EEWORLDEEWORLDEEWORLD

Part Number

Search

AZ852N-9DE

Description
MICROMINIATURE POLARIZED RELAY
File Size202KB,4 Pages
ManufacturerETC
Download Datasheet View All

AZ852N-9DE Overview

MICROMINIATURE POLARIZED RELAY

AZ852
MICROMINIATURE
POLARIZED RELAY
FEATURES
Conforms to IEC60950/UL60950/EN60950
spacing and high breakdown voltage
Supplementary insulation
mains voltage 250 Vrms (SMT); 200 Vrms (THT)
Pollution Degree 2 (external); 1 (internal)
Monostable and bistable (latching) coil versions available
High dielectric and surge voltage:
2.5 KV surge (per Bellcore TA–NWT–001089)
2.5 KV surge (per FCC Part 68)
1,000 Vrms, open contacts
Stable contact resistance for low level signal switching
Epoxy sealed
UL, CUR pending
CONTACTS
Arrangement
Ratings
DPDT (2 Form C)
Bifurcated crossbar contacts
Resistive load:
Max. switched power: 60 W or 62.5 VA
Max. switched current: 2.0 A
Max. switched voltage: 220 VDC* or 250 VAC
*
Note: If switching voltage is greater than 30 VDC,
GENERAL DATA
Life Expectancy
Mechanical
Electrical
Operate Time
(typical)
Release Time (typical)
Bounce (typical)
Capacitance
Minimum operations
1 x 10
8
1 x 10
5
at 0.5 A, 125 VAC, Res.
1 x 10
5
at 2.0 A, 30 VDC, Res.
1 ms at nominal coil voltage
1 ms at nominal coil voltage
(with no coil suppression)
At 10 mA contact current
1 ms at operate or release
< 2 pF at 10 KHz - coil to contacts
< 1 pF at 10 KHz - between open contacts
< 2 pF at 10 KHz - between contact sets
See table
Greater than 10% of nominal coil voltage
10
9
ohms min. at 25°C, 500 VDC,
50% RH
At nominal coil voltage
-40°C (-40°F) to 85°C (185°F)
-40°C (-40°F) to 105°C (221°F)
Operational, 20 g, 10–1,000 Hz
Operational, 50 g min., 11 ms
Non-destructive, 500 g min., 0.5 ms
P.B.T. polyester, UL 94 V-0
Tinned copper alloy, P.C.
260°C (500°F)
10 seconds
0.8 grams
50 per plastic tube, 1000 per carton box
1000 per reel, 1000 or 5000 per carton box
special precautions must be taken.
Please contact the factory.
Rated Load
UL/CUR
0.5 A at 125 VAC
2.0 A at 30 VDC
0.24 A at 220 VDC
Palladium Ruthenium; gold clad
< 50 milliohms initially at 20 mV, 10 mA
Material
Resistance
Dielectric Strength
(at sea level)
Dropout
Insulation Resistance
COIL (Polarized)
Power
At Pickup Voltage
(typical)
Max. Continuous
Dissipation
Temperature Rise
79 mW (3–12 VDC)
98 mW (24 VDC)
0.73 W at 20°C (68°F)
At nominal coil voltage
21°C (38°F) (3–12 VDC)
30°C (54°F) (24 VDC)
Max. 115°C (239°F)
Ambient Temperature
Operating
Storage
Vibration
Shock
Enclosure
Terminals
Max. Solder Temp.
Temperature
NOTES
1.
2.
3.
4.
5.
All values at 20°C (68°F).
Relay may pull in with less than “Must Operate” value.
Relay has fixed coil polarity.
Specifications subject to change without notice.
Ultrasonic cleaning is not recommended.
Max. Solder Time
Weight
Packing unit in pcs
ZETTLER
electronics GmbH
Tel. +49 89 800 97 0
Fax +49 89 800 97 200
office@ZETTLERelectronics.com
www.ZETTLERelectronics.com
2005-03-11
Junkersstrasse 3, D-82178 Puchheim, Germany
EU
STM32F4 dual ADC sampling ADC2 no data
I'm recently debugging the STM32F439 board and want to use dual ADCs for simultaneous sampling. I found that the data from ADC1 is normal but there is no data from ADC2. I'd like some advice. Below is...
baixichi stm32/stm8
INTEL's Rosedale2 chip enables high-performance dual-mode fixed-line and mobile WiMAX modems
Ten major WiMAX equipment manufacturers have selected Intel's next-generation WiMAX chip, code-named Rosedale2 , to provide next-generation solutions for WiMAX networks. Rosedale2 is a low-cost system...
JasonYoo RF/Wirelessly
The stm32 CAN port can sometimes send, but sometimes cannot
I'm debugging the CAN port of STM32F303 recently and want to send data. But after the program is written, sometimes the data can be sent out, and the high and low level waveforms can be seen with an o...
zfe001 stm32/stm8
DDR2+ Design Considerations
[align=left][b][font=宋体]About[/font]DDR2[/b][b][font=宋体]Design Description:[/font][/b][/align][align=left] [/align][align=left] [/align][align=left]1 [font=宋体]Chip Selection:[/font]MT47H64M16HR-37E[/a...
qin552011373 ADI Reference Circuit
Top-level instantiation issues in SOPC projects
After generating a project file using SOPC IP core (let's call this top level VIP for now), I want to instantiate the VIP module as a submodule. However, the compilation fails after doing this , and t...
eeleader FPGA/CPLD
RISC-V MCU Development (Part 14): Help and Feedback
In order to help users use the system faster and solve problems encountered during development, MounRiver Studio (MRS) assists users in various ways, including documents, videos, and wizard pages. At ...
Moiiiiilter MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 595  1882  953  628  2667  12  38  20  13  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号