EEWORLDEEWORLDEEWORLD

Part Number

Search

B22AV-GC

Description
Toggle Switches SUBMINIATURE TOGGLE/PC IP65
CategoryTopical application    Mechanical and electrical/engineering/automation   
File Size1MB,9 Pages
ManufacturerNKK
Websitehttps://www.nkkswitches.com.cn
Download Datasheet Parametric View All

B22AV-GC Online Shopping

Suppliers Part Number Price MOQ In stock  
B22AV-GC - - View Buy Now

B22AV-GC Overview

Toggle Switches SUBMINIATURE TOGGLE/PC IP65

B22AV-GC Parametric

Parameter NameAttribute value
Product CategoryToggle Switches
ManufacturerNKK
RoHSDetails
Contact FormDPDT
Switch FunctionON - ON
Mounting StyleThrough Hole
Voltage Rating AC28 VAC
Voltage Rating DC28 VDC
Power Rating0.4 VA
ActuatorBat
Terminal SealSealed
Contact PlatingGold
ColorRed
Contact MaterialCopper Alloy
Housing MaterialPolyamide, Glass Fiber Reinforced
Mounting AngleVertical
Operating Temperature Range- 30 C to + 85 C
TypeProcess Sealed Subminiature Antistatic Toggles
Series B
Toggles
Process Sealed Subminiature Antistatic Toggles
A
General
Specifications
Electrical Capacity (Resistive Load)
Logic Level:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Pushbuttons
Rockers
Other Ratings
Programmable Illuminated PB
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Keylocks
Contact Timing:
Angle of Throw:
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
100,000 operations minimum for On-None-On & On-Off-On
50,000 operations minimum for other circuits
50,000 operations minimum for locking lever models
50,000 operations minimum
Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)
Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)
Toggle L: 0.59N
Nonshorting (break-before-make)
26°
Materials & Finishes
Rotaries
Toggle:
Bushing:
Gasket:
Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Nickel plated brass
Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing
Nitrile butadiene rubber
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Copper alloy with gold plating
Copper alloy with gold plating
Tactiles
Slides
Environmental Data
Operating Temperature Range:
Humidity:
Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
2
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Touch
Installation
Mounting Torque:
.30 ~ .45Nm (2.65 ~ 3.98 lb
in) for A1 actuator with threaded bushing only
PCB Processing
Indicators
Soldering:
Cleaning:
Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Automated cleaning. See Cleaning specifications in Supplement section.
Accessories
Standards & Certifications
Flammability Standards:
Supplement
UL94V-0 available
The B Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
A12
www.nkkswitches.com
TMS320F28335 Study Notes - Startup Process
1.What is the starting address after DSP reset? 0x3FFFC0 2. What are the steps to burn a program into the emulator? Burn the program to the specified location according to the cmd file and then execut...
fish001 Microcontroller MCU
Can we start a DIY activity of FPGA USB emulator?
I have only seen FPGA boards on the forum, but where can I get an emulator? I hope the forum can launch a DIY activity of "FPGA emulator with USB interface", thank you...
desk1983 FPGA/CPLD
24bit ECC issues
The nand flash of TH58NVG6D2ETA20 requires 1KB 24-bit ECC. If I use 512B 12-bit ECC instead, will there be any risk? Thank you~~ What factors are related to the bit error rate of nand flash?...
cushat Embedded System
ST touch library anti-interference problem
I have made several products using the ST touch library. There are no problems in the office test,but the sensitivity is significantly reduced when it comes to production in the workshop.The total shi...
lygtian stm32/stm8
PIC level change interrupt
I am using PIC16F1823 chip, and I am very distressed that the level change interrupt cannot be accessed. I hope to get help from friends on the forum. The following is my program: #include htc.h #incl...
3050122050 MCU
Bottom-level development
I am doing wince driver development and bootloader development (under ARM). What preparatory knowledge do I need? Or how do I learn it? Please give me the steps, thank you!...
jw_1001 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1638  2051  1908  2853  1799  33  42  39  58  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号