EEWORLDEEWORLDEEWORLD

Part Number

Search

3558P15KD0

Description
Board Connector, 15 Contact(s), 3 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size203KB,2 Pages
ManufacturerLeoco USA Corp
Websitehttp://www.leoco.com.tw
Download Datasheet Parametric View All

3558P15KD0 Overview

Board Connector, 15 Contact(s), 3 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

3558P15KD0 Parametric

Parameter NameAttribute value
MakerLeoco USA Corp
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresMATING PIN LENGTH=0.231 INCH
body width0.299 inch
subject depth0.1 inch
body length0.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
contact modeRECTANGULAR
Contact resistance40 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance500000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial number3558
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number3
Number of rows loaded3
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.118 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts15
Base Number Matches1
PFC circuit of ucc28019
In this circuit, replacing the resistor with a potentiometer should be able to adjust the output voltage, right? Why is there no response when I adjust it? The input is 24V, and the output is constant...
夜微微凉 Power technology
Practical settings for ISE to call modelsim for simulation
ISE10.1 and ModelSim6.2b were installed. ISE was installed first, and then ModelSim. I tried several methods but failed to connect. Finally, I used the following method to make ISE able to call ModelS...
eeleader FPGA/CPLD
Why does CCS need to install a driver?
CCS is an open software platform that can support different hardware interfaces, so different hardware interfaces must be connected to CCS through standard drivers. Common problems with driver install...
bolibo123 DSP and ARM Processors
Helio Cyclone V SoC Development Board Application FPGA Getting Started Experience
I would like to share my experience of using the Helio demo board with you. Welcome to ask questions and exchange ideas! Please see the attachment for details. Thank you! wu_zhjun 2015-05-29...
wu_zhjun FPGA/CPLD
Learning Board Tutorial Lesson 4 - Timer
Some basic knowledge and demonstrations of timers, welcome to download, thank you!...
764workshop Integrated technical exchanges
Can the PA3 pin of STM32 be used as PWM output of TIM2?
rt,in this post, the moderator said that CH4 of TIM2 cannot be used for PWM input,https://bbs.eeworld.com.cn/icview-109870-1-1.htmlCan it be used for output? I want to set CH4 of TIM2 as PWM output an...
dld2 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1261  588  1983  2812  1236  26  12  40  57  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号