EEWORLDEEWORLDEEWORLD

Part Number

Search

HJ65835KBD

Description
RESISTOR, 1W, 0.1%, 25ppm, 835000ohm, THROUGH HOLE MOUNT, AXIAL LEADED
CategoryPassive components    The resistor   
File Size53KB,2 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Environmental Compliance
Download Datasheet Parametric View All

HJ65835KBD Overview

RESISTOR, 1W, 0.1%, 25ppm, 835000ohm, THROUGH HOLE MOUNT, AXIAL LEADED

HJ65835KBD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerTE Connectivity
package instructionAXIAL LEADED
Reach Compliance Codeunknown
Other featuresHIGH PRECISION
structureCylindrical
Lead diameter0.8 mm
Lead length38 mm
Manufacturer's serial numberHJ
Installation featuresTHROUGH HOLE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package diameter4.5 mm
Package length14.5 mm
Package shapeTUBULAR PACKAGE
Package formAxial
Rated power dissipation(P)1 W
Rated temperature25 °C
resistance835000 Ω
Resistor typeFIXED RESISTOR
seriesHJ
surface mountNO
technologyMETAL GLAZE/THICK FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWIRE
Tolerance0.1%
Operating Voltage2000 V
Base Number Matches1
High Precision / High Voltage Resistors
Type HJ Series
Type HJ Series
Characteristics -
Electrical
Type
HJ55
HJ60
HJ65
HJ70
HJ80
Power Rating
@ 25°C
(W)
0.25W
0.5W
1.0W
2.0W
3.0W
Max. Working
Voltage DC
(kV)
0.75
1.5
2.0
5.0
10.0
Impulse Voltage
(kV) 1.2 x 50
Microseconds
1.5
3.0
4.0
10.0
20.0
Resistance
Range
(Ohms)
100K-100M
100K-100M
100K-100M
100K-100M
1M-100M
Resistance
Tolerance
(%)
0.1, 0.25
0.1, 0.25
0.1, 0.25
0.1, 0.25
0.1, 0.25
Temperature
Coefficient
(ppm)
±25, ±50, ±100
±25, ±50, ±100
±25, ±50, ±100
±25, ±50, ±100
±25, ±50, ±100
The HJ type resistors have higher
reliability when they are mounted on
board, and excellent long term stability.
These are used mainly in semi-
conductor equipments, X-ray appara-
tus, and many other measuring
instruments.
Characteristics -
Environmental
Test Item
Operating Temperature Range:
Short Term Overload:
Resistance to Soldering Heat:
Thermal Shock:
Characteristics
-55°C to +150°C
±0.1%
±0.1%
±0.1%
±0.3%
±0.3%
±0.5%
“D” ±25ppm
“C” ±50ppm
“Z” ±100ppm
Rated Voltage x 2.5 applied for 5 seconds
260°C for 10 seconds or 380°C for
3 seconds
-55°C to +150°C, 5 cycles
At normal temperature and humidity for
10,000 hours without load
40°C 90 ~ 95%RH for 1,000 hours
exposure without load
25°C Rated power x _ for 1,000 hours
The test data is based on a temperature
difference of 50°C (reference temperature
25°C; measurement temperature, 75°C)
Test Method
Key Features
I
I
I
I
I
I
I
I
Long Term Stability:
Moisture Resistance:
Load Life:
Temperature Coefficient:
Low TCR’s
Close Resistance Tolerances
Small compact size
High Reliability
Excellent long-term stability
High resistance to pulse
voltages
Special Coatings for High
Humidity
High thermal shock
resistance when mounted
to PCB
Derating Curve
100
80
Rated Power Ratio
60
40
20
0
0
25
50
75
100
125
150
Ambient Temperature (°C)
Literature No. 1773226
Issued: 04-05
Dimensions are shown for
reference purposes only.
Dimensions are in millimetres
unless otherwise specified.
Specifications subject to
change.
www.tycoelectronics.com
passives.tycoelectronics.com
What is the appropriate output filter capacitor for TL431?
What is the appropriate output filter capacitor for TL431? I oscillated when I output 10UF. I was depressed for several days. Haha...
kata Analog electronics
EPI configuration uDMA problem
Experts: I use the F28M36x series DSP, and configure uDMA on the TX side of EPI in the M3 core. The uDMAChannelTransferSet() function needs to set the destination address. Is the destination address t...
escort DSP and ARM Processors
Teach you how to use operational amplifiers
I found this on the Internet. I hope you can learn from it and grow together....
lg1981p1026 Analog electronics
Several key points for chip selection in R&D
Comprehensive introduction to isolation in electronic circuits - Several key points in chip selection in R&D (serial 6) Author: Jerrymiao, Jingyuan With the continuous updating of integrated circuit t...
shehua2010 PCB Design
Questions about op amp parameters
As shown in the red box in the picture, what does RS stand for? Thank you!...
xiaxingxing Analog electronics
Show the process of WEBENCH design + high-pass filter design
Step 1: Select high pass filterStep 2: Select filter type and change parametersStep 3: Select the first type settingStep 4: Design screenshotStep 5: Output CAD file...
youzizhile Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2243  941  1769  739  735  46  19  36  15  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号