This specification defines the performance, test, quality and reliability requirements of the USB+Power
(Universal Serial Bus with keyed power terminals) including the following: Series “A” Right Angle
2.0
SCOPE:
This specification is applicable to the termination characteristics of the USB+ Power family of products,
which provides interconnection of computer peripherals.
3.0
GENERAL
This document is composed of the following sections:
Paragraph
1.
2.
3.
4.
5.
5.1
5.2
5.3
5.4
5.5
6.
7.
8.
9.
9.1
9.2
9.3
9.4
9.5
9.6
Figure 1
Figure 2
Table 1
Title
OBJECTIVE
SCOPE
GENERAL
APPLICABLE DOCUMENTS
REQUIREMENTS
Qualification
Product Examination
Material
Finish
Design and Construction
ELECTRICAL CHARACTERISTICS
MECHANICAL CHARACTERISTICS
ENVIRONMENTAL CHARACTERISTICS
QUALITY ASSURANCE PROVISIONS
Equipment Calibration
Inspection Conditions
Sample Quantity And Description
Acceptance
Qualification Testing
Re-qualification Testing
CONTACT RESISTANCE MEASUREMENT POINTS
SHOCK AND VIBRATION MOUNTING FIXTURE
QUALIFICATION TESTING AND SEQUENCE MATRIX
This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in
any way without the written consent of FCI Electronics.
Form E-3005
Rev A 02/12/01
V20603
GS-01-001
PDM: Rev:J
PDM: Rev:K
STATUS:
Released
Released
Printed: May
28, 2010
.
Nov
06,
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
(Was GES-12-130)
REVISION
GS-12-130
USB + Power Product Specification
2 of 16
AUTHORIZED BY
K
DATE
XK
ZHANG
07/05/10
CLASSIFICATION
UNRESTRICTED
4.0
APPLICABLE DOCUMENTS
4.1
Specifications:
4.1.1 Engineering Drawings
55917, 57489,10063583
74233, 57496
4.2
Military Standards:
4.2.1 MIL-STD-202F:
4.2.2 MIL-STD-1344A:
4.2.3 MIL-C-45662:
USB + Power Receptacle Assembly
USB + Power Plug Assembly
Test Methods for Electronic Component Parts
Test Methods for Electrical Connectors
Equipment Calibration
4.3
Federal Specifications:
4.3.1 QQ-N-290:
4.3.2 QQ-B-750:
4.3.3 QQ-S-571:
Nickel Plating (Electrodeposited)
Phosphor Bronze Alloy Strip
Solder
4.4
Other Standards and Specifications:
4.4.1 UL94:
Flammability
4.4.2 ASTM B-103:
Phosphor Bronze
4.4.3 ISO 9000:
4.4.4 EIA 364:
Electrical connector/socket test procedures including
environmental classifications
4.4.5 ASTM-D-4565:
Physical and Environmental Performance Properties of
Insulation and Jacket for Telecommunications Wire and
Cable, Test Standard Method
4.4.6 ASTM-D-4566:
Electrical Performance Properties of Insulation and
Jacket for Telecommunication Wire and Cable, Test
Standard Method
4.4.7 USB
Universal Serial BUS Specification
4.5
Berg Specifications:
4.5.1
BUS-03-114:
4.5.2
BUS-03-404:
4.5.3
BUS-03-405:
4.5.4
BUS-03-601:
4.5.5
BUS-16-016:
4.5.6
BUS-16-074:
4.5.7
BUS-19-002:
4.5.8
BUS-19-020:
4.5.9
BUS-19-040:
4.5.10 BUS-19-002:
4.5.11 BUS-19-122:
Capacitance Measurement
Normal Force Measurement
Insertion/Withdrawal Force Measurement
Current Rating/30° Temperature Rise
Phosphor Bronze Strip
PCT, 30% glass
Solderability
Porosity
Plating Adhesion
Surface Mount Solder Joint Reliability
Solder Joint Reliability Test Procedure for Surface Mount
Connectors
This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in
any way without the written consent of FCI Electronics.
Form E-3005
Rev A 02/12/01
V20603
GS-01-001
PDM: Rev:J
PDM: Rev:K
STATUS:
Released
Released
Printed: May
28, 2010
.
Nov
06,
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
(Was GES-12-130)
REVISION
GS-12-130
USB + Power Product Specification
3 of 16
AUTHORIZED BY
K
DATE
XK
ZHANG
07/05/10
CLASSIFICATION
UNRESTRICTED
5.0
REQUIREMENTS
5.1
Qualification
Connectors furnished under this specification shall be capable of meeting the qualification test
requirements specified herein.
5.2
Product Examination
Product will be examined per EIA-364-18 verifying visually paragraphs 5.3, 5.4, and 5.5.
Dimensional examination is not required.
5.3
Material
Material for each part shall be specified herein, or equivalent. Substitute material shall meet the
performance requirements of this specification.
5.3.1
Receptacle and Plug Terminal
- The material shall be high strength copper alloy strip.
5.3.2
Receptacle and Plug Insulator Housings and Covers
- Connectors shall be molded of
plastic that is rated UL94-V-0 or better in accordance with UL-94.
5.3.3
Receptacle and Plug Shell
- The base material shall be phosphor-bronze strip.
5.3.4
Insulator housings and covers of lead free part
- The insulator housings and covers of lead
o
free part will withstand exposure to 260 C peak temperature for 40 seconds in a
convection, infra-red or vapor phase reflow oven. For 10063583, it also can withstand
o
exposure to 260 C peak temperature for 10 seconds for 3 times.
5.3.5
Lead free products
– All lead free products are RoHS compatible.
5.4
Finish
5.4.1
Receptacle and Plug terminals
- shall be plated in the contact area with 0,76um (30
µinches)
palladium nickel with gold flash minimum over 1,27um (50
µinches)
minimum nickel. The
receptacle terminal solder tail sections shall be plated with 2,54um (100
µinches)
90/10 tin-
lead minimum or 2,54um (100
µinches)
minimum matted tin for lead free part over 1,27um
(50
µinches)
minimum nickel. The terminal areas outside of the contact areas and the
solder tail areas shall be plated with 1,27um (50
µinches)
nickel minimum.
5.4.2
Outside shells
- shall be plated with 2, 00um (75µinches) minimum 90/10 bright tin-lead
over 1,27um (50
µinches)
minimum nickel underplate or 2, 00um (75µinches) minimum
bright tin over 1,27um (50
µinches)
minimum nickel underplate or only 1.27um (50 micro
inches) minimum nickel.
5.4.3
Lead free plating
- All plating chemical for lead free part are qualified by FCI. FCI
qualification include solderability, whiskering, solder joint reliability and tarnishing effects.
5.5
Design and Construction
This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in
any way without the written consent of FCI Electronics.
Form E-3005
Rev A 02/12/01
V20603
GS-01-001
PDM: Rev:J
PDM: Rev:K
STATUS:
Released
Released
Printed: May
28, 2010
.
Nov
06,
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
(Was GES-12-130)
REVISION
GS-12-130
USB + Power Product Specification
4 of 16
AUTHORIZED BY
K
DATE
XK
ZHANG
07/05/10
CLASSIFICATION
UNRESTRICTED
5.5.1
Receptacle connector
- is a multiple piece assembly having a lower single row of contacts
(USB standard terminals) spaced on dissimilar centerlines (the two inner contacts are
spaced 2.0mm apart and the terminals adjacent to these terminals are spaced 2.5mm
away) in the interface area. The Upper row of contacts used for power transmission is
spaced 2.5mm apart. Each terminal transition will be a 90 degree bend to allow for
termination to the PC board by a through hole leg. The outside shell has six resilient
contact arms (four on the sides and two on the bottom) that act as ESD grounding as well
as cable plug retention features. The two arms on the side of the shell assure that there is
constant contact between the shell and the shell of the cable assembly plug while the
connectors are mated. The receptacle is has a recess to accommodate the spring latch on
the plug connector. The entire receptacle assembly is attached to the printed circuit board
via four retention claws on the outside shell. The connector has four keys for various
supply voltages. Refer to the Customer Drawing for recommended P.C. Board thickness
and keying positions.
5.5.2
The plug connector
- is a multiple piece assembly having a lower single row of contacts
(USB standard terminals) spaced on dissimilar centerlines (the two inner contacts are
spaced 2.0mm apart and the terminals adjacent to these terminals are spaced 2.5mm
away) in the interface area. The Upper row of contacts used for power transmission is
spaced 2.5mm apart. Each terminal is straight and is soldered to the cable connectors.
The connector is fitted with two shells. The front shell when mated with the receptacle is in
contact with the resilient contact arms of the receptacle providing EMI protection. The rear
shell provides EMI protection as well as clamps to the cable providing a specified cable
strain relief pull force. The outside shell has six resilient contact arms (four on the sides
and two on the bottom) that act as ESD grounding as well as cable plug retention features.
The two arms on the side of the shell assure that there is constant contact between the
shell and the shell of the cable assembly plug while the connectors are mated. A plastic
spring latch on top of the connector positively latches into the receptacle connector when
mated. The connector provides four keying positions for various supply voltages. Refer to
the Customer Drawing keying positions.
5.5.3
Mating
- The connectors shall be capable of mating and unmating manually without the use
of special tools.
5.5.4
Workmanship
- Connectors shall be uniform in quality and shall be free from burrs,
scratches, cracks, voids, chips, blisters, pin holes, sharp edges, other defects, debris and
any ingress of foreign material that will adversely affect life or serviceability.
5.5.5
Temperature Rating
- The receptacle connector shall be capable of withstanding a storage
temperature range of -55
o
C to
85
o
C and an operating temperature range of
-55
o
C to
85
o
C.
6.0
ELECTRICAL CHARACTERISTICS
6.1
Low Level Contact Resistance(LLCR)
6.1.1
6.1.2
6.1.3
Test Standard:
Acceptance Criteria:
Connection Method:
EIA 364-23
30mΩ max.
Attach current and voltage leads as shown in Figure 1
for p/n 55917, 74233/ Figure 3 for p/n 57489, 57496
This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in
any way without the written consent of FCI Electronics.
Form E-3005
Rev A 02/12/01
V20603
GS-01-001
PDM: Rev:J
PDM: Rev:K
STATUS:
Released
Released
Printed: May
28, 2010
.
Nov
06,
.
TYPE
NUMBER
PRODUCT SPECIFICATION
TITLE
PAGE
(Was GES-12-130)
REVISION
GS-12-130
USB + Power Product Specification
5 of 16
AUTHORIZED BY
K
DATE
XK
ZHANG
07/05/10
CLASSIFICATION
UNRESTRICTED
6.2
Insulation Resistance
6.2.1
6.2.2
6.2.3
6.2.4
6.2.5
Test Standard:
Acceptance Criteria:
Test Voltage:
Electrification Time:
Measurement Points:
EIA 364-21
>1000 megohms, mated and unmated
500 volts DC
2 minutes
Between adjacent contacts and between contacts shell
This document is the property of and embodies CONFIDENTIAL and PROPRIETARY information of FCI Electronics. No part of the information shown on this document may be used in
any way without the written consent of FCI Electronics.
Step 1: Release the programStep 2: Download the updateThe third step is the encryption algorithm inside the program. I add a random number to the MAC address of the device and encrypt it with the MD5 ...
There is an LED on the board, and the LED flashing is achieved by modifying the GPIO routine under LPCXpresso v3.2. Briefly introduce the usage and upload the code....
I want to develop an automotive electronic product, but I don't know much about it. I come to your place and hope to get your help. Full-time or part-time is fine. QQ: 350860709, [email=LIKANG888@TOM....
I saw this kind of screen on the Internet. It looks like a square screen. The display content and screen backlight look good. It can display a lot of content. It can display 11 lines of text verticall...
[align=left][font=宋体]This article was written by [/font]ADI[font=宋体]engineer, original text: [/font]https://ezchina.analog.com/thread/17644[/align][align=left] [/align][align=left] [/align][align=left...
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
The intelligent driving community has its own rhythm. Some are busy pushing new versions and focusing on R&D, others are busy with publicity and promotion, and still others are immersed in mass pro...[Details]
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
New energy vehicles are increasingly popular with consumers due to policies and energy conservation. Once you've purchased your vehicle, maintenance is essential. However, due to the different powe...[Details]
The mass production process of the new generation of cockpit platform has started, and the smart cockpit market has entered a new bonus cycle of technology iteration and platform upgrade.
...[Details]
Definition of interactive projection system:
Interactive projection systems, also known as multimedia interactive projection, are available in floor, wall, and tabletop interactive projection....[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
The digital TV set-top box consists of a tuner, QAM demodulator, TS demultiplexer, MPEG-2 decoder, PAUNTSC video encoder, embedded CPU system and peripheral interfaces, CA module, and uplink data m...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
A human-machine interface (HMI) refers to the platform used by people to operate a PLC. This platform provides an interface between programs and humans, serving as a medium for information transmis...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
