0.5A Positive Low Dropout Fixed-Mode Regulator With EN Function
Features
•
•
•
•
•
•
•
General Description
AP1119 is a low dropout positive adjustable or
fixed-mode regulator with minimum of 0.5A output
current capability. The product is specifically
designed to provide well-regulated supply for low
voltage IC applications such as high-speed bus
termination and low current 3.3V logic supply.
AP1119 is also well suited for other applications
such as VGA cards. AP1119 is guaranteed to have
<1.3V dropout at full load current making it ideal to
provide well regulated fixed outputs of 1.5 to 12V
with up to 18V input supply. The AP1119 offers a
TTL – Logic compatible enable pin.
1.3V maximum dropout at full load current
Fast transient response
Output current limiting
Built-in thermal shutdown
Packages: SOT89-5L
Good noise rejection
5-Terminal device with fixed 1.5V, 1.8V, 2.5V,
3.3V, 5.0V, 9.0V, 12V output.
Applications
•
•
•
PC peripheral
Communication
CDROM..
Ordering Information
AP 1119 X XX X X
Low Dropout Regulator
Package
Y : SOT89-5L
Vout
15 : 1.5V
18 : 1.8V
25 : 2.5V
33 : 3.3V
50 : 5.0V
90 : 9.0V
12 : 12V
Lead Free
Blank : Normal
L : Lead Free Package
Packing
Blank : Tube
A : Taping
Typical Circuit
5V
C1
100uF
NC
Tab is Vout
ON OFF
EN
4
3
2
Vin
3.3V/0.5A
Vout
GND
5
1
C2
100uF
( 5V/3.3V fixed output )
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 1.0 Aug 20, 2004
1/5
Not Recommended for New Design
AP1119
0.5A Positive Low Dropout Fixed-Mode Regulator With EN
Function
Connection Diagram
5 PIN SOT89
NC
Tab is Vout
EN
4
3
2
Vin
Vout
GND
5
1
Pin Descriptions
NAME
GND
Vout
Ground
The output of the regulator. A minimum of 10uF capacitor must be connected from this pin
to ground to insure stability.
The input pin of regulator. Typically a large storage capacitor is connected from this pin to
ground to insure that the input voltage does not sag below the minimum dropout voltage
during the load transient response. This pin must always be 1.3V higher than Vout in order
for the device to regulate properly.
The input pin of regulator. TTL/CMOS compatible input Logic high = disable output, Logic
Low or open =Enable output. (internal Pull-down resistor ~ l00K).
FUNCTION
Vin
EN
Absolute Maximum Ratings
Characteristics
DC Supply Voltage
Power Dissipation
Storage Temperature
Operating Junction Temperature Range
Symbol
Vin
P
D
T
ST
T
OP.
Values
-0.3 to 18
Internally Limited
-65 to +150
0 to +150
oC
oC
Unit
V
Anachip Corp.
www.anachip.com.tw
2/5
Rev. 1.0 Aug 20, 2004
Not Recommended for New Design
AP1119
0.5A Positive Low Dropout Fixed-Mode Regulator With EN Function
I don't know much about electronics, but I wanted to make a VGA switch. I used HCF4053 on a perf board to build a simple VGA switch, and it worked (the effect was very poor, with ghosting). So I thoug...
If you have an SDR development board and need it for your project, you can buy it or rent it. The price is negotiable. Your contact information is QQ: 547409723. Please make a note when adding me. Tha...
[i=s] This post was last edited by dontium on 2015-1-23 13:38 [/i] May I ask the experts:LDP #6SPLK #80h, RAMYUis directly addressed, where is its offset?...
In an application, I use STM32 to drive MOS tubes. The drive port is configured as OD output + 10K pull-up. What is the maximum voltage at the other end of the pull-up resistor?I tested it before with...
I use 51 single chip microcomputer to do data acquisition. Does anyone have C program of AD7731? Can you provide reference? I really have no idea. I have been debugging for a long time. My email addre...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
DCDC means DC to DC (conversion of different DC power values). Anything that meets this definition can be called a DCDC converter. Specifically, it means converting the input DC into AC through a s...[Details]
This paper describes the design method of electronic multifunctional watt-hour meter, the key technology of hardware design and the software design process. Taking NEC's μPD78F0338 microcontroller ...[Details]
Preface
DS18B2 is generally used in conjunction with a single-chip microcomputer, and there are few reports on
the interface between
DSP
and DS18B20. Therefore, this article introdu...[Details]
Integrated technical exchanges
京公网安备 11010802033920号
EEWORLD
