3HSR57-B-T-FREQ datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> 3HSR57-B-T-FREQ

3HSR57-B-T-FREQ: DescriptionSine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN; CategoryPassive components oscillator; File Size162KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric View All

3HSR57-B-T-FREQ Overview

Sine Output Oscillator, 10MHz Min, 30MHz Max, ROHS COMPLIANT, SMD, 4 PIN

3HSR57-B-T-FREQ Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	Euroquartz
Reach Compliance Code	compliant
Other features	ENABLE/DISABLE FUNCTION
Frequency Adjustment - Mechanical	NO
frequency stability	50%
Installation features	SURFACE MOUNT
Maximum operating frequency	30 MHz
Minimum operating frequency	10 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	SINE
Output impedance	10000 Ω
Output level	1 V
physical size	7.0mm x 5.0mm x 1.8mm
Nominal supply voltage	3 V
surface mount	YES
Base Number Matches	1

Preview

Download Datasheet

View All

EURO

QUARTZ

7 x 5 x 1.8mm SMD

FEATURES

Sine Wave output in small SMD package

Output 10k //10pF load, level 1.0V peak to peak

Harmonics -25dBc maximum

Very low current consumption <1.0mA at 2.8V supply

HSR57 Sine Wave Oscillators

10.0MHz to 30.0MHz

OUTLINE & DIMENSIONS

DESCRIPTION

HSR57 sine wave clock oscillators provide a true sine wave out output

while being packaged in the industry-standard, 7 x 5mm SMD outline

package. The oscillator is capable of being produced with close

tolerances and exhibits low current consumption.

SPECIFICATION

Frequency Range:

Input Voltage:

Output Wave Form:

Frequency Stability

Commercial 0~70°C:

Industrial -40 ~+85°C:

Output Level:

Harmonics:

Phase Noise:

Current Consumption

Supply 2.8 VDC:

Supply 3.3 VDC:

Supply 5.0 VDC:

Start-up Time:

Storage Temperature:

Sub-Harmonics:

Ageing:

Enable/Disable Option:

Disable time:

10.0MHz to 30.0MHz

+2.8 VDC, +3.3 VDC or +5.0 VDC

True sine wave

±25ppm, ±50ppm or ±100ppm*

10kW//10pF load, level 1.0V p-p

-25dBc maximum

-130 dBC/Hz at 1kHz offset

1.0mA

1.1mA

1.2mA

2.0ms typical

-55° to +125°C

None

±5ppm/year

Output is high impedance when pad 1

is taken LOW.

150ns maximum

(Add 'T' to the part number code for

this option.)

Fully compliant

SOLDER TEMPERATURE PROFILE

RoHS Status:

Non-standard frequency stability is available, check with sales.

PART NUMBERING

Example:

Supply Voltage

28 = 2.8 Volts

3 = 3.3 Volts

5 = 5.0 Volts

Series Designation HSR57

Stability

A = ±25ppm 0° to +70°C

B = ±50ppm 0° to +70°C

C = ±100ppm 0° to +70°C

D = ±25ppm -40° to +85°C

E = ±50ppm -40° to +85°C

F = ±100ppm -40° to +85°C

Enable/Disable Option

Blank = Not implemented

T = Option implemented

Frequency

Customer-Specific Code

(Included

if specified by

engineering department.)

3HSR57-B-T-25.000-X

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

Four-phase full-wave brushless motor drive control circuit

Voice controlled backup lighting circuit

Current fed push-pull inverter circuit diagram

switching circuit

collector amplitude modulation circuit

A 12-in-1 remote control circuit, the IC is EM78P156

[Help] How to find the angle from the tangent of an angle: I would like to ask:How to calculate the angle from the tangent value of an angle?Can such an algorithm be implemented using a single chip microcomputer?Thank you...; maq9627 Microcontroller MCU

Using multisim microcontroller simulation, header file problem: I'm learning to use multisim software to learn MCU recently, but I encountered some difficulties when using multisim to simulate MCU. The MCU simulation chip I used is "MCU MODULE--805x--8051", and I ...; 扫把鑫 51mcu

Guess what will happen in the magnification category of this year’s competition?: [i=s]This post was last edited by paulhyde on 2014-9-15 03:34[/i] I am also planning to participate in an electronic design competition this year, and I am planning to make an amplifier. I don't know ...; 给力王海潮A Electronics Design Contest

[EEWORLD 32nd] Community star figures for November 2011 are announced!: Thank you all for your hard work for the forum. Here we select some friends who have made outstanding contributions in November!Outstanding Moderator of NovemberForum IDResponsible sectionReason for w...; EEWORLD社区 Suggestions & Announcements

Workplace joke: The most miserable interviewer: Workplace joke: The most miserable interviewerThe company I had my first interview with was Microsoft.Examiner: What is the retail price of Windows 7 Professional in mainland China?Me: 5 yuan. Examine...; zhandetian Talking

A large number of EP1C6 schematic files are provided for your reference when studying!: A large number of EP1C6 schematic files are provided for your reference when studying!...; liulong2007 FPGA/CPLD

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components