ST6-EMU2
ST6-EMU2 emulator
Data brief
Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
One power cable
Two ferrites to be clipped over the flat cables
(for EMC compliance)
Step-by-step debugging
Breakpoints
2 trigger outputs
Analyzer probe input connector for up to 4
external signals
Parallel port interfaces to the host PC
Clock frequency up to 8 MHz
Emulation voltage: 5 V
ST6 assembler and linker, AST6 and LST6
ST6 Windows debugger, WGDB6
Windows ST6 microcontroller programmer,
Epromer
ST62GP-EMU2 box with two flat cables for
connecting a probe
One DB324/DIP probe board for use with
ST6230, ST6218 and ST6228 target devices
One DB324/SDIP42 probe board for use with
the ST6232 target device
One DB448 probe board for use with ST620x,
ST621x and ST622x target devices
One DB449 probe board for use with 5x and 6x
devices, including:
– 16-pin probe with 3 different male-male
interfaces, depending on the target device
– 20-pin probe with 3 different male-male
interfaces, depending on the target device
– 28-pin probe with 3 different male-male
interfaces, depending on the target device
Analyser probes
Three probe adapters—DIP16, DIP20 and
DIP28—to be soldered to a footprint
Three SO adapters—SO16, SO20 and SO28
One parallel interface cable (Ref.:
DB25M/DB25M)
One power adapter
Description
The ST6-EMU2 provides you with all you need to
develop and debug programs for ST6
microcontrollers.
STMicroelectronics' ST6-EMU2 emulators are
cost-effective solutions that provide both high
quality, emulation and programming capability to
support ST6 application development.
Emulators are delivered with WGDB6, which
allows debugging of ST6 applications using a
Windows PC as the user interface.
Windows Epromer allows the user to program
application code in the ST6 EPROM.
■
■
■
■
■
October 2010
Doc ID 18105 Rev 1
1/4
www.st.com
4
For further information contact your local STMicroelectronics sales office.
ST6-EMU2
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
4/4
Doc ID 18105 Rev 1
Training Edition
京公网安备 11010802033920号
EEWORLD
