Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= full range, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C and V
CC
= 3V.) (Note 1)
PARAMETER
V
CC
Range
SYMBOL
CONDITIONS
T
A
= 0°C to +70°C
T
A
= -40°C to +85°C
I
CC
MAX632_ only, V
CC
= 3.0V for V
TH
≤
2.93V,
V
CC
= 3.2V for V
TH
> 2.93V, no load
V
CC
= 5.5V, no load
T
A
= +25°C
Reset Threshold
V
TH
Table 1
T
A
= -40°C to +85°C
Reset Threshold Tempco
V
CC
to Reset Delay
Reset Active Timeout Period
RESET
Output Voltage
(MAX6326/MAX6328/
MAX6346/MAX6348)
RESET
Output Voltage
(MAX6326/MAX6346)
I
SINK
= 1.6mA, V
CC
> 2.1V, reset asserted
V
OL
I
SINK
= 100µA, V
CC
≥
1.2V, reset asserted
I
SOURCE
= 500µA, V
CC
= 3.2V, MAX6326 only
V
OH
I
SOURCE
= 800µA, V
CC
= 4.5V, V
TH
≤
4.38V
I
SOURCE
= 800µA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
V
OH
RESET Output Voltage
(MAX6327/MAX6347)
V
OL
I
SOURCE
= 500µA, V
CC
≥
2.1V, reset asserted
I
SOURCE
= 50µA, V
CC
≥
1.2V, reset asserted
I
SINK
= 1.2mA, V
CC
≥
3.2V, reset not asserted,
MAX6327 only
I
SINK
= 3.2mA, V
CC
≥
4.5V, reset not asserted,
V
TH
≤
4.38V
I
SINK
= 3.2mA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
RESET Threshold
Hysteresis
Open-Drain
RESET
Output
Leakage Current
Note 1:
Overtemperature limits are guaranteed by design and not production tested.
What kind of embedded PPP is it? Is it similar to PPP over Ethernet? If I want to develop TCP protocol frames myself, how do I send data using the IP address assigned after dialing successfully? What ...
I would like to ask, has anyone used 51 single chip microcomputer to control VGA display to display text and pictures, graduation project. Who can provide information? Thank you very much...
It specifies the form, basic dimensions, technical requirements, etc. of three-phase synchronous generators driven by compound internal combustion engines...
Event: The company simultaneously released its 2017 annual report and the first quarter report of 2018. In 2017, the company achieved revenue of 8.886 billion yuan, a year-on-year increase of 48.01...[Details]
Recently, the US embargo on ZTE has attracted much attention. Let's take a look at the relevant content with the automotive electronics editor. On April 16, local time, the U.S. Department of Co...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
When designing a product, if the application environment's requirements for power isolation are not considered, the product will be unstable due to improper design, and even high voltage may damage t...[Details]
I slightly changed the lyrics of Yu Quan's song "Running", which seems to be
a reflection of the current state of
Huawei Cloud
. At the annual Huawei Analyst Conference held on April 17,
Zh...[Details]
On Sunday, the South Australian government unveiled plans to build the world's largest virtual power plant, which will connect at least 50,000 homes over four years and have a capacity ...[Details]
In order to strengthen the traceability management of recycling and utilization of power batteries for new energy vehicles, and to standardize and guide all relevant parties to fulfill their tracea...[Details]
1. Function and purpose There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
12864 LCD parallel port driver is more commonly used, but considering that sometimes the IO port of the microcontroller or MCU is limited, the serial driver method can be used. The following is ...[Details]
Since 2018, the field of artificial intelligence chips has been very lively. Especially in China, the rich vertical application scenarios have provided fertile ground for the development of AI chip...[Details]
Unfortunately, my serial port has some problems and I can't print information. I can only debug to view variables and see the values. Fortunately, there is not much AD conversion code, and I can use ...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
