EEWORLDEEWORLDEEWORLD

Part Number

Search

MCP130T-315DI

Description
Microcontroller Supervisory Circuit with Open Drain Output
File Size157KB,16 Pages
ManufacturerMicrochip
Websitehttps://www.microchip.com
Download Datasheet View All

MCP130T-315DI Overview

Microcontroller Supervisory Circuit with Open Drain Output

MCP120/130
Microcontroller Supervisory Circuit with Open Drain Output
FEATURES
• Holds microcontroller in reset until supply voltage
reaches stable operating level
• Resets microcontroller during power loss
• Precision monitoring of 3V, 3.3V and 5V systems
• 7 voltage trip points available
• Active low RESET pin
• Open drain output
• Internal pull-up resistor (5 kΩ) for MCP130
• Holds RESET for 350 ms (typical)
• RESET to V
CC
= 1.0V
• Accuracy of ±125 mV for 5V systems and ±75 mV
for 3V systems over temperature
• 45
µA
typical operating current
• Temperature range:
- Industrial (I): -40°C to +85°C
PACKAGES
TO-92 with
‘D’ Bondout
TO-92 WITH
‘F’ BONDOUT
RST
V
SS
V
DD
V
SS
V
DD
RST
MCP120
MCP130
MCP130
TO-92 with
‘G’ Bondout
TO-92 with
‘H’ Bondout
DESCRIPTION
The Microchip Technology Inc. MCP120/130 is a volt-
age supervisory device designed to keep a microcon-
troller in reset until the system voltage has reached the
proper level and stabilized. It also operates as protec-
tion from brown-out conditions when the supply voltage
drops below a safe operating level. Both devices are
available with a choice of seven different trip voltages
and both have open drain outputs. The MCP130 has an
internal 5 kΩ pullup resistor. Both devices have active
low RESET pins. The MCP120/130 will assert the
RESET signal whenever the voltage on the V
DD
pin is
below the trip-point voltage.
V
DD
V
SS
RST
V
DD
V
SS
MCP120
RST
MCP120
MCP130
150mil SOIC
RST
V
DD
NC
V
SS
1
2
3
4
8
7
6
5
NC
NC
NC
NC
SOT-23-3
RST
V
DD
V
SS
MCP120
MCP130
MCP120
MCP130
BLOCK DIAGRAM
V
DD
5k
internal
pull-up on
MCP130
only
RESET
Comparator
+
-
Delay
Circuit
Output
Driver
Bandgap
Reference
2001 Microchip Technology Inc.
DS11184D-page 1
ADCLO of 2812
If I use the internal ADC of 2812, how should I connect the ADCLO pin? Should I connect it to the analog ground?...
wj54321 Microcontroller MCU
SensorTile.box Trial (3) Expert Mode Trial
[i=s]This post was last edited by symic on 2020-4-26 18:56[/i]According to the tutorial, today we will start to experience the expert mode. The expert mode allows us to customize the use of sensors an...
symic ST MEMS Sensor Creative Design Competition
System Control Documentation
Share learning materials with everyone to enrich everyone’s learning resources!...
wulei19880906 Microcontroller MCU
Application of TFT LCD screen in oscilloscope
If you have any related sample programs, please send me an email at caoyi_027@163.com...
gxkj001 DIY/Open Source Hardware
Create a new component MP2225 in Multisim8
Is it possible to create a new component in Multisim8 without ***.sym and ***.cir files? Where can I find these two files?...
背后捡小菜 Analog electronics
MSP430F5438A burnout problem
[color=#666666][font=arial, 宋体] MSP430F5438A suddenly burned out during use. It was powered by LDO. It was connected to the computer's serial port and the oscilloscope ground wire at the time. The sim...
a3213211353 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2507  2846  1904  222  2240  51  58  39  5  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号