Operating Temperature Range ......................... -40°C to +125°C
Storage Temperature Range ............................ -65°C to +150°C
Junction Temperature ......................................................+150°C
Lead Temperature (soldering, 10s) ................................. +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Electrical Characteristics
(V
CC1
= 0.8V to 5.5V, V
CC2
= 0.8V to 5.5V, GND = 0V, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
A
=
+25°C.) (Note 1)
PARAMETER
Supply Voltage
SYMBOL
V
CC
I
CC1
Supply Current
I
CC2
V
CC1
< 5.5V all I/O connections open,
outputs not asserted
V
CC1
< 3.6V all I/O connections open,
outputs not asserted
V
CC2
< 3.6V all I/O connections open,
outputs not asserted
V
CC2
< 2.75V all I/O connections open,
outputs not asserted
L (falling)
M (falling)
T (falling)
S (falling)
V
CC1
Reset Threshold
V
TH1
R (falling)
Z (falling)
Y (falling)
W (falling)
V (falling)
T (falling)
S (falling)
R (falling)
Z (falling)
Y (falling)
W (falling)
V
CC2
Reset Threshold
V
TH2
V (falling)
I (falling)
H (falling)
G (falling)
F (falling)
E (falling)
D (falling)
4.500
4.250
3.000
2.850
2.550
2.250
2.125
1.620
1.530
3.000
2.850
2.550
2.250
2.125
1.620
1.530
1.350
1.275
1.080
1.020
0.810
0.765
CONDITIONS
MIN
0.8
15
10
4
3
4.625
4.375
3.075
2.925
2.625
2.313
2.188
1.665
1.575
3.075
2.925
2.625
2.313
2.188
1.665
1.575
1.388
1.313
1.110
1.050
0.833
0.788
TYP
MAX
5.5
39
28
µA
11
9
4.750
4.500
3.150
3.000
2.700
2.375
2.250
1.710
1.620
3.150
3.000
2.700
2.375
2.250
1.710
1.620
1.425
1.350
1.140
1.080
0.855
0.810
V
V
UNITS
V
www.maximintegrated.com
Maxim Integrated │
2
MAX6715A–MAX6729A/
MAX6797A
Electrical Characteristics (continued)
Dual/Triple, Ultra-Low-Voltage, SOT23 μP
Supervisory Circuits
(V
CC1
= 0.8V to 5.5V, V
CC2
= 0.8V to 5.5V, GND = 0V, T
A
= -40°C to +125°C, unless otherwise noted. Typical values are at T
As shown in the figure below, STM32L15x has 4KB EEPROM. Now, I want to store a char data in it so that it can be read when it is powered on again. How to read and write the EEPROM of STM32L15x? Thank ...
Recently added 430DIY, about designing ultra-low power clockUpload a few external clock ICs and give some brief commentsThe most classic one is of course DS1302, because it is widely used, easy to buy...
[i=s]This post was last edited by qwqwqw2088 on 2020-12-13 17:43[/i]What I want to analyze for you is a Xiaomi wireless charger and Bluetooth speaker. This phone not only supports 50W wired fast charg...
I use Elan's 418N to generate a 20MS cycle, and then use the AD conversion value to adjust the duty cycle. The corresponding cycle value is 137, but the maximum value of 12BIT AD is 4096, which is muc...
I went to the new website and found it was much slower and a lot of information couldn't be opened at all. It was very difficult to find information....
Embedded System
京公网安备 11010802033920号
EEWORLD
