Intelligent Power Module
and Gate Drive Interface
Optocouplers
Technical Data
HCPL-4506
HCPL-J456
HCPL-0466
HCNW4506
Features
• Performance Specified for
Common IPM Applications
over Industrial Temperature
Range: -40
°
C to 100
°
C
• Fast Maximum Propagation
Delays
t
PHL
= 480 ns
t
PLH
= 550 ns
• Minimized Pulse Width
Distortion
PWD = 450 ns
• 15 kV/
µ
s Minimum Common
Mode Transient Immunity
at V
CM
= 1500 V
• CTR > 44% at I
F
= 10 mA
• Safety Approval
UL Recognized
-3750 V rms / 1 min. for
HCPL-4506/0466/J456
-5000 V rms / 1 min. for
HCPL-4506 Option 020
and HCNW4506
CSA Approved
IEC/EN/DIN EN 60747-5-2
Approved
-V
IORM
= 560 Vpeak for
HCPL-0466 Option 060
-V
IORM
= 630 Vpeak for
HCPL-4506 Option 060
-V
IORM
= 891 Vpeak for
HCPL-J456
-V
IORM
= 1414 Vpeak for
HCNW4506
Applications
• IPM Isolation
• Isolated IGBT/MOSFET Gate
Drive
• AC and Brushless DC Motor
Drives
• Industrial Inverters
Functional Diagram
Truth Table
LED
V
O
L
H
ON
OFF
NC
1
20 kΩ
8
V
CC
ANODE
2
7
V
L
CATHODE
3
6
V
O
NC
4
SHIELD
5
GND
The connection of a 0.1
µF
bypass capacitor between pins 5 and 8 is recommended.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
2
Description
The HCPL-4506 and HCPL-0466
contain a GaAsP LED while the
HCPL-J456 and the HCNW4506
contain an AlGaAs LED. The LED
is optically coupled to an inte-
grated high gain photo detector.
Minimized propagation delay
difference between devices makes
these optocouplers excellent
solutions for improving inverter
efficiency through reduced
switching dead time.
An on chip 20 kΩ output pull-up
resistor can be enabled by
shorting output pins 6 and 7, thus
eliminating the need for an
external pull-up resistor in
common IPM applications.
Specifications and performance
plots are given for typical IPM
applications.
Selection Guide
Standard
8-Pin DIP
(300 Mil)
HCPL-4506
White Mold
8-Pin DIP
(300 Mil)
HCPL-J456
Package
Type
Part
Number
Small Outline
SO8
HCPL-0466
Widebody
(400 Mil)
HCNW4506
Hermetic*
HCPL-5300
HCPL-5301
—
IEC/EN/DIN V
IORM
= 630 Vpeak V
IORM
= 891 Vpeak V
IORM
= 560 Vpeak V
IORM
= 1414 Vpeak
EN 60747-
(Option 060)
(Option 060)
5-2
Approval
*Technical data for these products are on separate Agilent publications.
Ordering Information
Specify Part Number followed by Option Number (if desired).
Example:
HCPL-4506#XXXX
020 = UL 5000 V rms/1 minute Option** for HCPL-4506 Only.
060 = IEC/EN/DIN EN 60747-5-2 Option** for HCPL-4506/0466.
300 = Gull Wing Lead Option for HCPL-4506/J456, HCNW4506.
500 = Tape and Reel Packaging Option
XXXE = Lead Free Option
Option data sheets are available. Contact Agilent sales representative or authorized distributor
for information.
**Combination of Option 020 and Option 060 is not available.
Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July
2001 and lead free option will use “-”
3
Package Outline Drawings
HCPL-4506 Outline Drawing
9.65 ± 0.25
(0.380 ± 0.010)
TYPE NUMBER
8
7
6
5
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
OPTION CODE*
DATE CODE
A XXXXZ
YYWW RU
1
1.19 (0.047) MAX.
2
3
4
UL
RECOGNITION
1.78 (0.070) MAX.
+ 0.076
0.254 - 0.051
+ 0.003)
(0.010 - 0.002)
5° TYP.
3.56 ± 0.13
(0.140 ± 0.005)
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
1.080 ± 0.320
(0.043 ± 0.013)
0.65 (0.025) MAX.
2.54 ± 0.25
(0.100 ± 0.010)
DIMENSIONS IN MILLIMETERS AND (INCHES).
* MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
HCPL-4506 Gull Wing Surface Mount Option 300 Outline Drawing
LAND PATTERN RECOMMENDATION
9.65 ± 0.25
(0.380 ± 0.010)
8
7
6
5
1.016 (0.040)
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
1
2
3
4
1.27 (0.050)
2.0 (0.080)
1.19
(0.047)
MAX.
1.780
(0.070)
MAX.
9.65 ± 0.25
(0.380 ± 0.010)
7.62 ± 0.25
(0.300 ± 0.010)
+ 0.076
0.254 - 0.051
+ 0.003)
(0.010 - 0.002)
3.56 ± 0.13
(0.140 ± 0.005)
1.080 ± 0.320
(0.043 ± 0.013)
0.635 ± 0.130
2.54
(0.025 ± 0.005)
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
0.635 ± 0.25
(0.025 ± 0.010)
12° NOM.
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
4
Package Outline Drawings
HCPL-J456 Outline Drawing
9.80 ± 0.25
(0.386 ± 0.010)
TYPE NUMBER
8
7
6
5
7.62 ± 0.25
(0.300 ± 0.010)
6.35 ± 0.25
(0.250 ± 0.010)
OPTION CODE*
DATE CODE
A XXXXZ
YYWW RU
1
1.19 (0.047) MAX.
2
3
4
UL
RECOGNITION
1.78 (0.070) MAX.
+ 0.076
0.254 - 0.051
+ 0.003)
(0.010 - 0.002)
5° TYP.
3.56 ± 0.13
(0.140 ± 0.005)
4.70 (0.185) MAX.
0.51 (0.020) MIN.
2.92 (0.115) MIN.
1.080 ± 0.320
(0.043 ± 0.013)
0.65 (0.025) MAX.
2.54 ± 0.25
(0.100 ± 0.010)
DIMENSIONS IN MILLIMETERS AND (INCHES).
* MARKING CODE LETTER FOR OPTION NUMBERS
"L" = OPTION 020
"V" = OPTION 060
OPTION NUMBERS 300 AND 500 NOT MARKED.
NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX.
HCPL-J456 Gull Wing Surface Mount Option 300 Outline Drawing
LAND PATTERN RECOMMENDATION
9.80 ± 0.25
(0.386 ± 0.010)
8
7
6
5
1.016 (0.040)
6.350 ± 0.25
(0.250 ± 0.010)
10.9 (0.430)
1
2
3
4
1.27 (0.050)
2.0 (0.080)
1.19
(0.047)
MAX.
1.780
(0.070)
MAX.
9.65 ± 0.25
(0.380 ± 0.010)
7.62 ± 0.25
(0.300 ± 0.010)
+ 0.076
0.254 - 0.051
+ 0.003)
(0.010 - 0.002)
3.56 ± 0.13
(0.140 ± 0.005)
1.080 ± 0.320
(0.043 ± 0.013)
0.635 ± 0.130
2.54
(0.025 ± 0.005)
(0.100)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).
0.635 ± 0.25
(0.025 ± 0.010)
12° NOM.
NOTE: FLOATING LEAD PROTRUSION IS 0.5 mm (20 mils) MAX.
5
HCPL-0466 Outline Drawing (8-Pin Small Outline Package)
LAND PATTERN RECOMMENDATION
8
7
6
5
3.937 ± 0.127
(0.155 ± 0.005)
XXX
YWW
5.994 ± 0.203
(0.236 ± 0.008)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
4
7.49 (0.295)
PIN ONE
1
0.406 ± 0.076
(0.016 ± 0.003)
2
3
1.9 (0.075)
1.270 BSC
(0.050)
0.64 (0.025)
*
5.080 ± 0.127
(0.200 ± 0.005)
7°
45° X
0.432
(0.017)
3.175 ± 0.127
(0.125 ± 0.005)
0 ~ 7°
1.524
(0.060)
0.203 ± 0.102
(0.008 ± 0.004)
0.228 ± 0.025
(0.009 ± 0.001)
*
TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
0.305 MIN.
(0.012)
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
HCNW4506 Outline Drawing (8-Pin Widebody Package)
11.15 ± 0.15
(0.442 ± 0.006)
8
7
6
5
11.00 MAX.
(0.433)
9.00 ± 0.15
(0.354 ± 0.006)
TYPE NUMBER
DATE CODE
A
HCNWXXXX
YYWW
1
2
3
4
1.55
(0.061)
MAX.
10.16 (0.400)
TYP.
7° TYP.
+ 0.076
0.254 - 0.0051
+ 0.003)
(0.010 - 0.002)
5.10 MAX.
(0.201)
3.10 (0.122)
3.90 (0.154)
2.54 (0.100)
TYP.
1.78 ± 0.15
(0.070 ± 0.006)
0.40 (0.016)
0.56 (0.022)
0.51 (0.021) MIN.
DIMENSIONS IN MILLIMETERS (INCHES).
NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.
京公网安备 11010802033920号
EEWORLD
