The UT54ACS4002 and the UT54ACTS4002 are dual 4-input
NOR gates. A high on any input forces the output to a low state.
The circuits perform the Boolean functions:
Y = A + B + C + D = A⋅B⋅C⋅D.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUTS
An
L
H
X
X
X
Bn
L
X
H
X
X
Cn
L
X
X
H
X
Dn
L
X
X
X
H
OUTPUT
Yn
H
L
L
L
L
PINOUTS
14-Pin DIP
Top View
Y1
A1
B1
C1
D1
NC
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
Y2
D2
C2
B2
A2
NC
14-Lead Flatpack
Top View
Y1
A1
B1
C1
D1
NC
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
Y2
D2
C2
B2
A2
NC
LOGIC DIAGRAM
LOGIC SYMBOL
A1
B1
C1
D1
A2
B2
C2
D2
Y1
Y2
A1
B1
C1
D1
A2
B2
C2
D2
(2)
(3)
(4)
(5)
(9)
(10)
(11)
(12)
≥1
(1)
Y1
(13)
Y2
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984 and IEC
Publication 617-12.
1
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
2
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8.0mA
I
OL
= 100μA
I
OH
= -8.0mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.9
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
V
V
OH
V
I
OS
mA
mA
I
OL
3
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SS
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
4
AC ELECTRICAL CHARACTERISTICS
2
(V
DD
= 5.0V
±10%;
V
SS
= 0V
1
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
Error: Description Resource Path Location TypeThis project was created using a version of compiler that is not currently installed - 5.2.7 [ARM].It shows that the ti-cgt-arm_5.2.7 package cannot be fo...
I am using 28377d to do a project. One of its functions is to collect data and display it on TFT-LCD. I am planning to use SSD1963 as the control chip of LCD. Can I directly use 28377's EMIF interface...
After unpacking the kw41z component, I wanted to use the small chip inside to draw the PCB, but I couldn't find any relevant information. Does anyone know where to find it? I hope to let you know [url...
[align=left][font=微软雅黑]1. Overview of MOS tube drive circuits [/font][/align][align=left][font=微软雅黑]When using MOS tubes to design switching power supplies or motor drive circuits, most people will co...
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
0 Introduction
Portable terminals integrate a computer and display screen into a single device. Due to limited space in portable devices, previous designs often used a single-chip microcompute...[Details]
Generally not, but there are exceptions. For example, a torque motor controller with three-phase output voltage imbalance can cause current imbalance, similar to a phase loss. However, only two pha...[Details]
ESD protection diodes are specialized for small-signal ESD protection or surge protection TVS arrays, often used for multi-circuit protection. Their small package size, low on-state voltage, high i...[Details]
Deep in the laboratory, a seemingly ordinary piece
of
battery
material
was fed into the China Advanced Research Reactor (CARR). Scientists activated the neutron depth profiling device,...[Details]
As in-vehicle audio and video entertainment features become increasingly diverse, the demand for digital transmission of audio and video information is urgent. Traditional protocols such as IEEE 13...[Details]
1. Introduction to power amplifier circuit
1. Generally speaking, the main function of a power amplifier circuit is to allow the load to obtain maximum power without distorting the signal or c...[Details]
What is the difference in response time when the output uses cyclic refresh and direct refresh?
The time required from when the PLC receives an input signal to when the PLC outputs a con...[Details]
Robots are rapidly being deployed in diverse scenarios. Flexible, easy-to-use, and fast-to-deploy robots can be quickly adapted to diverse application scenarios across various industries, making th...[Details]
On August 9th, at the 2025 World Robotics Conference (WRC), Shenzhen Cyborg Robotics Co., Ltd. officially unveiled the Cyborg-H01, the world's first lightweight bionic dexterous hand. This core com...[Details]
Introduction
With the development of mobile internet, technological advancements, and the introduction of high-performance, low-power processing chips, the variety of smart wearable devices has...[Details]
On August 8th, at the 2025 World Conference held in Beijing, Orbbec, under the theme of "Inspired and Dynamic," unveiled a new lineup of sensing products for the robotics field. Among them were the...[Details]
This article uses a heavy-duty off-road vehicle as an example to design a gateway and body control software based on a domain controller (DC). The article also examines the feasibility of u...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
