EEWORLDEEWORLDEEWORLD

Part Number

Search

3PMT43CE3

Description
Trans Voltage Suppressor Diode, 1500W, 43V V(RWM), Bidirectional, 1 Element, Silicon, PLASTIC PACKAGE-3
CategoryDiscrete semiconductor    diode   
File Size80KB,3 Pages
ManufacturerMicrosemi
Websitehttps://www.microsemi.com
Download Datasheet Parametric View All

3PMT43CE3 Overview

Trans Voltage Suppressor Diode, 1500W, 43V V(RWM), Bidirectional, 1 Element, Silicon, PLASTIC PACKAGE-3

3PMT43CE3 Parametric

Parameter NameAttribute value
MakerMicrosemi
package instructionR-PSSO-G2
Reach Compliance Codecompliant
ECCN codeEAR99
Minimum breakdown voltage47.8 V
ConfigurationSINGLE
Diode component materialsSILICON
Diode typeTRANS VOLTAGE SUPPRESSOR DIODE
JESD-30 codeR-PSSO-G2
Maximum non-repetitive peak reverse power dissipation1500 W
Number of components1
Number of terminals2
Package body materialPLASTIC/EPOXY
Package shapeRECTANGULAR
Package formSMALL OUTLINE
polarityBIDIRECTIONAL
Maximum repetitive peak reverse voltage43 V
surface mountYES
technologyAVALANCHE
Terminal formGULL WING
Terminal locationSINGLE
Base Number Matches1
3PMT5.0 thru 3PMT170
POWERMITE
1500 Watt Transient Absorption Zener
®
SCOTTSDALE DIVISION
DESCRIPTION
These 1500 watt transient voltage suppressors offer power-handling capabilities only
found in larger packages. They are most often used for protecting against transients
from inductive switching environments or induced secondary lightning effects as
found in lower surge levels of IEC61000-4-5. With very fast response times, they are
also effective in protection from ESD or EFT. Powermite
®
package features include a
full metallic bottom that eliminates the possibility of solder-flux entrapm ent during
assembly. They also provide unique locking tab acting as an integral heat sink. With
its very short terminations, parasitic inductance is minimized to reduce voltage
overshoots during fast-rise-time transients
.
IMPORTANT:
For the most current data, consult
MICROSEMI’s
website:
http://www.microsemi.com
POWERMITE
®
WWW.
Microsemi
.
COM
FEATURES
Very low profile surface mount package (1.1mm)
Integral heat sink-locking tabs
Compatible with automatic insertion equipment
Full metallic bottom eliminates flux entrapment
Voltage range 5 volts to 170 volts
Available in both unidirectional or bi-directional
(C suffix for bi-directional)
APPLICATIONS / BENEF ITS
Secondary lightning transient protection
Inductive switching transient protection
Small footprint
Very low parasitic inductance for minimal
voltage overshoot
Compliant to IEC61000-4-2 and IEC61000-4-4 for
ESD and EFT protection respectively and
IEC61000-4-5 for surge levels defined herein
MAXIMUM RATINGS
Operating Temperature: -55°C to +150°C
Storage Temperature: -55°C to +150°C
1500 Watt peak pulse power (10 / 1000 µsec.)
Forward Surge Current: 200 Amps (8.3 ms)
(excluding bidirectional)
Repetition surge rate (duty factor): 0.01%
Lead and mounting temperature: 260°C for 10 sec
MECHANICAL AND PACKAGING
Terminals tin-lead plated
Two-lead side internally connected together
Cathode designated with band (unidirectional)
Molded epoxy package meets UL94V-0
Weight: 0.072 grams (approximate)
Thermal resistance: 2.5°C / watt junction to tab
130°C / watt junction to ambient with
recommended footprint
Tape & Reel packaging per EIA-481-2
(16 mm - 6000 units/reel)
P E A K P U L S E P O W E R R A TI N G S
P
pp
– Peak Pulse Power – kW
Peak Pulse Power (P
pp
) or Current (I
pp
)
in percent of 25º C rating
100
100
75
50
25
0
0
50 100 150 200
10
3PMT
1.0
.10
100ns
1µs
10µs
100µs
1ms
10ms
t
d
– Pulse Time – sec
Copyright
©
2001
MSCXXXX.PDF 09-09 2002 REV 0
T – Temperature – ºC
Page 1
Microsemi
Scottsdale Division
8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503
How to filter out 50HZ power frequency interference introduced by active filtering
I need to amplify a sine wave signal of about 1mV to collect its frequency. I use AD620+active bandpass filter+OP07 amplification for signal acquisition. At present, after the second-level active filt...
天天1 Analog electronics
Is it the inverter or the integrator circuit?
As shown The input Uin of the op amp is obtained from the -380VDC bus through resistor voltage division to obtain -3.5VDC Is the op amp in the figure a simple inverting 1:1 amplifier circuit, or is it...
shaorc Analog electronics
How to configure uclinux to automatically obtain an ip after arm is powered on?
How to configure uclinux to let arm automatically get ip after power on? My development board is S3C44B0. I heard that uclinux supports dhcp. 1. What should I choose when compiling uclinux 2.4 kernel ...
wawj1819 Linux and Android
Can first-tier devices do the job?
Previously, the sensor head was made by Honeywell combined with first-line devices. The SHT21 may be smaller in size. The I2C interface direct cable transmission requires signal preprocessing. Can fir...
bjwl_6338 DIY/Open Source Hardware
linux-2.6.34 kernel porting documentation [simple operation]
I just transplanted the kernel image file, put it on the development board and ran it for a while, and the system is running!!! Pictures speak louder than words...See the attached documentation for th...
37°男人 Embedded System
Introduction to the training for the 2013 Electronic Design Competition
[i=s] This post was last edited by paulhyde on 2014-9-15 03:11 [/i] Nanhua University Huang Zhiwei prepares for the 2013 Electronic Design Competition - Introduction to some information on training...
黄智伟 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1821  730  1996  2243  2242  37  15  41  46  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号