EEWORLDEEWORLDEEWORLD

Part Number

Search

310-13-123-41-001

Description
IC Socket, SIP23, 23 Contact(s)
CategoryThe connector    socket   
File Size109KB,1 Pages
ManufacturerMill-Max
Websitehttps://www.mill-max.com
Environmental Compliance
Download Datasheet Parametric View All

310-13-123-41-001 Overview

IC Socket, SIP23, 23 Contact(s)

310-13-123-41-001 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerMill-Max
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresSIP SOCKET
Contact to complete cooperationGOLD (30) OVER NICKEL
Contact completed and terminatedGOLD (10) OVER NICKEL
Contact materialNOT SPECIFIED
Device slot typeIC SOCKET
Type of equipment usedSIP23
Shell materialGLASS FILLED POLYETHYLENE POLYESTER
JESD-609 codee4
Manufacturer's serial number310
Number of contacts23
Base Number Matches1
SINGLE-IN-LINE SOCKETS
Solder Tail
Single Row
SIP sockets accept .015 - .025”
diameter pins and standard IC leads.
Various solder tails available:
standard length, long for multi-
layer boards, very low and ultra
low profile. See Mill-Max #1001,
0134, 0501 or 0703 pins (pages
130, 131, 134) for details.
Hi-Rel, 4-finger BeCu #12 & #30
clips rated at 3 amps. See pages
207 & 208 for details.
Series 310, 311, 315
Ordering Information
Fig. 1
Series 310...001
Standard Solder Tail
Fig. 1
310-XX-1_ _-41-001
Specify # of pins
Series 311...001
01-64
Long Solder Tail
Fig. 2
311-XX-1_ _-41-001
Specify # of pins
01-64
Very Low Profile
Fig. 2
Series 315...001
Fig. 3
315-XX-1_ _-41-001
Specify # of pins
Series 315...003
01-64
Ultra Low Profile
Fig. 4
315-XX-1_ _-41-003
Specify # of pins
01-64
Fig. 3
XX= Plating Code
See Below
For High
Temperature
Insulators
Add ‘100’
To End Of
Part Numbers
SPECIFY PLATING CODE XX=
13
10µ” Au
30µ” Au
91
10µ” Au
93
30µ” Au
99
200µ”Sn/Pb
Sleeve (Pin)
200µ” Sn/Pb 200µ” Sn/Pb 200µ”Sn/Pb
Fig. 4
Contact (Clip)
Mill-Max-Mfg.Corp., P.O. Box 300, 190 Pine Hollow Road, Oyster Bay, NY 11771-0300.Tel: 516-922-6000 Fax: 516-922-9253
46
Problems with Linux dynamic loading of driver modules
I am a beginner in driver development and I followed the example to write a simple GPIO driver to control the LED on the development board. However, after dynamically loading the driver, an error was ...
labview Linux and Android
[Evaluation of domestic FPGA Gaoyun GW1N-4 series development board] OLED display
I haven't played around with FPGA for a long time . I was busy moving and joining a new company recently. I only had time to play around with Gowin FPGA these days . Now I use Gowin FPGA to drive OLED...
怀揣少年梦 Domestic Chip Exchange
Signal Attenuator Principle and Design
Signal Attenuator Principle and Design...
btty038 RF/Wirelessly
System Beat
[i=s]This post was last edited by dj狂人 on 2014-12-15 13:54[/i] [align=left] [font=宋体][size=18.0pt]System Beat[/size][/font][/align][align=left][font=宋体][size=18.0pt] [/size][/font][/align][align=left]...
dj狂人 stm32/stm8
A bunch of errors occurred when Orcad exported the netlist. How to solve them?
As shown in the picture, similar to this warning, is renamed..., but I have set the duplicate GND and VCC pins to POWER attributes, why does it still prompt duplicates? What's going on?...
elec32156 PCB Design
Use PCI chips to develop PCI interface boards and related drivers.
I was assigned a task to develop a PCI interface board and related drivers using PCI chips. I know a little bit about C/C++ and VC++, but not much about hardware. I only know a little bit about digita...
chinatonglian Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2795  1008  1061  878  2130  57  21  22  18  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号