39-3681413 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power management> transformer> 39-3681413

39-3681413: DescriptionCurrent Transformer, 1500:5A, 1% Accuracy Class,; CategoryPower management transformer; File Size256KB，3 Pages; ManufacturerC&D

Download Datasheet Parametric View All

39-3681413 Overview

Current Transformer, 1500:5A, 1% Accuracy Class,

39-3681413 Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Reach Compliance Code	unknown
ECCN code	EAR99
Accuracy level	1
Certification	UL; CSA
Rated current (Ip:Is)	1500:5 A
diameter	76.2 mm
high	114.3 mm
Insulation voltage	600 V
Manufacturer's serial number	39-3681413
Installation features	CHASSIS MOUNT
Maximum operating frequency	0.4 kHz
Minimum operating frequency	0.05 kHz
physical size	76.2mm x 114.3mm
primary type	WOUND PRIMARY
Maximum secondary load	12.5 VA
surface mount	NO
Transformer type	CURRENT TRANSFORMER
Base Number Matches	1

Preview

Download Datasheet

View All

DMS Accessories

Order online at www.datel.com

These commercial grade, UL & CSA recognized, “donut

style” AC current-transformers (CT) provide an isolated 0-5A

output that can be used with DATEL’s ACA5 Series of digital

ammeters. Installation is straightforward: simply pass the load-

carrying conductor through the 5A CT’s primary window, and

then route its secondary’s leads through the ACA5-ammeter’s

built-in, low-burden, toroid sensor.

All models feature rugged, fully insulated construction, allow-

ing continuous operation with primary voltages up to 600Vac,

at line frequencies from 50 to 400Hz. Fourteen models are

available to enable accurate measurements from 50A through

2000A. When combined with DATEL’s ACA5 Series ammeters,

secondary lead-extensions may be used for those applications

where the CT cannot be installed in the immediate vicinity of

the ammeter.

General Specifications (All models)

Insulation Class

Frequency Range

Supplied Secondary Leads

600V, 10kV BIL full wave

50-400Hz

Flexible conductors, 24" (61cm)

16AWG (1.8mm

), UL Style 1015, 105°C

See Table 1 and technical note 6

See Table 1

E93779

LR89403

1.0 lbs. (454g)

5 Amp AC

Current Transformers

with DATEL’s ACA5 series ammeters). However, any CT can generate

potentially lethal voltages if its output current is suddenly interrupted.

For example, loose secondary connections can produce a condition

referred to as “inductive kick.” Inductive kick can generate extremely

high voltages across the open secondary connections.

Therefore, all connections made to a CT’s secondary leads must only

be performed with zero current flowing in the primary circuit. Never

operate a CT with its secondary circuit open and current flowing in

the primary.

2. CT Connections and Grounding:

Some applications require con-

necting one of the CT’s 5A output terminals to earth/chassis ground.

In the USA, consult the latest revision of the National Electrical Code

for more information.

After all mechanical assembly is completed, pass the 5A secondary

leads through the ACA5 ammeter’s built-in toroid, then connect the

two leads together as shown in Figure 1. For this connection, and

for connections involving lead extensions, pressure-style connectors

(commonly called “wire nuts”) are acceptable as long as they are rated

for the currents and voltages involved.

3. Installation:

CT’s must be installed in a manner that ensures no

excessive stresses are applied to the primary conductor that passes

through the CT or to the secondary circuit and its associated instru-

ments. Use plastic tie-wraps and/or other suitable non-conductive

restraining devices to secure the CT.

AC POWER

SUPPLY

ACA5-20PC-X-ACX

Max. Secondary Lead Length

See Table 1 and technical note 5

Rated Accuracy

Burden

UL FIle No.

CSA File No.

Weight

Basic Lightning Impulse Insulation Level (BIL): The insulation strength refer-

enced to the crest value of an impulse voltage-waveform which rises to a crest

value in 1.2 microseconds, then drops to 1⁄2 the crest value in 50 microseconds.

Tehnical Notes

IMPORTANT! To ensure safe and reliable operation, Current Trans-

formers and associated equipment must be installed and serviced

by qualified technical personnel. Never open the CT’s secondary

connections while the primary is energized. Open CT secondary

wiring can generate potentially lethal voltages when the primary

circuit is energized. Contact DATEL if you have any doubts

regarding the installation or operation of any of our ac-mains

measurement instruments and accessories.

1. CT Precautions:

In normal operation, a 5A current transformer’s

secondary circuit operates at a relatively low voltage due to its closed-

loop, low burden configuration (essentially zero Ohms when used

TO AC LOAD

TB1

5A CURRENT

TRANSFORMER

(see technical notes)

0-5A

OUTPUT

Figure 1. Typical Connections

DATEL, Inc., Mansfield, MA 02048 (USA)

•

Tel: (508)339-3000, (800)233-2765 Fax: (508)339-6356

•

E–mail: sales@datel.com

•

Internet: www.datel.com

Recommended Resources

VMOS tube high-quality power amplifier circuit

Dangerous speed warning device circuit diagram

Basic circuit diagram of LM2941C

M50111P/AP/By/CF (VCR, TV and audio equipment) 30-function infrared remote control receiving circuit

Direct heating rectifier tube full-wave rectification and filter circuit

Talk about the pressure faced by test engineers: Test engineers, here’s a question: In the past five years, what changes have taken place in your work tasks and intensity? Where does the pressure manifest itself? What are your expectations for futur...; 思潇 Test/Measurement

【TI's First Low Power Design Competition】Energia Installation: [i=s]This post was last edited by ddllxxrr on 2014-10-17 09:05[/i] I downloaded Energia a long time ago, but I was busy with other things these two days and didn't unzip it. I thought it should be ver...; ddllxxrr Microcontroller MCU

I have a question about MOS tube circuit, can you please help?: Make a very simple MOS switch circuit. When these MOS tubes are used as switch circuits, add a resistor between the gate and the source. Some online searches say that it is to ensure the effective and...; yet Power technology

This is a test question used by a company when recruiting new employees...: On a stormy night, you are driving a car and passing a bus station. There are three people waiting for the bus. One is a dying old man, so pitiful. One is a doctor who has saved your life and is a gre...; eeleader Talking about work

Newbie help... OCMJ15X20D LCD display: http://www.ec66.com/market/manual/OCMJ-D.pdf The PDF above, the last paragraph on page 13. It talks about the operation process of the MCU on the LCD module buffer and Display RAM. I would like to ask...; xiangbing Embedded System

Highly recommended: Give old motors new tricks, a motor drive engineer with 34 years of experience shares his experience!: I have been paying attention to the content related to motor drive recently, and I found this course of TI very interesting. The speaker is an engineer with 34 years of experience in motor drive. The ...; soso Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components