The RP20-AW series are ultraminiature wide input voltage range power DC/DC converters in a case
half the size of industry standard 20W converters. Despite their small size, the RP20-AW converters are
fully specified devices with output currents up to 4.5 Amps, up to 90% efficiency, no minimum load,
1600VDC isolation, a built-in Class A EMC filter and low ripple/noise figures. The outputs are also fully
protected against short circuits, overcurrent and overvoltage. The no load input current is particularly
low (only 4mA/6mA). The RP20-AW series will find many uses in applications where board space and/
or board height is at a premium or in battery-powered systems where standby current is important.
3
EAR
rranty
Selection Guide
Part Number
RP20-243.3SAW
(3,4)
RP20-2405SAW
(3,4)
RP20-2412SAW
(3,4)
RP20-2415SAW
(3,4)
RP20-483.3SAW
(3,4)
RP20-4805SAW
(3,4)
RP20-4812SAW
(3,4)
RP20-4815SAW
(3,4)
RP20-2412DAW
(3,4)
RP20-2415DAW
(3,4)
RP20-4812DAW
(3,4)
RP20-4815DAW
(3,4)
Input
Voltage Range
[VDC]
9-36
9-36
9-36
9-36
18-75
18-75
18-75
18-75
9-36
9-36
18-75
18-75
Output
Voltage
[VDC]
3.3
5
12
15
3.3
5
12
15
±12
±15
±12
±15
Output
Current
[mA]
4500
4000
1670
1330
4500
4000
1670
1330
±833
±667
±833
±667
Input
(1)
Efficiency
(1)
Current
typ.
[mA]
[%]
695
89
936
89
938
89
934
89
356
87
468
89
469
89
462
90
936
89
926
90
468
89
463
90
Max. Capacitive
Load
(2)
[µF]
7000
5000
850
700
7000
5000
850
700
±500
±350
±500
±350
E196683
UL60950-1 Certified
Notes:
Note1: Values at nominal input voltage and full load
Note2: Test by minimum Vin and constant resistor load.
Model Numbering
RP20-__ __ _AW/_ _
Input Voltage
Output Voltage
Single
or
Dual
Ordering Examples
RP20-2405SAW/P = 24V 4:1 Input, 5V Output, Positive Logic CTRL pin and Trim pin fitted.
RP20-483.3SAW-HC = 48V 4:1 Input, 3.3V Output, Premounted Heat-sink, no Trim or CTRL pins.
(trim function is only available for single output with /P or /N suffix)
Notes:
Note3: standard part is without suffixes CTRL & Trim pin aren’t fitted
add suffix “P” for CTRL function with positive logic (1=ON, 0=OFF), including trim pin
add suffix “N” for CTRL function with negative logic (0=ON, 1=OFF), including trim pin
Note4: add suffix -HC for premounted Heat-sink and clips
www.recom-power.com
REV.: 2/2017
PD-1
Package
(5)
Control Logic
(4)
RP20-AW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
BASIC CHARACTERISTICS
Parameter
Input Voltage Range
Series
Condition
nom. Vin = 24V
nom. Vin = 48V
Vin = 24V
DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
Min.
9VDC
18VDc
Typ.
24VDC
48VDC
8VDC
Max.
36VDC
75VDC
9VDC
18VDC
Under Voltage Lockout (UVLO)
Vin = 48V
Input Filter
Input Reflected Ripple Current
(5)
Input Surge Voltage
Start-up time
Operating Frequency Range
Minimum Load
16VDC
Pi-Type
30mAp-p
50VDC
100VDC
30ms
30ms
248kHz
297kHz
0%
275kHz
330kHz
303kHz
363kHz
nominal Vin and full load
Vin = 24V, 100ms max.
Vin = 48V, 100ms max.
Power up
Remote ON/OFF
3.3Vout, 5Vout
Others
measured by 20Mhz bandwidth
Single
with 1µF M/C X7R and a 10µF T/C
75mVp-p
100mVp-p
Open or 3.0V < Vr < 15V
Short or 0V < Vr < 1.2V
Short or 0V < Vr < 1.2V
Open or 3.0V < Vr < 15V
2mA
-0.5mA
1mA
Ripple and Noise
measured by 20Mhz bandwidth
with 1µF M/C X7R and 10µF T/C for Dual
each output
Positive Logic
DC-DC ON
DC-DC OFF
DC-DC ON
DC-DC OFF
Remote ON/OFF
(6)
Negative Logic
Input current of Remote pin (CTRL)
Negative Logic DC-DC OFF
Positive Logic DC-DC ON
Notes:
Note5: Simulated source impedance of 12µH. 12µH inductor in series with +Vin.
RP20-2405SAW
Efficiency vs. Output Current
95
90
85
Efficiency vs. Input Voltage
95
90
Efficiency [%]
80
75
70
65
60
55
50
45
40
10
20
30
40
50
60
70
80
9Vin
24Vin
36Vin
90
100
Efficiency [%]
85
80
75
70
65
9
12
15
18
21
24
27
30
33
36
Output Current [%]
Input Voltage [VDC]
continued on next page
PD-2
REV.: 2/2017
www.recom-power.com
RP20-AW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
RP20-4805SAW
95
90
85
80
70
65
60
55
50
45
40
10
20
30
40
50
60
70
80
36Vin
48Vin
75Vin
90
100
Series
Efficiency vs. Output Current
95
90
Efficiency vs. Input Voltage
Efficiency [%]
Efficiency [%]
75
85
80
75
70
65
18
24
30
36
42
48
54
60
66
72
75
Output Current [%]
Input Voltage [VDC]
REGULATIONS
Parameter
Output Voltage Accuracy
Output Trimming
Line Voltage Regulation
Single
Single
Dual
0% load to 100% load
Load Voltage Regulation
10% load to 100% load
Cross Regulation
Transient Response recovery time
Single
Dual
Single
Dual
Condition
Value
±1%
±10%
±0.2%
±0.5%
±0.2%
±1.0%
±0.1%
±0.8%
±5%
250µs typ.
asymmetrical 25%<>100% load
25% load step change
External Output Trimming
Output Voltage Trimming
Single output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external
trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for chosing these
trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resistor
required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below.
Trim up
6
RU
5
Trim down
RD
4
RP20-xx3.3SAW
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
3.333
57.93
1
3.267
69.47
2
3.366
26.16
2
3.234
31.23
3
3.399
15.58
3
3.201
18.49
5
4
3.432
10.28
4
3.168
12.12
5
3.465
7.11
5
3.135
8.29
6
3.498
4.99
6
3.102
5.74
7
3.531
3.48
7
3.069
3.92
8
3.564
2.34
8
3.036
2.56
9
3.597
1.46
9
3.003
1.50
10
3.63
0.75
10
2.97
0.65
%
Volts
kOhms
%
Volts
kOhms
continued on next page
www.recom-power.com
REV.: 2/2017
PD-3
RP20-AW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
RP20-xx05SAW
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
5.05
36.57
1
4.95
45.53
2
5.10
16.58
2
4.90
20.61
3
5.15
9.92
3
4.85
12.31
4
5.20
6.58
4
4.80
8.15
5
5.25
4.59
5
4.75
5.66
6
5.30
3.25
6
4.70
4.00
7
5.35
2.30
7
4.65
2.81
8
5.4
1.59
8
4.60
1.92
9
5.45
1.03
9
4.55
1.23
10
5.50
0.59
10
4.50
0.68
%
Volts
kOhms
%
Volts
kOhms
Series
RP20-xx12SAW
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
12.12
367.91
1
11.88
460.99
2
12.24
165.95
2
11.76
207.95
3
12.36
98.64
3
11.64
123.60
4
12.48
64.98
4
11.52
81.42
5
12.60
44.78
5
11.40
56.12
6
12.72
31.32
6
11.28
39.25
7
12.84
21.70
7
11.16
27.20
8
12.96
14.49
8
11.04
18.16
9
13.08
8.88
9
10.92
11.13
10
13.20
4.39
10
10.8
5.51
%
Volts
kOhms
%
Volts
kOhms
RP20-xx15SAW
Trim up
Vout =
R
U
=
Trim down
Vout =
R
D
=
1
15.15
404.18
1
14.85
499.82
2
15.3
180.59
2
14.70
223.41
3
15.45
106.06
3
14.55
131.27
4
15.60
68.80
4
14.40
85.20
5
15.75
46.44
5
14.25
57.56
6
15.90
31.53
6
14.10
39.14
7
16.05
20.88
7
13.95
25.97
8
16.20
12.90
8
13.80
16.10
9
16.35
6.69
9
13.65
8.42
10
16.50
1.72
10
13.50
2.282
%
Volts
kOhms
%
Volts
kOhms
PROTECTIONS
Parameter
Short Circuit Protection (SCP)
3.3Vout
5Vout
Zener Diode Clamp
12Vout
15Vout
% of Iout rated; Hiccup mode
I/P to O/P
I/P to O/P to case
500 VDC
Notes:
Note7: This power module is not internally fused. An input line fuse must always be used.
PD-4
REV.: 2/2017
www.recom-power.com
Condition
Value
continuous, automatic recovery
3.7VDC - 5.4VDC
5.6VDC - 7.0VDC
13.5VDC - 19.6VDC
16.8VDC - 20.5VDC
150% typ
1.6kVDC/1 minute
1.0kVDC/1 minute
1GΩ min
1500pF max.
Over Voltage Protection (OVP)
Over Load Protection (OLP)
Isolation Voltage
Isolation Resistance
Isolation Capacitance
RP20-AW
DC/DC Converter
Specifications
measured at Ta = 25°C, nominal input voltage, full load otherwise noted
ENVIRONMENTAL
Parameter
Operating Temperature Range
Maximum Case Temperature
Temperature Coefficient
Thermal Impedance
Operating Humidity
Thermal Shock
Vibration
MTBF
(8)
Bellcore TR-NWT-000332
MIL-HDBK-217F
RP20-4815SAW
100
80
60
40
20
10
0
-40
-20
0
20
40
60
80 100 120
68
94 101
Series
Condition
without derating
with derating
Value
-40°C to +68°C
-40°C to +101°C
+105°C
±0.02%/°C max.
Natural convection
Natural convection with Heat Sink
17.6°C/Watt
14.8°C/Watt
5% - 95% RH
MIL-STD-810F
MIL-STD-810F
1766 x 10
3
hours
1469 x 10
3
hours
Derating Graph
(9)
RP20-4815SAW with Heat-sink
100
80
60
40
20
10
0
-40
-20
0
20
40
60
80
101 120
97
Output Power [%]
Output Power [%]
Ambient Temperature [°C]
Ambient Temperature [°C]
73
Notes:
Note8: BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C.
MIL-HDBK 217F Notice 2. Ta = 25°C, full load, (Ground, Benign, controlled environment).
Note9: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-
number not shown here please contact our technical support service at techsupportAT@recom-power.com.
SAFETY AND CERTIFICATIONS
Certificate Type (Safety)
UL General Safety
Condition
E196683
Standard
UL60950-1 1st Ed.: 2003
C22.2 No. 60950 1st. Ed.: 2003
EMC Compliance
EMI Standard
(10)
ESD
Radiated Immunity
Fast Transient
(11)
Surge
(11)
Conducted Immunity
Condition
with external filter
Air ±8kV and Contact ±6kC
10 V/m
±2kV
±2kV
10 Vr.m.s
Standard / Criterion
EN55022, Class A or B
EN61000-4-2, Criteria A
EN61000-4-3, Criteria A
EN61000-4-4, Criteria A
EN61000-4-5, Criteria A
EN61000-4-6, Criteria A
Notes:
Note10: The standard modules meet EMI Class A or Class B with external components, see filter suggestions below.
Note11: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Recom
A journey of a thousand miles begins with a dumpling~ Hello everyone~ Today is the winter solstice, everyone remember to eat dumplings or glutinous rice balls~
Let's take a look at the news for the ne...
Abstract: Based on the MPEG-4 protocol framework, the MPEG-4 video compression coding algorithm is studied, especially the I-VOP, P-VOP, and B-VOP coding algorithms. A relatively simple implementation...
I would like to ask you a question: I recently used the low-power oscillator chip LTC1966 to generate a square wave of about 2KHz. If I want to connect an inductive load that requires a current of mor...
I was tinkering with the mining board and found the download address of vivado 2018.3. It worked fine, but the software is too large, nearly 20G.Link: https://pan.baidu.com/s/1aa6Cm9yYuejU5kij9bBjFgEx...
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
Battery life is critical for portable applications. For applications such as smoke detectors, security devices, and thermostats, factory-installed batteries need to last for more than 10 years. The...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
The rectified DC voltage is then converted back to AC using power electronics such as insulated gate bipolar transistors.
The output voltage is switched on and off at a high frequency, control...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
Special Edition for Assessment Centres
京公网安备 11010802033920号
EEWORLD
