MN103S927, MN103S92A
Type
Internal ROM
Internal RAM
Package
Minimum Instruction
Execution Time
Interrupts
Timer Counter
MN103S927
16K-byte
2K-byte
LQFP064-P-1414
*Lead-free
25 ns (at 3.0 V to 3.6 V, 10 MHz)
*at internal 4 times oscillation used)
•
8 external interrupts
•
18 internal interrupts (watch dog timer, timer, serial I/F, PWM, A/D, system error)
8-bit timer
×
4
Timer 0 to 3: Interval timer, Event counter, Cascading connectable
16-bit timer
×
2
Timer 8: Interval timer, Event counter, PWM output (6 pins simultaneous output are available), Double buffer
Timer 11: Interval timer, Double buffer, Start synchronized with 3-phase PWM are available
Watch dog timer
UART (full duplex) / synchronous interfaces selective
×
1
Serial 2: 1-bit to 8-bit transmission (synchronous), 2 and 3 channel type selectable (synchronous)
MN103S92A (under development)
32 K-byte
Serial Interface
I/O Pins
I/O
Input
A/D Inputs
41
8
Exclusive
×
11, selective
×
30
Selective
×
8
10-bit
×
3 unit, 2 inputs
×
1, 6 inputs
×
1
Simultaneous conversion of 2 series are available, With S/H,
Conversion start synchronized with 3-phase PWM or timer 11 are available
16-bit 3-phase PWM
×
1
Minimum resolution: 50 ns
Triangular waveform or jigsaw waveform dead time setup,
Double buffer, Output polar switching is available, PWM output pin protect function
Motor Control PWM
Electrical Characteristics
A/D converter characteristics
Parameter
Non-linear error
A/D conversion time
Analog input voltage
tAD
VIA
Limit
Symbol
Condition
min
10-bit
1.5
VSS
VDD
typ
max
±3
LSB
µs
V
Unit
(Ta
=
25°C, VDD
=
3.0 V, VSS
=
0 V)
MAF00016BEM
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of
the products or technical information described in this material and controlled under the "Foreign Exchange
and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative characteristics and
applied circuits examples of the products. It neither warrants non-infringement of intellectual property right
or any other rights owned by our company or a third party, nor grants any license.
(3) We are not liable for the infringement of rights owned by a third party arising out of the use of the technical
information as described in this material.
(4) The products described in this material are intended to be used for standard applications or general elec-
tronic equipment (such as office equipment, communications equipment, measuring instruments and house-
hold appliances).
Consult our sales staff in advance for information on the following applications:
•
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combus-
tion equipment, life support systems and safety devices) in which exceptional quality and reliability are
required, or if the failure or malfunction of the products may directly jeopardize life or harm the human
body.
•
Any applications other than the standard applications intended.
(5) The products and product specifications described in this material are subject to change without notice for
modification and/or improvement. At the final stage of your design, purchasing, or use of the products,
therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifica-
tions satisfy your requirements.
(6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rat-
ing, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not
be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of
break down and failure mode, possible to occur to semiconductor products. Measures on the systems such
as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent
physical injury, fire, social damages, for example, by using the products.
(7) When using products for which damp-proof packing is required, observe the conditions (including shelf life
and amount of time let standing of unsealed items) agreed upon when specification sheets are individually
exchanged.
(8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written
permission of Matsushita Electric Industrial Co., Ltd.
2003 SEP
京公网安备 11010802033920号
EEWORLD
