle...
In common electrical experiments and various motor tests, power is an important physical quantity, and the correct use of a power meter is a basic skill. In actual use, the range and wiring are the ke...
Reprinted from: deyisupport As discussed in previous articles in this voltage reference series, it is simple and direct to generate DC current of any magnitude using op amp feedback and a voltage refe...
As shown in Figure 1, there are several basic structures of sense amplifiers. Differential amplifiers are often used in the design of CMOS memory readout amplifier units, such as SRAM, DRAM, etc., bec...
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
I have read the source code of mbed these days, and the interface encapsulation for upper-level application calls is quite good. The code quality is relatively high, the comments are also very detai...[Details]
CMSIS Driver has similar API functions and similar calling methods. It is a further encapsulation based on the ST HAL library. It is much more convenient and simpler to use and configure than the ST ...[Details]
I used STM32CubeMX V4.22.1 to generate a project including EHT and Lwip. The debugging has been abnormal. After careful inspection, the following problems were found: 1. The hardware uses LAN8720A, b...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
This program uses the eight-channel ADC single acquisition mode. According to the configuration, ADC12SC will automatically reset after the conversion is completed in the single mode, so it is necess...[Details]
As shown in the figure, the author soldered a STM32F207VET6 board using a TQFP (32-100PIN) 0.55MM to direct plug adapter board. The board leads out the SWD debug interface (only PA13 and PA14 are occ...[Details]
1. Common knowledge about DMA. 1. Function: to achieve high-speed data transmission between chips. That is, it can achieve data transmission without occupying the CPU. 2. Mode: There are three tran...[Details]
An easy programming question for microcontrollers! Urgent, write a 3-byte binary subtraction subroutine. When using the main program to call multiple groups of data for debugging, two situations need...[Details]
One addend is in the on-chip RAM 40H, 41H, 42H units, the other addend is in the on-chip RAM 43H, 44H, 45H, and the sum is stored in the 50H, 51H, 52H units, with the carry bit stored in 00H. Please ...[Details]
Single-chip microcomputer experiment design: It is required to use 8951 series single-chip microcomputer, design a pulse generator with a pulse width duty cycle of 50%, 25% adjustable, and a period o...[Details]
Title: Use two dynamic digital tubes to display from 0 to 60, output from the P1 port of 89C51, without adding a decoder, and directly connect the digital tubes. Note that they are dynamic digital tu...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
