September, 12th 2011
Automotive grade
AUIPS6011(
S
)(
R
)
INTELLIGENT POWER HIGH SIDE SWITCH
Features
Over temperature shutdown (with auto-restart)
Short circuit protection (current limit)
Reverse battery protection (turns On the MOSFET)
Full diagnostic capability (short circuit to battery)
Active clamp
Open load detection in On and Off state
Ground loss protection
Logic ground isolated from power ground
ESD protection
Lead Free and RoHS compliant
Product Summary
Rds(on)
Vclamp
I Limit
Open load
Packages
14m max.
39V
60A
3V / 2.4A
Description
The AUIPS6011(S)(R) is a five terminal Intelligent Power
Switch (IPS) for use in a high side configuration. It features
short circuit, over-temperature, ESD protection, inductive load
capability and diagnostic feedback. The output current is
limited to the Ilim value. The current limitation is activated until
the thermal protection acts. The over-temperature protection
turns off the device if the junction temperature exceeds the
Tshutdown value. It will automatically restart after the junction
has cooled 7°C below the Tshutdown value. The reverse
battery protection turns On the MOSFET. A diagnostic pin
provides different voltage levels for each fault condition. The
double level shifter circuitry will allow large offsets between
the logic and load ground.
TO-220
AUIPS6011
D²Pak
AUIPS6011S
D-Pak
AUIPS6011R
Typical Connection
+5V
+Bat
Vcc(3)
Dg(4)
Control
Rdgs
In(2)
V Diag
Rin
Input Signal
Load
Gnd(1)
Out(5)
Pull-up resistors required for
open load off and short
circuit to Vbat detection
Rdgp
www.irf.com
1
AUIPS6011(
S
)(
R
)
Qualification Information
†
Qualification Level
Automotive
††
(per AEC-Q100 )
Comments: This family of ICs has passed an Automotive qualification. IR’s
Industrial and Consumer qualification level is granted by extension of the higher
Automotive level.
MSL1, 260°C
D2PAK-5L
(per IPC/JEDEC J-STD-020)
TO-220
DPAK-5L
Machine Model
Human Body Model
ESD
Charged Device Model
(DPAK,D2PAK)
Charged Device Model
(TO220)
Not applicable
(non-surface mount package style)
MSL1, 260°C
(per IPC/JEDEC J-STD-020)
Class
M2 (+/-150V)
(per AEC-Q100-003)
†††
Class
H1C (+/-1500V)
(per AEC-Q100-002)
†††
Class
C4 (+/-900V)
(per AEC-Q100-011)
†††
Class
C3B (+/-750V)
(per AEC-Q100-011)
Class
II,
Level
A
(per AEC-Q100-004)
Yes
†††
Moisture Sensitivity Level
IC Latch-Up Test
RoHS Compliant
†
††
†††
Qualification standards can be found at International Rectifier’s web site
http://www.irf.com/
Exceptions to AEC-Q100 requirements are noted in the qualification report.
Passing voltage level
www.irf.com
2
AUIPS6011(
S
)(
R
)
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters
are referenced to Ground lead. Tj= -40°C..150°C, Vcc=6..35V (unless otherwise specified).
Symbol
Vout
Voffset
Vin
Vcc max.
Vcc cont.
Vcc sc.
Iin max.
Idg max.
Vdg
Pd
Tj max.
Tsoldering
Parameter
Maximum output voltage
Maximum logic ground to load ground offset
Maximum input voltage
Maximum Vcc voltage
Maximum continuous Vcc voltage
Maximum Vcc voltage with short circuit protection
Maximum IN current
Maximum diagnostic output current
Maximum diagnostic output voltage
Maximum power dissipation (internally limited by thermal protection)
Rth=5°C/W AUIPS6011
Rth=40°C/W AUIPS6011S 1”sqrt. footprint
Rth=50°C/W AUIPS6011R 1”sqrt. footprint
Max. storage & operating temperature junction temperature
Soldering temperature (10 seconds)
Min.
Max.
Units
Vcc-35 Vcc+0.3
Vcc-35 Vcc+0.3
-0.3
5.5
36
28
24
-3
10
-3
10
-0.3
5.5
V
mA
V
W
°C
°C
-40
25
3.1
2.5
150
300
Thermal Characteristics
Symbol
Rth1
Rth2
Rth1
Rth2
Rth3
Rth1
Rth2
Rth3
Parameter
Thermal resistance junction to ambient AUIPS6011 TO220 free air
Thermal resistance junction to case AUIPS6011 TO220
Thermal resistance junction to ambient AUIPS6011S D²Pak std. footprint
Thermal resistance junction to ambient AUIPS6011S D²Pak 1” sqrt.
Footprint
Thermal resistance junction to case AUIPS6011S D²Pak
Thermal resistance junction to ambient AUIPS6011R D-Pak std. footprint
Thermal resistance junction to ambient AUIPS6011R D-Pak 1” sqrt.
Footprint
Thermal resistance junction to case AUIPS6011R D-Pak
Typ.
50
1.2
60
40
1.2
70
50
1.2
Max.
Units
°C/W
Recommended Operating Conditions
These values are given for a quick design. For operation outside these conditions, please consult the application notes.
Symbol
VIH
VIL
Iout
Parameter
High level input voltage
Low level input voltage
Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V
Rth=5°C/W IPS6011
Rth=40°C/W IPS6011S 1” sqrt. footprint
Rth=50°C/W IPS6011R 1” sqrt. footprint
Recommended resistor in series with IN pin
Recommended resistor in series with DG pin for reverse battery protection
Recommended pull-up resistor for DG
Recommended pull-up resistor for open load detection
Max. switching frequency
Min.
4
0
Max.
5.5
0.9
18
6.3
5.6
10
20
20
100
0.3
Units
A
Rin
Rdgs
Rdgp
Rol
F max.
4
4
4
5
k
kHz
www.irf.com
3
AUIPS6011(
S
)(
R
)
Static Electrical Characteristics
Tj=-40°C..150°C, Vcc=6..28V (unless otherwise specified), typical values are given for Vcc=14V and Tj=25°C
Symbol
Rds(on)
Parameter
ON state resistance Tj=25°C
ON state resistance Tj=150°C
ON state resistance Tj=25°C, Vcc=6V
ON state resistance during reverse battery
Tj=25°C
Operating voltage range with short circuit
protection
Vcc to Out clamp voltage 1
Vcc to Out clamp voltage 2
Supply current when Off and Vout
connected to ground with R<4Ω
Supply current when On
Input high threshold voltage
Input low threshold voltage
Input hysteresis
Input current when device is On
Dg leakage current
Low level DG voltage
Min.
Typ.
11
19.5
12
15
Max.
14
25
17
20
24
43
Units
m
Test Conditions
Vin=5V, Iout=20A
Vin=5V, Iout=20A
Vin=5V, Iout=20A
Vcc-Gnd=-14V
Vcc op.
V clamp 1
V clamp 2
Icc Off
Icc On
Vih
Vil
In hyst.
Iin On
Idg
Vdg
6
36.5
39
40
4
2.2
2.5
2
0.5
40
0.1
0.25
V
9
5
3
µA
mA
V
µA
V
Iout=50mA
Iout=16A (see Fig. 1)
Vin=0V, Vout=0V,
Tj=25°C, Vcc=14V
Vin=5V, Vcc=14V
1.5
0.2
1
100
10
0.4
Vin=5V
Vdg=5V
Idg=1.6mA
Switching Electrical Characteristics
Vcc=14V, Resistive load=6, Vin=5V, Tj=-40°C..150°C, typical values are given for Tj=25°C
Symbol
Tdon
Tr1
Tr2
Parameter
Turn-on delay time
Rise time to Vout=Vcc-5V
Rise time to Vout=0.9 x Vcc
Tj=-40°C..25°C
Tj=25°C..150°C
Turn On dV/dt
Turn On energy
Turn-off delay time
Fall time to Vout=0.1 x Vcc
Turn Off dV/dt
Turn Off energy
Min.
Typ.
30
25
80
40
0.3
4
70
30
0.7
1.5
Max.
80
80
300
100
Units
µs
Test Conditions
dV/dt (On)
EOn
Tdoff
Tf
dV/dt (Off)
EOff
V/µs
mJ
µs
V/µs
mJ
see Fig. 3
150
80
www.irf.com
4
AUIPS6011(
S
)(
R
)
Protection Characteristics
Tj=-40°C..150°C, Vcc=6..28V (unless otherwise specified), typical values are given for Vcc=14V and Tj=25°C
Symbol
Ilim
Tsd+
Tsd-
Vsc
UV+
UV -
VOL Off
I OL On
Parameter
Internal current limit
Over temperature high threshold
Over temperature low threshold
Short-circuit detection voltage(2)
Under voltage protection Vcc going up
Under voltage protection Vcc going down
Open load detection threshold
Open load detection threshold
Min.
35
150(1)
Typ.
60
165
158
3
5
4.5
3
2
1.6
Max.
85
Units
A
°C
Test Conditions
Vout=0V, Tj=25°C
See fig. 2
2
2
0.5
0.5
4
6.2
5.8
4
3
2.4
V
Tj=-40..25°C
Tj=25..150°C
A
(1) Guaranteed by design
(2) Reference to Vcc
True Table
Operating Conditions
IN
OUT
DG
Normal
H
H
H
Normal
L
L
H
Open Load
H
H
L
Open Load (3)
L
H
L
Short circuit to Gnd
H
L
L
Short circuit to Gnd
L
L
H
Short circuit to Vcc
H
H
L (4)
Short circuit to Vcc (5)
L
H
L
Over-temperature
H
L
L
Over-temperature
L
L
H
(3) With a pull-up resistor connected between the output and Vcc.
(4) Vds lower than 10mV.
(5) Without a pull-up resistor connected between the output and Vcc.
Lead Assignments
www.irf.com
5
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
