EEWORLDEEWORLDEEWORLD

Part Number

Search

MC-212RC

Description
Coil Components (Relay Headers)
CategoryWireless rf/communication    Radio frequency and microwave   
File Size121KB,4 Pages
ManufacturerHirose
Websitehttp://www.hirose-connectors.com/
Download Datasheet Parametric View All

MC-212RC Overview

Coil Components (Relay Headers)

MC-212RC Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codeunknow
Other featuresHIGH RELIABILITY
Characteristic impedance75 Ω
structureCOMPONENT
Maximum input power (CW)26.99 dBm
Maximum insertion loss0.6 dB
Maximum operating frequency95 MHz
Minimum operating frequency50 MHz
Maximum operating temperature65 °C
Minimum operating temperature-10 °C
RF/Microwave Device TypesSPLITTER AND COMBINER
Maximum voltage standing wave ratio1.2
Base Number Matches1
Coil Components (Relay Headers)
MC-R and MC-RC Series
75 ohms Type (MC-RC Series)
s
Features
1.Excellent High Frequency Characteristics
The use of coils made with a special winding
method based on a lumped-constant design
provide a high degree of matching, low loss, and
high isolation.
MC-201RC
MC-202RC
MC-301RC
MC-212RC
MC-211RC
MC-213RC
2.Highly Reliable Design
The metal case is designed with a hermetically sealed
construction which contains inert gas. This permits
quality to be maintained over a long period.
MC-216RC
MC-214RC
50 ohms Type (MC-R Series)
3.Easy Soldering
The pre-soldering leads give easy soldering operations.
4.Prevention of Flux Creepage
MC-201R
MC-212R
MC-213R
Use of the supplied Teflon sheet permits the prevention
of solder flux creepage.
s
Product Specifications
Ratings
Frequency range (Note)
Characteristic impedance (Note)
Maximum Input Power
30 to 200 MHz
50 ohms, 75 ohms
0.5 W
Operating temperature range
Operating relative humidity
-10
ç
to +65
ç
95% Max.
Note: The frequency range and the characteristic impedance will differ depending on the products.
Item
1.Vibration
2.Shock
3.Temperature cycle
Standard
Conditions
Frequency of 10 to 2000 Hz, overall amplitude of 1.5 mm,
acceleration of 98 m/s
2
for 4 hours in each of 3 directions
No damage, cracks, or parts dislocation
Acceleration of 294 m/s
2
, sine half-wave waveform, 3 cycles in each of the 3 axis
Temperature: -35
ç
¡
+5
ç
to +35
ç
¡
+85
ç
¡
+5
ç
to +35
ç
Time: 30
¡
15 max.
¡
30
¡
15 max. (Minutes)
5 cycles
q
The test method conforms to MIL-STD-202.
s
Materials
Part
Board
Contacts
Hermetic seal
s
External Dimensions
Material
Iron
Iron-nickel alloy
Glass
Finish
Nickel plating
Solder dip
----------
Teflon sheet (t=0.2)
s
Ordering Information
MC - 2 0 1 R C
1
2 3 4 5
6
Green hermetic seal
s
Function Diagram
1
Series Name: MC
2
Number of Divisions
Indicated by number of divisions of output.
4
Suffix
5
Form of Case
R: Relay header
2, 3, 4, 5, and 6 are ground
3, 4, 7, and 8 are ground
3
Phase Difference
6
Characteristic Impedance
Indicated by phase difference of output.
C : 75
ø
0 : 0
°
Blank : 50
ø
1 : 90
°
3, 4, 7, and 8 are ground
3, 4, and 7 are ground
49
Questions about msp430
I'm learning msp430f5438 recently. After installing IAR, I found that there is no header file for 5438 in the header file. For example, registers such as TACTL and TAR cannot be recognized. Is it beca...
tm890912 Microcontroller MCU
CP2201 Issues
Hello everyone, I used 8051 and CP2201 to make an Ethernet interface. During the initialization of the CP2201 physical layer, the value of INT1RD is always 0X31 regardless of whether it is connected o...
cqwjfb MCU
Automatic Wire Winding Tool Specctra Guide
Very good @ Share it with everyone...
dykonka PCB Design
Some thoughts on interference in industrial environments
In many cases, we have to talk about anti-interference. Where does the interference come from? I personally think that 30% of the devices that are interfered with are caused by power supply interferen...
aone2008 Industrial Control Electronics
Excuse me, can rom be set in cpld?
Excuse me, can rom be set in cpld?I have seen FPGAs, but I don't know how CPLDs are....
qchpanna FPGA/CPLD
How to generate lib files under TC
Hello experts, I want to write a LIB file in TC, but I don't know how to start. What is the format of the LIB file? I hope you can give me some advice. It would be best if you have examples. Thank you...
nlinger Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2116  2872  482  2302  979  43  58  10  47  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号