Huawei RF Basic Knowledge Training

Schematic PCB

ARG008A Application Principle Reference

Schematic PCB

RL-SM02BD-8723BS peripheral application circuit reference design

Schematic PCB

Solutions based on nRF24L01P RF transceiver

Schematic PCB

RTL8822CS Module Hardware Reference Design Guide

Schematic PCB

GigaDevice GDM_WIFI_01 Embedded Wi-Fi Module Solution

Schematic PCB

A low-profile version of full-featured software radio based on Raspberry Pi Pico (fully open source + detailed explanation)

With just a Raspberry Pi Pico, an analog switch and an op amp, you can build a powerful SDR receiver covering the LW, MW and SW bands. Capable of receiving signals from halfway around the world.

Schematic PCB

KW38 +20dBm Extended Range Reference Design Board

Schematic PCB

5G

RX5808 receiver ESP32 version

The hardware design adopts upper and lower layer design. The upper layer is the control circuit and the lower layer is the dual receiving circuit. The interface design is based on LVGL.

Schematic PCB

Software and hardware open source portable monitor CatSniffer (schematic diagram, PCB, source code, etc.)

This board is a Swiss Army Knife for IoT security researchers, developers, and enthusiasts. The board can be used with different types of software, including third-party sniffers such as SmartRF Packet Sniffer, Sniffle, zigbee2mqtt, Z-Stack-firmware, Ubiqua Protocol Analyzer, our custom firmware, or you can even Specific software requires writing your own software.

Schematic PCB

CaribouLite RPi HAT: Fully open source dual-channel SDR Raspberry Pi HAT with tuning range up to 6 GHz (schematic, PCB, source code, etc.)

CaribouLite is an affordable open source dual-channel software-defined radio (SDR) platform and an SDR-focused FPGA development framework implemented as a Raspberry Pi (RPi) HAT. CaribouLite turns your Raspberry Pi single-board computer (SBC) into a standalone dual-channel radio Tx/Rx with a tunable spectrum up to 6 GHz. CaribouLite gives you complete control over its hardware, including FPGA, firmware, and all supporting software. With the deeply integrated IceStorm toolchain, writing your own FPGA applications couldn't be easier. You can reuse many Verilog modules, such as the SPI and SMI modules, to support custom applications for CaribouLite hardware.

Schematic PCB

MAXREFDES161#: Frequency Synthesizer Shield

MAXREFDES161# is a high-performance frequency synthesizer capable of generating frequencies from 23.5MHz to 6GHz

Schematic PCB

ZigBee Wi-Fi Ethernet Gateway Reference Design Using EM3588

ZigBee Wi-Fi Ethernet Gateway Reference Design Using EM3588

Schematic PCB

2.4GHz ZigBee IEEE 802.15.4 based radio transceiver solution (RFMD RF6505/6575/6555)

The reference design demonstrates a complete 2.4GHz ZigBee IEEE 802.15.4 based compliant radio transceiver solutions and conform to FCC CFR47 part 15. The wireless SoC reference design series (RFMDs RF6505/6575/6555) are developed by the partnership between RFMD and Corporation. The RFMD device increases transmit power and sensitivity.

Schematic PCB

AT86RF231 PCB Antenna Diversity Reference Design

This reference design demonstrates a full-function network node with the AT86RF231 radio transceiver, which is capable of hosting a MAC layer implementation. Two ceramic chip antennas increase the link budget in a typical indoor scenario with multi-path fading effects.

Schematic PCB

QorIQ ^® T2080 Reference Design Board

The QorIQ ^® T2080 Reference Design Board (T2080RDB) is a highly integrated tool that contains the QorIQ T2080 communications processor.

Schematic PCB

LS1043A Residential Gateway Reference Design

OpenWRT Residential Gateway Home Router Platform.

Schematic PCB