3. Epoxy meniscus may extend about 1mm (0.040”) down the leads.
Device Selection Guide
Iv (cd) @ 20mA
Part Number
HLMP-CW18-VY0xx
HLMP-CW19-VY0xx
HLMP-CW28-TW0xx
HLMP-CW29-TW0xx
HLMP-CW38-SV0xx
HLMP-CW39-SV0xx
Notes:
1. Tolerance for luminous intensity measurement is +/- 15%
2. The luminous intensity is measured on the mechanical axis of the lamp package.
3. The optical axis is closely aligned with the package mechanical axis.
4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper safety
equipment.
Typ. Viewing Angle
Min.
15°
15°
23°
23°
30°
30°
4.20
4.20
2.50
2.50
1.90
1.90
Typ.
6.40
6.40
3.80
3.80
3.00
3.00
Standoff Leads
No
Yes
No
Yes
No
Yes
Package
Dimension
A
B
A
B
A
B
Part Numbering System
L M P - C W XX - X X X XX
Mechanical Option
00: Bulk
DD: Ammo Pack
Color Bin Options
0: Full color bin distribution
Maximum Intensity Bin Limit
0: No maximum intensity bin limit
Minimum Intensity Bin Limit
Refer to Device Selection Guide
Viewing Angle
18: 15 without standoffs
19: 15˚ with standoffs
28: 23˚ without standoffs
29: 23˚ with standoffs
38: 30 ˚ without standoffs
39: 30 ˚ with standoffs
Color Options
W: White
Package Options
C: T-1 3/4
2
Absolute Maximum Ratings (T
A
= 25°C)
Parameter
DC Forward Current
[1]
Peak Forward Current
[2]
Average Forward Current
Power Dissipation
LED Junction Temperature
Operating Temperature Range
Storage Temperature Range
Wave Solder Temperature
[3]
Solder Dipping Temperature
[3]
Notes:
1. Derate linearly as shown in Figure 4.
2. Duty Factor 30%, 1 KHz
3. 1.59 mm (0.060 inch) below body
Value
30
100
30
120
130
-40 to +85
-40 to +100
250 for 3 secs
260 for 5secs
Units
mA
mA
mA
mW
°C
°C
°C
°C
°C
Electrical/Optical Characteristics (T
A
= 25
o
C)
Parameters
Forward voltage
Capacitance
Reverse Voltage
[1]
Thermal resistance
Viewing Angle
[2]
CW18/CW19
CW28/CW29
CW38/CW39
Symbol
V
F
C
V
R
Rθ
J-PIN
2θ
1/2
15
23
30
0.31
0.32
I
F
= 20 mA
Minimum Typical
3.4
53
0.6
240
Maximum Units
4.0
V
pF
V
o
C/W
Test Condition
I
F
= 20 mA
V
F
=0, f=1 MHz
I
R
= 10
µA
LED Junction to cathode lead
I
F
= 20 mA
Degree
Chromaticity Coordinate
[3]
X
Y
Notes:
2. 2
θ
1/2
is the off-axis angle where the luminous intensity is ½ the on axis intensity
1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at I
R
= 10
µ
A
3. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device.
[i=s]This post was last edited by y909334873 on 2016-9-5 11:03[/i] I just started learning about file systems and transplanted a fat file system to a microcontroller. This problem occurred. I created ...
[color=#222222][backcolor=rgb(238, 238, 238)][font=sans-serif]As shown in the picture above, putting more vias on the ground pad of the voltage regulator can help dissipate heat. I know this. I just w...
1) Install the Cube Suite+ environment. 2) Install the emulator driver. This is very simple. Just plug in the USB and it will work. The driver is in the CD. 3) Flash the specified firmware for the emu...
[b]Abstract[/b]The vehicle-mounted GPS navigation system is an emerging technology product that integrates GPS technology, CIS technology, communication technology and computer network technology. GPS...
This is a 16*32 program in the forum. The row selector is 154, and the column selector is 595. I don't quite understand how to look up the table and send the data to the dot matrix screen. I hope some...
I have been doing R&D for almost 5 years, and I have worked on MCU, DSP, and ARM, which is quite diverse. The current mainstream positions in the electronic information industry include ARM+OS develop...
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
In public places such as schools, government agencies, factories and mines, as well as public corridors in residential areas, the phenomenon of long-burning lights is very common, which causes a h...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1. Overview
The Virtual CAN Interface (VCI) function library is an application program interface specifically provided for the use of ZLGCAN devices on PCs. The functions in the library ar...[Details]
1. Project Introduction
Shandong Dezhou Xingtai Paper Co., Ltd. is a newly built high-end paperboard production enterprise with domestic leading level established by Shandong Zhaodongfang Pape...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
Nippon Electric Works and Volvo Technology Japan have developed a wireless power supply system for electric vehicles (EVs). Using this system, the two companies have successfully conducted an exper...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
Since the late 1990s, with the demand for higher system efficiency and lower power consumption, the technological update of telecommunications and data communication equipment has promoted the deve...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
Traditional
virtual instruments
consist of a data acquisition
board
based on PCI bus and
corresponding software. However, with
the rapid development of
computer
network techno...[Details]
0 Introduction
Wireless Sensor Network (WSN) monitors the target by deploying a large number of sensor nodes in the target area. WSN realizes the positioning and tracking of the target, determi...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
