EEWORLDEEWORLDEEWORLD

Part Number

Search

3U8710NC0

Description
THUMB/PUSHWHEEL SWITCH-8SWITCHES, BINARY CODED HEXADECIMAL, 0.1A, 28VDC, THROUGH HOLE-STRAIGHT, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size129KB,5 Pages
ManufacturerC&K
Environmental Compliance
Download Datasheet Parametric View All

3U8710NC0 Overview

THUMB/PUSHWHEEL SWITCH-8SWITCHES, BINARY CODED HEXADECIMAL, 0.1A, 28VDC, THROUGH HOLE-STRAIGHT, ROHS COMPLIANT

3U8710NC0 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerC&K
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPANEL MOUNTABLE
body width15.8 mm
body height17.4 mm
Body length or diameter60.96 mm
Maximum contact current (DC)0.1 A
Contact (DC) maximum rated R load.1A@28VDC
Maximum contact voltage (DC)28 V
Electrical life1000000 Cycle(s)
Manufacturer's serial number3U
Installation featuresTHROUGH HOLE-STRAIGHT
Number of positions16
Number of switching segments8
Maximum operating temperature65 °C
Minimum operating temperature-10 °C
surface mountNO
switch functionBINARY CODED HEXADECIMAL
Switch typeTHUMB/PUSHWHEEL SWITCH
Termination typeSOLDER
Base Number Matches1
3U Series
Tiny Pushwheel Switches
Features/Benefits
Tiny size saves space
10 and 16 position models available
ESD clip available on select models
Snap-in front mount saves assembly time
Typical Applications
Computer peripherals
Test equipment
Instrumentation
Specifications
CONTACT RATING:
CARRY: 1 AMP continuous.
SWITCH: 0.4 VA max., 100 mA max., 28 V DC max.
OPERATING VOLTAGE: 50 mV to 28 V DC.
ELECTRICAL LIFE: 1,000,000 actuations.
CONTACT RESISTANCE: Below 300 m
typ. @
2-4 V DC, 100 mA.
INSULATION RESISTANCE: 109
min. (dry).
DIELECTRIC STRENGTH: 500 Vrms min. @ sea level
between common terminal and any output.
OPERATING TEMPERATURE: –10ºC to 65ºC.
Materials
HOUSING: Polyester (UL 94V-0).
PUSHWHEEL: Polycarbonate.
PUSHBUTTON: Polyester (UL 94V-0).
ROTOR CONTACTS: Gold over nickel over copper alloy.
STATOR CONTACTS: Hard gold over nickel over copper on epoxy
fiberglass.
NOTE:
Specifications and materials listed above are for switches with standard options.
For information on specific and custom switches, consult Customer Service Center.
Note: All models listed are RoHS compliant. See Technical Data section of this catalog for
RoHS compliant and compatible definitions and specifications.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages N–4 thru N–6. For additional options not shown in catalog, consult Customer Service Center.
Consult factory for illumination availability.
Thumbwheel & Pushwheel
Series
3U
Tiny pushwheel
Number of Sections
0
Switch section
Function Code
1
1 Switch section
21
BCD 1-2-4-8
2
2 Switch sections
71
BCH, 16 position
3
3 Switch sections
4
4 Switch sections
5
5 Switch sections
6
6 Switch sections
7
7 Switch sections
8
8 Switch sections
9
More than 8 switch sections
Mounting Style
0
Snap-in, front mount
Terminations
0
Short PC board
N
Short PC board with pins*
9
Any combination
Dust Lens
0
No lens
2
Dust lens
Color/Marking/Stops
0
Matte black housing, gloss black wheel, extended actuator, white vertical characters, black pushbutton, no stops
9
Combination of body colors, wheel colors, marking and/or stops
A
Matte black housing, gloss black wheel, extended actuator, white horizontal characters, black pushbutton, no stops
C
Matte black housing, gloss black wheel, recessed actuator, white vertical characters, black pushbutton, no stops
E
Matte black housing, gloss black wheel, recessed actuator, white horizontal characters, black pushbutton, no stops
N
* Note: Termination option N (RoHS compliant) replaces termination option 3 (non-RoHS compliant).
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
N–3
www.ck-components.com
MPLAB X IDE4.35 header file problem
Why are these two registers not recognized?...
测控一哥 Microchip MCU
How to set the GPIO of 811 board so that it can be used as both input and output
How to set GPIO so that it can be used as both input and output? My PB port needs to be in output mode when writing data to the chip, and in input mode when reading data from the chip. How can I set i...
jinghong21 Microcontroller MCU
Bridge push-pull power amplifier circuit
Bridge push-pull power amplifier circuitIn order to achieve single power supply without transformer and large capacitor, a bridge push-pull power amplifier circuit, referred to as BTL circuit , can be...
fighting Analog electronics
Looking for a design solution for a programmable amplifier (gain)!
[i=s] This post was last edited by dontium on 2015-1-23 12:59 [/i] You can choose the parameters yourself. TI devices are preferred. I mainly want to learn the principles. Various materials are also f...
zhangchaoqun Analogue and Mixed Signal
TSSOP package PCB drawing distance
Dear teachers, the picture below is a TSSOP-16 package. When drawing the PCB, it prompts that the distance is less than 10mil. Is this because the package library is wrong? The package library is down...
萤火 PCB Design
SPMC75 realizes AC variable frequency drive control
Abstract: Variable frequency drive technology has penetrated into every corner of our lives, such as variable frequency air conditioners, refrigerators, washing machines and other home appliances. Now...
rain MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2630  1032  1238  2720  239  53  21  25  55  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号