3. Epoxy meniscus may extend about 1mm (0.040”) down the leads.
Device Selection Guide
Iv (cd) @ 20mA
Part Number
HLMP-CW18-VY0xx
HLMP-CW19-VY0xx
HLMP-CW28-TW0xx
HLMP-CW29-TW0xx
HLMP-CW38-SV0xx
HLMP-CW39-SV0xx
Notes:
1. Tolerance for luminous intensity measurement is +/- 15%
2. The luminous intensity is measured on the mechanical axis of the lamp package.
3. The optical axis is closely aligned with the package mechanical axis.
4. LED light output is bright enough to cause injuries to the eyes. Precautions must be taken to prevent looking directly at the LED without proper safety
equipment.
Typ. Viewing Angle
Min.
15°
15°
23°
23°
30°
30°
4.20
4.20
2.50
2.50
1.90
1.90
Typ.
6.40
6.40
3.80
3.80
3.00
3.00
Standoff Leads
No
Yes
No
Yes
No
Yes
Package
Dimension
A
B
A
B
A
B
Part Numbering System
L M P - C W XX - X X X XX
Mechanical Option
00: Bulk
DD: Ammo Pack
Color Bin Options
0: Full color bin distribution
Maximum Intensity Bin Limit
0: No maximum intensity bin limit
Minimum Intensity Bin Limit
Refer to Device Selection Guide
Viewing Angle
18: 15 without standoffs
19: 15˚ with standoffs
28: 23˚ without standoffs
29: 23˚ with standoffs
38: 30 ˚ without standoffs
39: 30 ˚ with standoffs
Color Options
W: White
Package Options
C: T-1 3/4
2
Absolute Maximum Ratings (T
A
= 25°C)
Parameter
DC Forward Current
[1]
Peak Forward Current
[2]
Average Forward Current
Power Dissipation
LED Junction Temperature
Operating Temperature Range
Storage Temperature Range
Wave Solder Temperature
[3]
Solder Dipping Temperature
[3]
Notes:
1. Derate linearly as shown in Figure 4.
2. Duty Factor 30%, 1 KHz
3. 1.59 mm (0.060 inch) below body
Value
30
100
30
120
130
-40 to +85
-40 to +100
250 for 3 secs
260 for 5secs
Units
mA
mA
mA
mW
°C
°C
°C
°C
°C
Electrical/Optical Characteristics (T
A
= 25
o
C)
Parameters
Forward voltage
Capacitance
Reverse Voltage
[1]
Thermal resistance
Viewing Angle
[2]
CW18/CW19
CW28/CW29
CW38/CW39
Symbol
V
F
C
V
R
Rθ
J-PIN
2θ
1/2
15
23
30
0.31
0.32
I
F
= 20 mA
Minimum Typical
3.4
53
0.6
240
Maximum Units
4.0
V
pF
V
o
C/W
Test Condition
I
F
= 20 mA
V
F
=0, f=1 MHz
I
R
= 10
µA
LED Junction to cathode lead
I
F
= 20 mA
Degree
Chromaticity Coordinate
[3]
X
Y
Notes:
2. 2
θ
1/2
is the off-axis angle where the luminous intensity is ½ the on axis intensity
1. The reverse voltage of the product is equivalent to the forward voltage of the protective chip at I
R
= 10
µ
A
3. The chromaticity coordinates are derived from the CIE 1931 Chromaticity Diagram and represent the perceived color of the device.
I am making a simple clock recently. I use TimerA to generate a second interrupt, which can tell the time more accurately. Now I want to add a key interrupt of P1.3 to collect the internal temperature...
I recently saw some good information about dsp level conversion! I'll post it here for everyone to see. 1. Commonly used level conversion schemes (1) Transistor + pull-up resistor method is a bipolar ...
Our company uses a STM8S103F3 MCU to design a refrigerator board. Now we need to design the temperature control program inside. If you are interested, please leave your contact information. It is best...
As the title says, you need to have ASIC/FPGA design or verification experience, three years of undergraduate experience, and more than two years of master's experience. If you are interested, please ...
[size=6]Hello everyone: [/size] [size=6]I posted a message in the forum seeking help to solve the network port communication problem of 44B0, but no one has come to help me so far. [/size] [size=6]I h...
Radio Frequency Identification (RFID) technology is a non-contact automatic identification technology that uses wireless radio frequency communication. Compared with the currently widely used barco...[Details]
As the application scope of medical equipment expands from hospitals to emergency response and home medical environments, its mobility will be determined by many factors. In addition, medical equip...[Details]
Signal sources have developed to a very wide range today. We can classify them according to the frequency range: ultra-low frequency (0.1m～1kHz), audio (20Hz～20kHz), video (20kHz～10MHz), radio fre...[Details]
introduction
Like other
portable
electronic products,
blood flow parameter detectors
need to be small, thin, durable, reliable, and have a long standby time. Therefore, system desi...[Details]
Preface
For a long time, SD cards with Flash Memory as storage have been widely used in consumer electronic products due to their small size, low power consumption, erasable and non-volati...[Details]
0Introduction
As a service robot in the field of medical care, the application of smart wheelchairs makes extensive use of mobile robot technology. The key technologies involved in the researc...[Details]
1. What is fading?
In terms of scope, fading can be roughly divided into three types: large area fading, small area fading and indoor fading. As shown in Figure 1, large area fading refers t...[Details]
According to In-Stat/MDR, the number of mobile phones with Bluetooth capabilities will reach at least 300 million by 2005. One of the clear evidences of the increasing adoption of Bluetooth is that...[Details]
IPTV (Internet Protocol TV or Interactive Personal TV), also known as interactive network television, is a new technology that uses broadband network infrastructure, takes home televisions or comp...[Details]
0 Introduction
At present, most of the automatic blood pressure monitoring systems used in hospitals are imported equipment, which are expensive and increase the cost of medical treatment. The...[Details]
Test equipment manufacturers are constantly challenged to develop new test solutions that meet the latest product testing needs of their customers, and they often design specialized hardware t...[Details]
When it comes to ATX power supply, people will think of two "classic" ICs: pulse width modulation chip TL494 and voltage comparator LM339. The new dedicated control chip AT2005B has the functions ...[Details]
0Introduction
Microactuators, as driving components of microelectromechanical systems (MEMS), have been widely studied. In recent years, actuators made of hard magnetic and soft magnetic m...[Details]
0 Introduction
In modern industrial production and scientific and technological research, various data usually need to be collected. The commonly used data acquisition board collection met...[Details]
The growing global interest in green power has added new variables to the design of power supplies and power adapters. Designers must not only traditionally consider the design specifications requi...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
