SCALE™-2 1SP0635x2x1-33
1SP0635x2x1-33
Data Sheet
Compact, high-performance, plug-and-play single-channel IGBT driver based
on SCALE™-2 technology for individual and parallel-connected modules in
2-level, 3-level and multilevel converter topologies
Abstract
The SCALE™-2 plug-and-play driver 1SP0635x2x1-33 is a compact single-channel intelligent gate driver
designed for 3300V 130x140mm and 190x140mm IGBT modules. The master driver 1SP0635x2M1-33 features
a fiber-optic interface with a built-in isolated DC/DC power supply. It can be used as stand-alone driver or in
conjunction with up to three 1SP0635D2S1-33 slaves to drive up to four parallel-connected IGBT modules.
The turn-on and turn-off gate resistors as well as the auxiliary gate capacitor are not assembled
in order to provide maximum flexibility. They must be assembled by the user before start of
operation.
Please refer to the paragraph on “Gate Resistor and Auxiliary Gate Capacitor Assembly” for the
recommended values.
For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to:
www.power.com/igbt-driver/go/plug-and-play
Features
Applications
Plug-and-play solution
Allows parallel connection of IGBT modules
For 2-level, 3-level and multilevel topologies
Built-in isolated DC/DC power supply (master)
Fiber-optic links (master)
Built-in interface to 1SP0635D2S1 (slave)
Duty cycle 0...100%
Dynamic Advanced Active Clamping DA C
Dynamic IGBT short-circuit protection
Monitoring of supply voltage
Monitoring of gate voltage
Extremely reliable; long service life
Shortens application development time
Suitable for 3300V 130x140mm
2
Traction
Railroad power supplies
Light rail vehicles
HVDC
Flexible AC transmission systems (FACTS)
Medium-voltage converters
Industrial drives
Wind-power converters
Medical applications
Research
And many others
Page 1
and 190x140mm IGBT modules
www.power.com/igbt-driver
SCALE™-2 1SP0635x2x1-33
Data Sheet
Safety Notice!
The data contained in this data sheet is intended exclusively for technically trained staff. Handling all high-
voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory!
Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive
devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the
workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged.
Important Product Documentation
This data sheet contains only product-specific data. For a detailed description, must-read application notes and
common data that apply to the whole series, please refer to the “Description & Application Manual for
1SP0635 SCALE-2 IGBT Drivers” on
www.power.com/igbt-driver/go/1SP0635.
The gate resistors as well as the auxiliary gate capacitor on this gate driver are not assembled in order to
provide maximum flexibility. For the values required for specific IGBT modules, refer to the paragraph on
“Gate Resistor and Auxiliary Gate Capacitor Assembly”. Use of gate resistors and gate auxiliary capacitors
other than those specified may result in failure.
Mechanical Dimensions
Dimensions: Refer to the relevant “Description and Application Manual”
Mounting principle: Connected to IGBT module with screws
Fiber-Optic Interfaces (1SP0635x2M1)
Interface
Drive signal input
Drive signal input
Status output
Status output
Remarks
1SP0635V, fiber-optic receiver (Notes 1, 2)
1SP0635S, fiber-optic receiver (Notes 1, 2)
1SP0635V, fiber-optic transmitter (Notes 1, 3)
1SP0635S, fiber-optic transmitter (Notes 1, 3)
Part type #
HFBR-2522ETZ
HFBR-2412Z
HFBR-1522ETZ
HFBR-1412Z
Electrical Connectors
Interface
Power supply connector X1
Bus connectors X2 and X3
Remarks
1SP0635x2M1, on-board connector (Note 4)
On-board connectors (Note 5)
Part type #
214012
214013
www.power.com/igbt-driver
Page 2
SCALE™-2 1SP0635x2x1-33
Data Sheet
Absolute Maximum Ratings
Parameter
Supply voltage V
DC
Average supply current I
DC
Average supply current I
DC
Gate output power
Gate output power
Switching frequency F
Switching frequency F
Gate peak current I
out
Test voltage (50Hz/1min.)
DC-link voltage
Operating voltage
Max. emitter-emitter voltage
|dV/dt|
Max. interface current
Operating temperature
Storage temperature
Remarks
VDC to GND (1SP0635x2M1)
1SP0635x2M1 only (Note 6)
1SP0635x2M1 with three 1SP0635D2S1 (Note 6)
1SP0635x2M1, Ta < 70°C (Note 7)
1SP0635x2M1, Ta = 85°C (Note 7)
1SP0635D2S1, Ta < 70°C (Note 8)
1SP0635D2S1, Ta = 85°C (Note 8)
1SP0635x2M1, Ta < 70°C (Note 31)
1SP0635x2M1, Ta = 85°C (Note 31)
1SP0635D2S1, Ta < 70°C (Note 31)
1SP0635D2S1, Ta = 85°C (Note 31)
Note 9
1SP0635x2M1, primary to secondary (Note 10)
Switching operation (Note 11)
Off state (Note 12)
Primary to secondary side
Between parallel connected drivers (Note 13)
Between parallel connected drivers (Note 14)
X2 and X3, total RMS value (Note 15)
X2 and X3, total peak value (Note 15)
Min
0
Max
Unit
-35
-40
-40
16
V
400
mA
1130
mA
3
W
2.2
W
2.6
W
2
W
n.d.
kHz
n.d.
kHz
n.d.
kHz
n.d.
kHz
+35
A
6000 V
AC(eff)
2200
V
2700
V
3300 V
peak
200 V
peak
50 kV/μs
4
A
rms
20
A
peak
+85
°C
+90
°C
Recommended Operating Conditions
Power Supply
Supply voltage V
DC
Remarks
To GND
Min
14.5
Typ
15
Max
15.5
Unit
V
www.power.com/igbt-driver
Page 3
SCALE™-2 1SP0635x2x1-33
Data Sheet
Electrical Characteristics
All data refer to +25°C and V
DC
= 15V unless otherwise specified
Power Supply
Supply current I
DC
Coupling capacitance C
io
Power Supply Monitoring
Supply threshold V
iso
-V
ee
Monitoring hysteresis
Supply threshold V
ee
-V
COM
Monitoring hysteresis
Bus to 1SP0635D2S1
Supply voltage
Turn-off command
Turn-on command
Gate Monitoring
Turn-on threshold V
GE,on,min
Turn-off threshold V
GE,off,max
Filter delay
Short-circuit Protection
Static Vce-monitoring threshold
Response time
Remarks
Without load, only 1SP0635x2M1
Without load, per additional 1SP0635D2S1
1SP0635x2M1, DC/DC converter
Remarks
Secondary
Secondary
Secondary
Secondary
Secondary
Secondary
Remarks
Without load
With three slaves, full load
To COM
To COM
Remarks
G
mean
to E, set fault (Note 17)
G
mean
to E, set fault (Note 17)
Note 17
Remarks
Between auxiliary terminals (Note 18)
DC-link voltage = 2200V (Note 19)
DC-link voltage = 1500V (Note 19)
DC-link voltage = 1100V (Note 19)
DC-link voltage = 800V (Note 19)
After the response time (Note 20)
Remarks
Note 21
Note 21
Min
Min
Min
side,
side,
side,
side,
side,
side,
clear fault
set fault (Note 16)
set/clear fault
clear fault
set fault (Note 16)
set/clear fault
Min
12.1
11.5
0.35
5
4.7
0.15
Min
Min
Typ
120
35
15
Typ
12.6
12.0
5.15
4.85
Max
13.1
12.5
5.3
5
Max
Unit
mA
mA
pF
Unit
V
V
V
V
V
V
Unit
V
V
V
V
Max
Unit
V
V
μs
Max
Unit
V
μs
μs
μs
μs
μs
Max
Unit
ns
ns
Typ
25
24
0
15
Typ
12.9
-7.6
28
Typ
143
5.9
6.0
6.2
8.3
0.3
Typ
190
185
Max
Delay to IGBT turn-off
Timing Characteristics
Turn-on delay t
d(on)
Turn-off delay t
d(off)
www.power.com/igbt-driver
Page 4
SCALE™-2 1SP0635x2x1-33
Data Sheet
Timing Characteristics
Output rise time t
r(out)
Output fall time t
f(out)
Transmission delay of fault state
Delay to clear fault state
Acknowledge delay time
Acknowledge pulse width
Gate Output
Turn-on gate resistor R
g(on)
Turn-off gate resistor R
g(off)
Auxiliary gate capacitor C
ge
Gate voltage at turn-on
Gate-voltage at turn-off
Remarks
G to E (Note 22)
G to E (Note 22)
Note 23
After IGBT short circuit (Note 24)
After gate-monitoring fault (Notes 24, 30)
Note 25
On host side
Remarks
Note 26
Note 26
Note 26
Note 27
Without load (Note 27)
P
DC/DC
= 3W (Note 27)
P
DC/DC
= 6W (Note 27)
P
DC/DC
= 12W (Note 27)
Remarks
Primary to secondary side (Note 10)
Primary to secondary side (Note 28)
Primary to secondary side (Note 29)
Primary to IGBT main emitter terminal
Clearance distance
Primary to secondary side (Note 29)
Primary to IGBT main emitter terminal
Footnotes to the Key Data
1)
2)
3)
4)
The transceivers required on the host controller side are not supplied with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.power.com/igbt-driver/go/fiberoptics.
The recommended transmitter current at the host controller is 20mA. A higher current may increase
jitter or delay at turn-off.
The typical transmitter current at the gate driver is 18mA. In case of supply undervoltage, the
minimum transmitter current at the gate driver is 12mA: this is suitable for adequate plastic optical
fibers with a length of up to 10 meters.
This refers to the manufacturer ordering number, see
www.power.com/igbt-driver/go/ext_erni.
The
customer-side connector as well as cables with different lengths can be supplied by Power
Integrations. Refer to the “Description & Application Manual for 1SP0635 SCALE-2 IGBT Drivers” for
more information.
This refers to the manufacturer ordering number, see
www.power.com/igbt-driver/go/ext_erni.
These
connectors are to be used to connect 1SP0635x2M1 (master) or 1SP0635D2S1 (slave) to
1SP0635D2S1 (slave) if parallel connection of IGBT modules is required. Cables with different lengths
can be supplied by Power Integrations. Refer to the “Description & Application Manual for 1SP0635
SCALE-2 IGBT Drivers” for more information.
If the specified value is exceeded, this indicates a driver overload. It should be noted that the driver is
not protected against overload.
Page 5
Min
Typ
9
30
90
9
1
250
700
Typ
Max
Unit
ns
ns
ns
μs
μs
ns
ns
Unit
Ω
Ω
nF
V
V
V
V
V
Unit
400
Min
1050
Max
not assembled
not assembled
not assembled
15
-10.1
-9.8
-9.5
-9
Min
6000
3630
21
20
21
13
Typ
6050
Max
Electrical Isolation
Test voltage (50Hz/1s)
Partial discharge extinction volt.
Creepage distance
6100 V
AC(eff)
V
peak
mm
mm
mm
mm
5)
6)
www.power.com/igbt-driver
京公网安备 11010802033920号
EEWORLD
