EEWORLDEEWORLDEEWORLD

Part Number

Search

HCTS161AK

Description
HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16
Categorysemiconductor    logic   
File Size110KB,9 Pages
ManufacturerIntersil ( Renesas )
Websitehttp://www.intersil.com/cda/home/
Download Datasheet Compare View All

HCTS161AK Overview

HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16

HCTS161AMS
September 1995
Radiation Hardened
Synchronous Counter
Pinouts
16 LEAD CERAMIC DUAL-IN-LINE
METAL SEAL PACKAGE (SBDIP)
MIL-STD-1835 CDIP2-T16, LEAD FINISH C
TOP VIEW
MR
CP
P0
P1
P2
P3
PE
GND
1
2
3
4
5
6
7
8
16 VCC
15 TC
14 Q0
13 Q1
12 Q2
11 Q3
10 TE
9 SPE
Features
• 3 Micron Radiation Hardened CMOS SOS
• Total Dose 200K RAD (Si)
• Minimum LET for SEU Upsets: >100 MEV-cm
2
/mg
• Single Event Upset (SEU) Immunity < 2 x 10
-9
Errors/Bit-
Day (Typ)
• Dose Rate Survivability: >1 x 10
12
RAD (Si)/s
• Dose Rate Upset >10
10
RAD (Si)/s 20ns Pulse
• Latch-Up Free Under Any Conditions
• Military Temperature Range: -55 C to +125 C
• Significant Power Reduction Compared to LSTTL ICs
• DC Operating Voltage Range: 4.5V to 5.5V
• Input Logic Levels
-VIL = 0.8V Max
-VIH = VCC/2V Min
• Input Current Levels Ii
5µA at VOL, VOH
o
o
Description
The Intersil HCTS161AMS high-reliability high-speed presettable
four-bit binary synchronous counter features asynchronous reset
and look-ahead carry logic. The HCTS161AMS has an active-low
master reset to zero, MR. A low level at the synchronous parallel
enable, SPE, disables counting and allows data at the preset
inputs (P0 - P3) to load the counter. The data is latched to the
outputs on the positive edge of the clock input, CP. The
HCTS161AMS has two count enable pins, PE and TE. TE also
controls the terminal count output, TC. The terminal count output
indicates a maximum count for one clock pulse and is used to
enable the next cascaded stage to count.
The HCTS161AMS utilizes advanced CMOS/SOS technology to
achieve high-speed operation. This device is a member of
radiation hardened, high-speed, CMOS/SOS Logic Family.
The HCTS161AMS is supplied in a 16 lead Ceramic flatpack
(K suffix) or a SBDIP Package (D suffix).
16 LEAD CERAMIC METAL SEAL
FLATPACK PACKAGE (FLATPACK)
MIL-STD-1835 CDFP4-F16, LEAD FINISH C
TOP VIEW
MR
CP
P0
P1
P2
P3
PE
GND
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC
TC
Q0
Q1
Q2
Q3
TE
SPE
Ordering Information
PART NUMBER
HCTS161ADMSR
HCTS161AKMSR
HCTS161AD/Sample
HCTS161AK/Sample
HCTS161AHMSR
TEMPERATURE RANGE
-55
o
C to +125
o
C
-55
o
C to +125
o
C
+25
o
C
+25
o
C
+25
o
C
SCREENING LEVEL
Intersil Class S Equivalent
Intersil Class S Equivalent
Sample
Sample
Die
PACKAGE
16 Lead SBDIP
16 Lead Ceramic Flatpack
16 Lead SBDIP
16 Lead Ceramic Flatpack
Die
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
Spec Number
File Number
1
518888
2144.2

HCTS161AK Related Products

HCTS161AK HCTS161AD HCTS161AHMSR HCTS161AKMSR HCTS161ADMSR HCTS161AMS
Description HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16 HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16 HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16 HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, CDFP16, CERAMIC, DFP-16 HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, CDIP16 HCT SERIES, SYN POSITIVE EDGE TRIGGERED 4-BIT UP BINARY COUNTER, UUC16
Questions about msp430
I'm learning msp430f5438 recently. After installing IAR, I found that there is no header file for 5438 in the header file. For example, registers such as TACTL and TAR cannot be recognized. Is it beca...
tm890912 Microcontroller MCU
CP2201 Issues
Hello everyone, I used 8051 and CP2201 to make an Ethernet interface. During the initialization of the CP2201 physical layer, the value of INT1RD is always 0X31 regardless of whether it is connected o...
cqwjfb MCU
Automatic Wire Winding Tool Specctra Guide
Very good @ Share it with everyone...
dykonka PCB Design
Some thoughts on interference in industrial environments
In many cases, we have to talk about anti-interference. Where does the interference come from? I personally think that 30% of the devices that are interfered with are caused by power supply interferen...
aone2008 Industrial Control Electronics
Excuse me, can rom be set in cpld?
Excuse me, can rom be set in cpld?I have seen FPGAs, but I don't know how CPLDs are....
qchpanna FPGA/CPLD
How to generate lib files under TC
Hello experts, I want to write a LIB file in TC, but I don't know how to start. What is the format of the LIB file? I hope you can give me some advice. It would be best if you have examples. Thank you...
nlinger Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1351  1775  2783  423  1473  28  36  57  9  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号