Resistance to sulphur-bearing gas (AS version only): ASTM-B-809
Voltage proof
Volts
Note: A 0.01 Ohm addition to be added to the performance of all resistors <10 Ohms.
ΔR%
ΔR%
ΔR%
ΔR%
ΔR%
1
1
1
0.25
0.25
0.25
500
ΔR%
ΔR%
Maximum
1
0.1
Zero at 155°C
0.1
0.2
0.25
0.05
0.05
0.05
Typical
0.25
0.02
Pulse Performance Data
Pulse Performance Data
Lightning Surge
lightning surge resistors are tested in accordance with IEC 60 115-1 using both 1.2/50µs and 10/700µs pulse shapes. 10 pulses are applied. The limit of
acceptance is a shift in resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Lightning Surge
lightning surge resistors are tested in
accordance with IEC 60 115-1 using
both 1.2/50µs and 10/700µs pulse shapes.
10 pulses are applied. The limit of
acceptance is a shift in resistance of less
than 1% from the initial value.
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
The single impulse graph is the result of 50 impulses of rectangular shape applied at one minute intervals. The limit of acceptance was a shift in
resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Continuous Load Due to Repetitive Pulses
The continuous load graph was obtained by applying repetitive rectangular pulses where the pulse period was adjusted so that the average
power dissipated in the resistor was equal to its rated power at 70°C. Again the limit of acceptance was a shift in resistance of less than 1% from the
initial value
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
My favorite thing to do is to DIY development board. I have not shown the development board in the forum. Let me show the GPRS+GPS development board I made recently. The special feature of this develo...
Big Data Algorithms : https://training.eeworld.com.cn/course/4725The course of Big Data Algorithms aims to teach some basic algorithm design ideas on big data, including probabilistic algorithms, I/O ...
2011 Hot Word: LinuxIn the past, when I was in school, I would try to go around it, but after work, my first job would push me into it.
So began Linux
This was quite tragic - but now I think it has no...
This paper gives a specific method of designing an ISO/IEC15693 card reader using TI's latest RF transceiver chip RI-R6C-001A and a microprocessor. It also introduces the communication protocol of RI-...
Hello, teachers! ! XDS510 burner is ready to burn the out file of chip 2407. How to set it up? In CCS3.3, under tools, there is TMS320LF24XX Flsh programmer. C2000 plug-in has been installed. Please h...
Job Description: 1. Engage in FPGA development of video-related algorithms ; 2. Complete algorithm fixed-point, RTL writing, and board-level debugging; 3. Write design documents and provide correspond...
Today, with the increasing integration of functions, mobile phones can also be used as portable media players (PMP), digital cameras, handheld computers (PDAs), and even global positioning systems ...[Details]
introduction
Throughout the history of automotive lighting, power has always played an important role. Initially, cars only needed headlights to see the road in the dark. Later, other light so...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
The automotive lighting and signal control system is responsible for controlling the vehicle's lighting, signal lights, electric horns, reversing and brake buzzers. Traditional automotive lighting...[Details]
The typical fault troubleshooting listed below is for reference of maintenance personnel.
When the computer is turned on, the indicator light is off and there is no screen display
Mainte...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
I've been studying dot matrix recently. It looks simple, but it takes a while to master it completely! The 8*8 dot matrix hardware circuit I'm making now is like this. The row is driven by 74HC138 + t...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
0 Introduction
High-precision current source can provide high-precision current supply for precision instruments, and is suitable for automatic measurement tasks of various resistors in semico...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]