EEWORLDEEWORLDEEWORLD

Part Number

Search

AD4C211-L-H-S-TR

Description
Solid State Relay
CategoryLED optoelectronic/LED    photoelectric   
File Size213KB,5 Pages
ManufacturerSSOUSA
Websitehttp://www.ssousa.com
Environmental Compliance
Download Datasheet Parametric Compare View All

AD4C211-L-H-S-TR Overview

Solid State Relay

AD4C211-L-H-S-TR Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerSSOUSA
Reach Compliance Codeunknown
Base Number Matches1
AD4C211-L
Dual 1 Form A
Solid State Relay
DESCRIPTION
The AD4C211-L is a bi-directional, double-pole, single-throw, normally open multipurpose solid-state relay. It is designed to replace
electromechanical relays in general purpose switching applications. The relay consists of two integrated circuits, each driving a pair of
rugged source-to-source enhancement type DMOS transistors. Each integrated circuit is optically coupled to a light emitting diode. This
device also includes current-limiting circuitry. During increased load currents or transient current spikes, this circuitry acts to bring the
current down, protecting downstream components.
FEATURES
APPLICATIONS
Current limiting (over-current protection)
Low input control power consumption (1.5mA TYP)
140mA maximum continuous load current
25 ohms maximum on-resistance
High input-to-output isolation
Long life/high reliability
Multiplexers
Meter reading systems
Data Acquisition
Medical equipment
Battery monitoring
Home/Safety security systems
OPTIONS/SUFFIXES*
ABSOLUTE MAXIMUM RATINGS*
PARAMETER
Storage Temperature
Operating Temperature
Continuous Input Current
Transient Input Current
Reverse Input Control
Voltage
Output Power Dissipation
UNIT
°C
°C
mA
mA
V
mW
6
800
MIN
-55
-40
TYP
MAX
125
85
40
400
-H
-S
-TR
High Input / Output isolation
Surface Mount Option
Tape and Reel Option
NOTE: Suffixes listed above are not included in marking on
device for part number identification.
SCHEMATIC DIAGRAM
*The values indicated are absolute stress ratings. Functional operation of the
device is not implied at these or any conditions in excess of those defined in
electrical characteristics section of this document. Exposure to Absolute
Ratings may cause permanent damage to the device and may adversely
affect reliability.
APPROVALS
UL / C-UL Approved: File # E90096, E201932
CSA Approved: Certificate #LR111581-1
© 2009 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 5
AD4C211-L
rev 1.41 (6/17/2009)

AD4C211-L-H-S-TR Related Products

AD4C211-L-H-S-TR AD4C211-L-S-TR
Description Solid State Relay Solid State Relay
Is it Rohs certified? conform to conform to
Maker SSOUSA SSOUSA
Reach Compliance Code unknown unknown
Base Number Matches 1 1
TMIGS tunnel multi-information early warning and safety management system
[size=3]TMIGS system is jointly developed by Beijing Jiaotong University, Beijing Municipal Engineering Research Institute, and Beijing Sotong Zifeng Communication Engineering Technology Co., Ltd. The...
lwslxh Industrial Control Electronics
STM8L enters Halt mode. Where does the program return after being awakened by an interrupt and exiting the interrupt?
I have a basic question. I looked through the reference manual but couldn't find the answer. When STM8L enters Halt mode and is awakened by an interrupt, where does the program return to after exiting...
jiyiche stm32/stm8
Please tell me the function of these resistors
[img]http://hi.eeworld.net/attachment/201004/20/3276840_1271745733hZ5e.jpg[/img]1. What is the role of the two 15K resistors in the second stage op amp in this figure? Do they provide bias for the sec...
dudu2000 Embedded System
Is the 430 downloader powered when in use?
Is the 430 downloader powered when in use? Why can't I download the program, but can simulate it? Why?...
MSP430ZJZ MCU
Can vias be placed on pads?
I am making an RF board, and I use 0402 for resistor and capacitor packages. I put 0.2mm vias on the pads of the 0402 package, and covered the vias with oil. Is this OK? Although there will be no tin ...
943614033 PCB Design
How do you test the chip driver code you write?
I specialize in FPGA chip driver code, but I have written the code, but the chip FPGA is not yet finished. Is there any way to verify whether the code I wrote is correct? How do you usually test it?...
shangyl Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2459  2742  2689  2519  3  50  56  55  51  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号