A versatile LiDAR SLAM package. Supports various types of LiDAR sensors (mechanical, solid-state, etc.), 6-axis and 9-axis IMU, loose coupling and tight coupling, mapping and positioning, loop detection, etc.
The NXP® MPC5606E MCU is a gateway system built on Power Architecture® technology designed to move data from disparate sources over Ethernet.
The ESPboy CC1101 chip module allows you to detect Sub1Ghz signals (300-348MHz, 387-464MHz, 779-928MHz). Scan, decode, store to open garage doors, obstacles, IoT sensors...
The SABER board for smart devices is based on the i.MX 6SoloX processor and supports 4-core processing, low-power multimedia and graphics applications.
The MTRCKTSBN5604P motor control development kit is ideal for sensorless applications requiring one BLDC motor, such as HVAC or electric pumps.
The author specially bought a laptop motherboard, and then DIYed the peripherals and casing. The overall effect is quite beautiful.
NXP MEK provides a platform for evaluation and development of the i.MX 8X series of application processors based on Arm Cortex A35 + Cortex-M4F.
NXP's OM2385/SF001 development kit for SIGFOX applications, including OL2385 and Kinetis KL43 series MCUs for host applications
The Bidirectional 400V-12V DC/DC Converter Reference Design implements an isolated bidirectional DC/DC converter based on a microcontroller. The phase-shifted full bridge (PSFB) with synchronous rectification controls the power flow from the 400V bus/battery to the 12V battery in buck mode, while the push-pull stage controls the reverse power flow from the low-voltage battery to the high-voltage bus/battery in boost mode. . This implementation uses a Texas Instruments (TI) 32-bit microcontroller TMS320F28035 on the low-voltage side to achieve closed-loop control of bidirectional power flow. This digital controller system implements advanced control strategies to optimally control power stages under varying conditions and provides system-level intelligence for safe and seamless transitions between operating and PWM switching modes.
OpenWRT Residential Gateway Home Router Platform.
This reference design is a 2cm x 2cm RGB LED animation solution for battery powered applications using the LP5523 and MSP430FR2111 devices. The LP5523 device is an LED driver with a programmable control engine in a DSBGA package. The LP5523 provides realistic lighting patterns for applications that must fit on extremely small PCBs. The design demonstrates full functionality while using limited MCU resources.
This board is a Swiss Army Knife for IoT security researchers, developers, and enthusiasts. The board can be used with different types of software, including third-party sniffers such as SmartRF Packet Sniffer, Sniffle, zigbee2mqtt, Z-Stack-firmware, Ubiqua Protocol Analyzer, our custom firmware, or you can even Specific software requires writing your own software.
The MPC8379E-RDB is a highly integrated reference design board based on the NXP MPC837x using Power Architecture® technology .
Gregory Davill is a technical expert from Australia who is very famous and active in the field of open source hardware. In December 2020, he insisted on designing a circuit board every day, using KiCad to complete the circuit design and PCB layout and routing. This is the adventure-calendar-of-circuits-2020 project. This design is a JTAG programmer based on FT232H.
Apple's full series of drawings: iPhone 5s Chinese schematic + component distribution diagram
The S32K3X4EVB-Q257 is a full-featured evaluation and development board for general automotive applications.
EEWorld
subscription
account
EEWorld
service
account
Automotive
development
community
Robot
development
community
About Us Customer Service Contact Information Datasheet Sitemap LatestNews
Room 1530, 15th Floor, Building B,
No.18 Zhongguancun Street,
Haidian District,
Beijing, Postal Code: 100190
China
Telephone: 008610 8235 0740
京公网安备 11010802033920号
