The UT54ACS04 and the UT54ACTS04 are hex inverters. The
circuits perform the Boolean function Y = A.
The devices are characterized over full military temperature
range of -55°C to +125°C.
FUNCTION TABLE
INPUT
A
H
L
OUTPUT
Y
L
H
PINOUTS
14-Pin DIP
Top View
A1
Y1
A2
Y2
A3
Y3
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
A6
Y6
A5
Y5
A4
Y4
14-Lead Flatpack
Top View
A1
Y1
A2
Y2
A3
Y3
V
SS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
V
DD
A6
Y6
A5
Y5
A4
Y4
LOGIC DIAGRAM
A1
(2)
(4)
(6)
(8)
(10)
(12)
Y1
Y2
Y3
Y4
Y5
Y6
and
A4
Y4
A3
Y3
Y1
LOGIC SYMBOL
A1
A2
A3
A4
A5
A6
(1)
(3)
(5)
(9)
(11)
(13)
1
A2
Y2
Note:
1. Logic symbol in accordance with ANSI/IEEE standard 91-1984
IEC Publication 617-12.
A5
Y5
A6
Y6
1
OPERATIONAL ENVIRONMENT
1
PARAMETER
Total Dose
SEU Threshold
2
SEL Threshold
Neutron Fluence
LIMIT
1.0E6
80
120
1.0E14
UNITS
rads(Si)
MeV-cm
2
/mg
MeV-cm
2
/mg
n/cm
2
Notes:
1. Logic will not latchup during radiation exposure within the limits defined in the table.
2. Device storage elements are immune to SEU affects.
ABSOLUTE MAXIMUM RATINGS
SYMBOL
V
DD
V
I/O
T
STG
T
J
T
LS
Θ
JC
I
I
P
D
PARAMETER
Supply voltage
Voltage any pin
Storage Temperature range
Maximum junction temperature
Lead temperature (soldering 5 seconds)
Thermal resistance junction to case
DC input current
Maximum power dissipation
LIMIT
-0.3 to 7.0
-.3 to V
DD
+.3
-65 to +150
+175
+300
20
±10
1
UNITS
V
V
°C
°C
°C
°C/W
mA
W
Note:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at
these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended
periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
V
IN
T
C
PARAMETER
Supply voltage
Input voltage any pin
Temperature range
LIMIT
4.5 to 5.5
0 to V
DD
-55 to + 125
UNITS
V
V
°C
2
DC ELECTRICAL CHARACTERISTICS
7
(V
DD
= 5.0V
±
10%; V
SS
= 0V
6
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
SYMBOL
V
IL
PARAMETER
Low-level input voltage
1
ACTS
ACS
High-level input voltage
1
ACTS
ACS
Input leakage current
ACTS/ACS
Low-level output voltage
3
ACTS
ACS
High-level output voltage
3
ACTS
ACS
Short-circuit output current
2 ,4
ACTS/ACS
Output current
10
(Sink)
I
OH
Output current
10
(Source)
P
total
I
DDQ
ΔI
DDQ
Power dissipation
2, 8, 9
Quiescent Supply Current
Quiescent Supply Current Delta
ACTS
V
IN
= V
DD
or V
SS
I
OL
= 8mA
I
OL
= 100μA
I
OH
= -8mA
I
OH
= -100μA
V
O
= V
DD
and V
SS
V
IN
= V
DD
or V
SS
V
OL
= 0.4V
V
IN
= V
DD
or V
SS
V
OH
= V
DD
- 0.4V
C
L
= 50pF
V
DD
= 5.5V
For input under test
V
IN
= V
DD
- 2.1V
For all other inputs
V
IN
= V
DD
or V
SS
V
DD
= 5.5V
C
IN
C
OUT
Input capacitance
5
Output capacitance
5
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
15
15
pF
pF
1.8
10
1.6
mW/
MHz
μA
mA
-8
mA
.7V
DD
V
DD
- 0.25
-200
8
200
.5V
DD
.7V
DD
-1
1
0.40
0.25
CONDITION
MIN
MAX
0.8
.3V
DD
UNIT
V
V
IH
V
I
IN
V
OL
μA
V
V
OH
V
I
OS
I
OL
mA
mA
3
Notes:
1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V
IH
= V
IH
(min) + 20%, - 0%; V
IL
= V
IL
(max) + 0%, -
50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are
guaranteed to V
IH
(min) and V
IL
(max).
2. Supplied as a design limit but not guaranteed or tested.
3. Per MIL-PRF-38535, for current density
≤
5.0E5 amps/cm
2
, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765
pF/MHz.
4. Not more than one output may be shorted at a time for maximum duration of one second.
5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and V
SSs
at
frequency of 1MHz and a signal amplitude of 50mV rms maximum.
6. Maximum allowable relative shift equals 50mV.
7. All specifications valid for radiation dose
≤
1E6 rads(Si).
8. Power does not include power contribution of any TTL output sink current.
9. Power dissipation specified per switching output.
10. This value is guaranteed based on characterization data, but not tested.
4
AC ELECTRICAL CHARACTERISTICS
2
(V
DD
= 5.0V
±
10%; V
SS
= 0V
1
, -55°C < T
C
< +125°C); Unless otherwise noted, Tc is per the temperature range ordered.
I am a beginner in switching power supply. When making a forward DC-DC converter, I found that the voltage will be pulled down when the load is heavy. I suspect it is a problem with the winding of the...
[i=s]This post was last edited by 1nnocent on 2021-4-29 15:40[/i]The winners of the book "Operational Amplifier Parameter Analysis and LTspice Application Simulation" are out.
I am very happy to read ...
With the advancement of computer technology, the development of image processing and pattern recognition methods, fingerprint processing technology has become more mature and has been widely used i...[Details]
In the test of the electronic ignition module, in order to simulate the real working condition of the electronic ignition system, the electronic ignition module is often placed in an environment hi...[Details]
Infrared remote control is widely used in household appliances, security, industrial control and people's daily life, especially household appliances and security.
When there are many TVs, VCD...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
With the development of supermarket industry and the strengthening of loss prevention awareness, the use of electronic anti-theft equipment (EAS) has become very popular in various parts of the countr...[Details]
The overcurrent and overheating coordinated protection technology implemented by polymer positive temperature coefficient devices (PPTC) can protect motors, controllers and electronic components in...[Details]
introduction
The data detected by various measuring instruments often need to be transferred to the PC for data processing and archiving, so as to make full use of the rich hardware and softwa...[Details]
introduction
With the rapid development of my country's aviation industry, various new aircraft and control equipment have been successfully developed. Some previous measurement and control eq...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
1 Basic structure and function of implantable cardioverter defibrillator (ICD)
ICD consists of two parts: the pulse generator and the electrode lead. The main components of the pulse generator...[Details]
Electrocardiogram is an important means of diagnosing heart disease. However, due to various reasons, it is difficult to capture abnormal electrocardiograms with ordinary electrocardiographs. Although...[Details]
introduction
With the increasing popularity of Internet applications, the degree of information sharing is constantly improving. The digitization and networking of embedded devices has b...[Details]
LED dot matrix blocks have the advantages of high brightness, uniform light emission, good reliability, and easy assembly, and can form display screens of various sizes. At present, LED display scr...[Details]
Pulse compression technology refers to the process of modulating the wide pulse signal emitted by the radar (such as linear frequency modulation, nonlinear frequency modulation, phase coding), and ...[Details]
Abstract:
A single pulse secondary radar reply processor implemented with EPLD. Its main functions include: reply frame pulse detection, reply information decoding, assembling reply inf...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
