The UT54ACS153 and the UT54ACTS153 are dual four to one
line selectors/multiplexers. Common inputs A and B select a
value from one of four sources for each section and routes the
value from each section to their respective outputs. Separate
strobe inputs, G are provided for each of the two four-line sec-
tions.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
SELECT
INPUTS
B
X
L
L
L
L
H
H
H
H
A
X
L
L
H
H
L
L
H
H
C0
X
L
H
X
X
X
X
X
X
DATA INPUTS
C1
X
X
X
L
H
X
X
X
X
C2
X
X
X
X
X
L
H
X
X
C3
X
X
X
X
X
X
X
L
H
OUTPUT
CONTROL
G
H
L
L
L
L
L
L
L
L
OUTPUT
Y
L
L
H
L
H
L
H
L
H
PINOUTS
16-Pin DIP
Top View
1G
B
1C3
1C2
1C1
1C0
1Y
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
A
2C3
2C2
2C1
2C0
2Y
16-Lead Flatpack
Top View
1G
B
1C3
1C2
1C1
1C0
1Y
V
SS
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
DD
2G
A
2C3
2C2
2C1
2C0
2Y
LOGIC SYMBOL
A
B
1G
1C0
1C1
1C2
1C3
(14)
(2)
(1)
(6)
(5)
(4)
(3)
EN
0
1
2
3
MUX
(7)
0
1
0
-
G
--
3
1Y
(15)
2G
(10)
2C0
(11)
2C1
(12)
2C2
(13)
2C3
(9)
2Y
Note:
1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and IEC
Publication 617-12.
1
LOGIC DIAGRAM
OUTPUT
CONTROL
1G
(1)
1C0 (6)
(5)
(7)
1C1
DATA 1
1C2
1Y
(4)
1C3
(3)
B
SELECT
(2)
A (14)
2C0
(10)
2C1 (11)
DATA 2
2C2
(12)
(9)
2Y
2C3
(13)
OUTPUT
CONTROL
2G
(15)
2
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
3
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
I
DDQ
C
IN
C
OUT
Quiescent Supply Current
Input capacitance
5
Output capacitance
5
V
DD
= 5.5V
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
10
15
15
μA
pF
pF
2.1
1.6
mW/
MHz
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
0.40
0.25
V
V
OH
V
I
OS
I
OL
mA
mA
4
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
As the title says, the input signal of a Class D audio amplifier chip is required to be a PWM signal. How to encode the audio signal into PWM? What is the encoding rule? Here are two schematic diagram...
As shown in the figure, a resistor and capacitor circuit is connected to the audio output of the power amplifier. Is this just a pull-down function? Are there other functions? Please explain, please g...
My thesis topic is the design of a light bulb optometry controller, which is to measure the current of the light bulb to determine whether the light bulb is good or bad. The current is about 10A and t...
[i=s]This post was last edited by pomin on 2022-4-3 14:24[/i]CH582 USB HOST Code Interpretation
The feature of CH582 MCU is Bluetooth, so I plan to make a small device that can convert a wired keyboar...
Recently, I have a task at work that requires calculating the wire diameter of the wire harness and corresponding to the US standard AWG wire number. I would like to share the conversion method and us...
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
1. Project Overview
1.1 Introduction
Currently, most music files are saved in MP3 format, a lossy audio compression format that cannot perfectly reproduce the original music. With the exp...[Details]
The structure of an LCD TV primarily consists of the LCD display module, power module, driver module (primarily including the main driver board and tuner board), and keypad module. LCD display modu...[Details]
Since the beginning of this year, price wars have intensified, new models have been launched one after another, used cars with zero kilometers have become a hot topic, and the industry's internal c...[Details]
Smartphones have become essential digital devices, and the growing number of smartphone-centric applications is enriching people's lives. As users, they desire a better app experience and a wider r...[Details]
While the current industry consensus is that autonomous vehicles are robots and that their systems are managed using robotics-developed thinking, there are also cases where autonomous driving is ac...[Details]
Comparison instructions compare two numbers, IN1 and IN2, of the same data type. IN1 and IN2 are located above and below the contact, respectively, and their data types must be the same. Operands c...[Details]
Bourns®
PEC04
, PEC05, and PEC06 model series, with IP40 protection rating, provide a rugged, space-saving position sensing solution for a variety of electronic devices.
August 1...[Details]
In 1799, Alessandro Volta demonstrated electrical energy storage technology; a century later, Guglielmo Marconi proved that radio waves could transmit across oceans.
The IEEE ...[Details]
Introduction
With the development of multimedia, music players, as consumer electronics products, are facing growing demand, prompting manufacturers to adopt more advanced technologies to enh...[Details]
On August 14, Zhiyuan Robotics released the industry's first open source platform for robot world models - Genie Envisioner.
Zhiyuan Robotics has launched Genie Envisioner (GE), a unifie...[Details]
The mobile computing model pioneered by smartphones has dramatically changed users' understanding of computer usage, and they are increasingly reliant on mobile computing technology to navigate the...[Details]
PCI Express is a system interconnect interface standard developed from PCI. While PCI and PCI-X are both based on 32-bit and 64-bit parallel buses, PCI Express uses a high-speed serial bus. PCI Exp...[Details]
On August 13, Elon Musk confirmed on the 10th of this month that although he closed the independent Dojo chip project, the successor to the Dojo 2 data center-level AI chip "Dojo 3" planned to be m...[Details]
According to the "Automotive Industry Investment Management Regulations" issued by the National Development and Reform Commission, the regulations clearly state that "extended-range electric vehicl...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
