Features
•
Core
– ARM
®
Cortex
®
-M3 revision 2.0 running at up to 96 MHz
– Memory Protection Unit (MPU)
– Thumb
®
-2 instruction set
Memories
– From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator,
dual bank
– From 16 to 48 Kbytes embedded SRAM with dual banks
– 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines
– Static Memory Controller (SMC): SRAM, NOR, NAND support. NAND Flash
controller with 4 Kbytes RAM buffer and ECC
System
– Embedded voltage regulator for single supply operation
– POR, BOD and Watchdog for safe reset
– Quartz or resonator oscillators: 3 to 20 MHz main and optional low power 32.768
kHz for RTC or device clock.
– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz Default
Frequency for fast device startup
– Slow Clock Internal RC oscillator as permanent clock for device clock in low power
mode
– One PLL for device clock and one dedicated PLL for USB 2.0 High Speed Device
– Up to 17 peripheral DMA (PDC) channels and 4-channel central DMA
Low Power Modes
– Sleep and Backup modes, down to 2.5 µA in Backup mode
– Backup domain: VDDBU pin, RTC, 32 backup registers
– Ultra low power RTC: 0.6 µA
Peripherals
– USB 2.0 Device: 480 Mbps, 4-kbyte FIFO, up to 7 bidirectional Endpoints,
dedicated DMA
– Up to 4 USARTs (ISO7816, IrDA
®
, Flow Control, SPI, Manchester support) and one
UART
– Up to 2 TWI (I2C compatible), 1 SPI, 1 SSC (I2S), 1 HSMCI (SDIO/SD/MMC)
– 3-Channel 16-bit Timer/Counter (TC) for capture, compare and PWM
– 4-channel 16-bit PWM (PWMC)
– 32-bit Real Time Timer (RTT) and RTC with calendar and alarm features
– 8-channel 12-bit 1MSPS ADC with differential input mode and programmable gain
stage, 8-channel 10-bit ADC
I/O
– Up to 96 I/O lines with external interrupt capability (edge or level sensitivity),
debouncing, glitch filtering and on-die Series Resistor Termination
– Three 32-bit Parallel Input/Outputs (PIO)
Packages
– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm
– 100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm
– 144-lead LQFP, 20 x 20 mm, pitch 0.5 mm
– 144-ball TFBGA, 10 x 10 mm, pitch 0.8 mm
•
•
AT91SAM
ARM-based
Flash MCU
SAM3U Series
Summary
•
•
•
•
NOTE:
This is a summary document.
The complete document is available on
the Atmel website at www.atmel.com.
6430FS–ATARM–10-Feb-12
1. SAM3U Description
Atmel's SAM3U series is a member of a family of Flash microcontrollers based on the high per-
formance 32-bit ARM Cortex-M3 RISC processor. It operates at a maximum speed of 96 MHz
and features up to 256 Kbytes of Flash and up to 52 Kbytes of SRAM. The peripheral set
includes a High Speed USB Device port with embedded transceiver, a High Speed MCI for
SDIO/SD/MMC, an External Bus Interface with NAND Flash controller, up to 4xUSARTs
(SAM3U1C/2C/4C have 3), up to 2xTWIs (SAM3U1C/2C/4C have 1), up to 5xSPIs
SAM3U1C/2C/4C have 4), as well as 4xPWM timers, 3xgeneral purpose 16-bit timers, an RTC,
a 12-bit ADC and a 10-bit ADC.
The SAM3U architecture is specifically designed to sustain high speed data transfers. It includes
a multi-layer bus matrix as well as multiple SRAM banks, PDC and DMA channels that enable it
to run tasks in parallel and maximize data throughput.
It can operate from 1.62V to 3.6V and comes in 100-pin and 144-pin LQFP and BGA packages.
The SAM3U device is particularly well suited for USB applications: data loggers, PC peripherals
and any high speed bridge (USB to SDIO, USB to SPI, USB to External Bus Interface).
1.1
Configuration Summary
The SAM3U series differ in memory sizes, package and features list.
Table 1-1
summarizes the
configurations of the six devices.
Table 1-1.
Configuration Summary
Flash
Organization SRAM
dual plane
52
Kbytes
36
Kbytes
20
Kbytes
52
Kbytes
36
Kbytes
20
Kbytes
Number
of PIOs
96
Number
of
USARTs
4
Number
of TWI
2
FWUP,
SHDN
pins
Yes
External Bus
Interface
8 or 16 bits,
4 chip selects,
24-bit address
8 or 16 bits,
4 chip selects
24-bit address
8 or 16 bits,
4 chip selects,
24-bit address
8 bits,
2 chip selects,
8-bit address
HSMCI
data
size
8 bits
Device
SAM3U4E
Flash
2x128
Kbytes
128
Kbytes
64
Kbytes
2 x 128
Kbytes
128
Kbytes
64
Kbytes
Package
LQFP144
BGA144
LQFP144
BGA144
LQFP144
BGA144
LQFP100
BGA100
LQFP100
BGA100
LQFP100
BGA100
ADC
2 (8+ 8
channels)
2 (8+ 8
channels)
2 (8+ 8
channels)
2 (4+ 4
channels)
2 (4+ 4
channels)
2 (4+ 4
channels)
SAM3U2E
single plane
96
4
2
Yes
8 bits
SAM3U1E
single plane
96
4
2
Yes
8 bits
SAM3U4C
dual plane
57
3
1
FWUP
4 bits
SAM3U2C
single plane
57
3
1
FWUP
8 bits,
2 chip selects, 8- 4 bits
bit address
8 bits
2 chip selects,
8-bit address
4 bits
SAM3U1C
single plane
57
3
1
FWUP
Note:
1. The SRAM size takes into account the 4-Kbyte RAM buffer of the NAND Flash Controller (NFC) which can be used by the
core if not used by the NFC.
2
SAM3U Series
6430FS–ATARM–10-Feb-12
SAM3U Series
3. Signal Description
Table 3-1
gives details on the signal names classified by peripheral.
Table 3-1.
Signal Name
Signal Description List
Function
Type
Power Supplies
Active
Level
Voltage
Reference Comments
VDDIO
VDDIN
VDDOUT
VDDUTMII
GNDUTMII
VDDBU
GNDBU
VDDPLL
GNDPLL
VDDANA
GNDANA
VDDCORE
GND
Peripherals I/O Lines Power Supply
Voltage Regulator Input
Voltage Regulator Output
USB UTMI+ Interface Power Supply
USB UTMI+ Interface Ground
Backup I/O Lines Power Supply
Backup Ground
PLL A, UPLL and OSC 3-20 MHz Power Supply
PLL A, UPLL and OSC 3-20 MHz Ground
ADC Analog Power Supply
ADC Analog Ground
Core, Memories and Peripherals Chip Power
Supply
Ground
Power
Power
Power
Power
Ground
Power
Ground
Power
Ground
Power
Ground
Power
Ground
1.62V to 3.6V
1.8V to 3.6V
1.8V
3.0V to 3.6V
1.62V to 3.6V
1.62 V to 1.95V
2.0V to 3.6V
1.62V to 1.95V
Clocks, Oscillators and PLLs
XIN
XOUT
XIN32
XOUT32
VBG
PCK0 - PCK2
Main Oscillator Input
Main Oscillator Output
Slow Clock Oscillator Input
Slow Clock Oscillator Output
Bias Voltage Reference
Programmable Clock Output
Input
Output
Input
Output
Analog
Output
Shutdown, Wakeup Logic
push/pull
0: The device is in
backup mode
1: The device is running
(not in backup mode)
Needs external pull-up
VDDIO
VDDBU
VDDPLL
SHDN
Shut-Down Control
Output
VDDBU
FWUP
Force Wake-Up Input
Input
Low
Serial Wire/JTAG Debug Port (SWJ-DP)
TCK/SWCLK
TDI
TDO/TRACESWO
TMS/SWDIO
JTAGSEL
Test Clock/Serial Wire Clock
Test Data In
Test Data Out/Trace Asynchronous Data Out
Test Mode Select/Serial Wire Input/Output
JTAG Selection
Input
Input
Output
(4)
Input
Input
High
VDDBU
VDDIO
No pull-up resistor
No pull-up resistor
No pull-up resistor
Internal permanent
pull-down
5
6430FS–ATARM–10-Feb-12
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
