stability means it is the perfect choice for today’s
communications applications that require tight
frequency control.
ORDERING INFORMATION
357
SUPPLY VOLTAGE
L = +3.3 Vdc,
Pin 2 Enable (standard)
S = +5.0 Vdc,
Pin 2 Enable (standard)
V = +3.3 Vdc,
Pin 5 Enable
W = +5.0 Vdc,
Pin 5 Enable
ABSOLUTE PULL RANGE (APR)
B = ± 50 ppm APR (standard)
C = ± 80 ppm APR
D = ± 100 ppm APR
M
FREQUENCY IN MHz
M - indicates MHz and decimal point.
Frequency is recorded with minimum 4
significant digits to the right of the "M".
OPERATING TEMPERATURE RANGE
C = -20°C to +70°C (standard)
I = -40°C to +85°C
FREQUENCY STABILITY
3 = ± 50 ppm (standard)
5 = ± 25 ppm
6 = ± 20 ppm
Example Part Number: 357LB3C019M4400
Document No. 008-0244-0
Page 1 - 4
Rev. G
٠ ٠ ٠
CTS Communications Components, Inc.
٠
171 Covington Drive
٠
Bloomingdale, IL 60108
٠ ٠ ٠
٠ ٠ ٠
Phone 630-924-3500
٠
www.ctscorp.com
٠
Toll Free 800-757-6686
٠ ٠ ٠
7x5mm Low Cost
CMOS/TTL Compatible VCXO
Model 357
ELECTRICAL CHARACTERISTICS
PARAMETER
Maximum Supply Voltage
Maximum Control Voltage
Storage Temperature
Frequency Range
Frequency Stability
(See Note 1 and Ordering Information)
Absolute Maximums
SYMBOL
V
CC
V
C
T
STG
f
O
∆f/f
O
APR
T
A
± 10 %
V
CC
CONDITIONS
-
-
-
-
-
-
-
MIN
-0.5
-0.5
-55
1.5
-
50, 80 or
100
-20
-40
4.5
2.97
TYP
-
-
-
-
-
-
MAX
7.0
V
CC
125
80
20, 25 or
50
-
70
85
5.5
3.63
20
30
40
45
30
4.5
3.0
-
10
15
55
-
10%V
CC
-14
14
5.0
-
-
10
-
1
-
0.5
100
UNIT
V
V
°C
MHz
± ppm
± ppm
°C
Absolute Pull Range
(See Note 2 and Ordering Information)
Operating Temperature
Commercial
Industrial
Supply Voltage
Model 357S, 357W
Model 357L, 357V
Supply Current
25
5.0
3.3
5
8
10
12
-
2.5
3.3
135
5
8
-
-
-
-
-
3.5
-
Positive
-
-
-
-
-
-
V
I
CC
C
L
= 15 pF
1.5 MHz to 20 MHz
20.1 MHz to 40 MHz
40.1 MHz to 60 MHz
60.1 MHz to 80 MHz
Output Load
Control Voltage
Model 357S, 357W
Model 357L, 357V
Frequency Deviation
Linearity
Best Straight Line Fit
Output Duty Cycle
Output Voltage Levels
Logic '1' Level
Logic '0' Level
Output Current Levels
Logic '1' Level
Logic '0' Level
Rise and Fall Time
Input Impedance
Transfer Function
Start Up Time
Modulation Roll-off
Phase Jitter
Enable Function
Enable Input Voltage
Disable Input Voltage
Enable Time
C
L
V
C
∆f
L
SYM
V
OH
V
OL
I
OH
I
OL
T
R
, T
F
Z
C
-
T
S
-
tjms
V
IH
V
IL
T
PLZ
V
CC
= 5.0V
V
CC
= 3.3V
25°C at Time of Shipment, over V
C
range
< 52 MHz
> 52 MHz
@ 50% Level
CMOS Load
CMOS Load
CMOS Load
CMOS Load
@ 10% - 90% Levels
-
-
Application of V
CC
@ -3dB
Bandwidth 12 kHz - 20 MHz
Pin 2 or Pin 5 Logic '1', Output Enabled
Pin 2 or Pin 5 Logic '0', Output Disabled
Pin 2 or Pin 5 Logic '1'
-
-
-
-
-
0.5
0.3
-
-
45
90%V
CC
-
-
-
-
50
-
-
10
-
2.5
-
-
mA
pF
V
± ppm
%
%
V
mA
Electrical and Waveform Parameters
ns
kOhms
-
ms
kHz
ps RMS
V
ns
Notes:
1. Inclusive of initial tolerance at time of shipment, changes in supply voltage, load, temperature and 20 year aging at an average operating temperature
of +40 °C.
2. Minimum guaranteed frequency shift from f
O
over variations in temperature, aging, power supply and load at an average operating temperature
of +40°C for 10 years.
SINGLE SIDE BAND PHASE NOISE
(typical maximum)
Frequency
Phase Noise
Frequency
Offset
(dBc/Hz) *
Offset
10 Hz
-60
100 Hz
-90
1k Hz
-112
* Results may vary depending on
10k Hz
100k Hz
≥
100k Hz
frequency.
Phase Noise
(dBc/Hz) *
-130
-150
-150
Document No. 008-0244-0
Page 2 - 4
Rev. G
٠ ٠ ٠
CTS Communications Components, Inc.
٠
171 Covington Drive
٠
Bloomingdale, IL 60108
٠
630-924-3500
٠٠٠
7x5mm Low Cost
CMOS/TTL Compatible VCXO
CMOS/TTL OUTPUT WAVEFORM
Tr
Tf
Model 357
TEST CIRCUIT, CMOS LOAD
V
OH
90%, 80%, 2.4V
+
mA
-
4
3
D.U.T.
C
L
2
Including probe
capacitance.
50%, 1.5V
+
POWER
SUPPLY
+
VM
-
.01uF
-
10%, 20%, 0.5V
UPTIME (t)
PERIOD (T)
1
V
OL
Enable Input
DUTY CYCLE = t/T x 100 (%)
D.U.T. PIN ASSIGNMENTS
ENABLE TRUTH TABLE
PIN 2 or Pin 5
Logic ‘1’
Open
Logic ‘0’
PIN 4
Output
Output
High Imp.
PIN
1
2
3
4
5
6
SYMBOL
V
C
EOH or N.C.
GND
Output
N.C. or EOH
V
CC
DESCRIPTION
Control Voltage
Enable or No Connect
Circuit & Package Ground
RF Output
No Connect or Enable
Supply Voltage
MECHANICAL SPECIFICATIONS
PACKAGE DRAWING
(7.0 ±0.2)
0.276 ±0.008
PIN 1 IDENTIFIER
(1.4)
0.055
(1.27)
0.050
(5.0 ±0.2)
0.197 ±0.008
(3.73)
0.147
4
5
6
MARKING INFORMATION
1.
2.
3.
4.
** - Manufacturing Site Code.
YYWW – Date code, YY – year, WW – week.
Truncated CTS part number.
XXXMXXXX - Frequency marked with 4
significant digits after the ‘M’.
CTS ** YYWW
357LB3C
●
XXXMXXXX
3
2
1
(2.54)
0.100
(2.0)
MAX
0.079
(5.08)
0.200
Key:
(mm)
Inch
Termination pads plated with gold (Au).
SUGGESTED SOLDER PAD GEOMETRY
.071 [1.80]
300
SUGGESTED REFLOW PROFILE
Maximum 260°C, 10 seconds
C
BYPASS
6
5
4
200
Typical 245°C
.165 [4.20]
Temp.
(°C)
100
130°C
.079 [2.00]
1
2
.100 [2.54]
.200 [5.08]
Key:
[mm]
Inch
3
0
0
30
60
90
120
150
180
210
240
270
300
Time (Seconds)
C
BYPASS
should be
≥
0.01 uF.
Document No. 008-0244-0
Page 3 - 4
Rev. G
٠ ٠ ٠
CTS Communications Components, Inc.
٠
171 Covington Drive
٠
Bloomingdale, IL 60108
٠
630-924-3500
٠٠٠
7x5mm Low Cost
CMOS/TTL Compatible VCXO
Model 357
TAPE AND REEL INFORMATION
DIMENSIONS IN MILLIMETERS
17.5
Ø13
4.0
8.0
Ø1.50
1.75
2.40
2.10
2.0
120°
8.40
7.90
16.0
Ø60
Ø180
5.70
5.40
DIRECTION OF FEED
Ø23
Device quantity is 1,000 pieces per 180mm reel.
ENVIRONMENTAL SPECIFICATIONS
Temperature Cycle:
Mechanical Shock:
Sinusoidal Vibration:
Gross Leak:
Fine Leak:
Resistance to Solder Heat:
High Temperature Operating Bias:
Frequency Aging:
400 cycles from –55°C to +125°C, 10 minute dwell at each temperature, 1
minute transfer time between temperatures.
1,500g’s, 0.5mS duration, ½ sinewave, 3 shocks each direction along 3
mutually perpendicular planes (18 total shocks).
0.06 inches double amplitude, 10 to 55 Hz and 20g’s, 55 to 2,000 Hz, 3 cycles
each in 3 mutually perpendicular planes (9 times total).
No leak shall appear while immersed in an FC40 or equivalent liquid at
+125°C for 20 seconds.
Mass spectrometer leak rates less than 2x10
-8
ATM cc/sec air equivalent.
Product must survive 3 reflows of +260°C peak, 10 seconds maximum.
2,000 hours at +125°C, maximum bias, disregarding frequency shift.
1,000 hours at +85°C, full bias, less than ±5 ppm shift.
QUALITY AND RELIABILITY
Quality systems meet or exceed the requirements of ISO 9000:2000 standards. Reliability audits are performed on
this or similar products with results available upon request.
The circuit introduced in this article is a practical circuit used for time calibration and meter reading in time-sharing electricity meters. It is simple and practical. Using the asynchronous communi...
I just started learning beaglebone, and now I have written a simplest LED driver, but I encountered the problem of inconsistent kernel versions. Simply put, the kernel version in ti-sdk-am335x-evm-05....
High-intensity discharge lamps (HID) such as high-pressure sodium lamps (HPS) have the characteristics of high light intensity and long life. They are widely used in area lighting applications in publ...
[font=Tahoma][size=14px][size=5]I. The concept of layers in PCB design[/size][/size][/font][p=26, null, left][size=14px][font=Tahoma][size=4]1. Top/Bomttom layer: the top/bottom wiring layer, designed...
The version is 3.2. I have searched for a cracked version on the Internet for a long time but couldn't find it. I can't even find a video on how to use it. If any expert can share a cracked version or...
: I have come to the conclusion that there will be no problem as long as the result on the right side of = does not exceed the range of the data type on the left side. float f = 123.456; uchar a = 0, ...
Wave soldering is a crucial electronic component soldering technique used in the production of a wide range of electronic devices, from home appliances to computers to avionics. The process is wide...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
Is pure electric vehicles a false proposition for long-distance driving? At least from my personal perspective, based on current technological and infrastructure standards, I believe so. Below, I'l...[Details]
Topics: Bring Your Own Device (BYOD) trends; the impact of using employees' own mobile devices to control access to work facilities and equipment on information security; and ways to securely imple...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
On August 20th, Tiantai Robotics Co., Ltd., along with strategic partners including Shandong Future Robotics Technology Co., Ltd., Shandong Future Data Technology Co., Ltd., and Gangzai Robotics Gr...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
Coal mines typically contain gas and coal dust. When gas and coal dust reach a certain concentration, they can cause explosions. Electrical equipment generates arcs during normal operation or durin...[Details]
Compared to cloud databases, minicomputers are purpose-built for decentralized, rugged computing at the edge of the network. By moving applications, analytics, and processing services closer to the...[Details]
Bosch has released a new SoC series to support L2+ advanced driver assistance functions. The chip integrates high resolution and long-range detection capabilities, and has built-in support for neur...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
Charging is an essential topic for electric vehicles. Batteries are a core component of new energy vehicles. So, what's the optimal charge level for electric vehicles? Based on current battery tech...[Details]
Speaking of the problem of vehicle spontaneous combustion, whether it is a pure electric vehicle or a fuel vehicle, there will be incidents of spontaneous combustion. For the same spontaneous combu...[Details]
For new energy vehicles, the importance of batteries is unquestionable. Not only does it determine the performance of the vehicle, but the battery density also has a great relationship with the veh...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
