EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-63135-150Q

Description
MIL-STD-1553 Data Bus Transceiver, DDIP-36
CategoryWireless rf/communication    Telecom circuit   
File Size125KB,16 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-63135-150Q Overview

MIL-STD-1553 Data Bus Transceiver, DDIP-36

BUS-63135-150Q Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerData Device Corporation
Parts packaging codeDIP
package instructionDDIP-36
Contacts36
Reach Compliance Codecompliant
JESD-30 codeR-XDIP-P36
JESD-609 codee0
length43.2 mm
Negative supply voltage rating-15 V
Number of functions1
Number of terminals36
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package body materialUNSPECIFIED
encapsulated codeDIP
Package shapeRECTANGULAR
Package formIN-LINE
Peak Reflow Temperature (Celsius)NOT SPECIFIED
Certification statusNot Qualified
Maximum seat height5.3 mm
surface mountNO
Telecom integrated circuit typesMIL-STD-1553 DATA BUS TRANSCEIVER
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formPIN/PEG
Terminal pitch2.54 mm
Terminal locationDUAL
Maximum time at peak reflow temperatureNOT SPECIFIED
width15.24 mm
Base Number Matches1
BUS-63100 SERIES
MIL-STD-1553 DATA BUS
SINGLE AND DUAL TRANSCEIVERS
BUS-63102
BUS-63105
BUS-63125
DESCRIPTION
The BUS-63100 transceivers are
complete transmitter and receiver
pairs conforming fully to MIL-STD-
1553A and 1553B. Features available
with selected models of this high reli-
ability series include: Smiths and
Harris interface type choices,
+12 V/+15 V power supply voltage
range, variable threshold levels, and
single (24-pin DDIP or square) and
completely independent dual redun-
dant (36-pin DDIP) packaging config-
urations. All models are also available
in flat packs.
The receiver section of the BUS-
63100 series accepts phase-modula-
ted bipolar data from a MIL-STD-1553
Data Bus and produces TTL signal
data at its outputs: RX Data Out and
RX Data Out. These outputs repre-
sent positive and negative variations
of the input data signals beyond an
internally fixed or externally set
threshold level. An external STROBE
input enables or disables the receiver
outputs.
The transmitter section accepts bipo-
lar TTL signal data at its TX Data and
TX Data input lines and produces
phase modulated bipolar data at the
TX Data and TX Data outputs. The
transmitters’ output voltage level is
typically 28 Vpp to 30 Vpp. An exter-
nal input, INHIBIT, takes priority over
the transmitter inputs and disables
the transmitter when activated with a
logic “1.”
The small size and different model
capabilities available with the
BUS-63100 series simplify engineer-
ing design, making it an excellent
choice for interfacing with any
MIL-STD-1553 system.
FEATURES
Conforms Fully to MIL-STD-1553A
and 1553B
Some Models Available to Military
(DESC) Drawings
Model Capabilities:
Single or Dual Redundant
Packaging
-12 V/-15 V Power Supply Voltage
Range Available
Harris or Smith’s I/O Compatibility
Small Size:
Single – 24-Pin DDIP or Square
Dual – 36-Pin DDIP Flat Packs
Low Power
High Reliability – LSI
±V
1553
DATA
BUS
+5 V
RECEIVER STROBE
BI PHASE
TTL DATA
PHASE MODULATED
BIPOLAR DATA
RX Data In
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX Data In
RECEIVER SECTION
COMPARATOR
RX Data
LIMITER
FILTER
RX Data
DECODER
COMPARATOR
TRANSMITTER SECTION
DRIVER
TX Data Out
SHAPING
NETWORK
DRIVER
TX Data Out
SHAPING
NETWORK
TX Data In
TX Data In
ENCODER
TX INHIBIT
FIGURE 1. BUS-63100 BLOCK DIAGRAM
M
DDC Custom Monolithics utilized in this product are copyright under the Semiconductor chip Protection Act.
[Shanghai Hangxin ACM32F070 development board + touch function evaluation board evaluation] + UART and ultrasonic ranging
The ACM32F070 development board is equipped with 3 serial ports, and their pin assignments and baud rate settings are as follows:UART1: Printing and debugging serial port, supports printf, pins: A9:Tx...
jinglixixi Domestic Chip Exchange
How to use ip and fifo together?
I am designing an IP (avalon interface), and I plan to use two fifos, one for writing and one for reading. For example, for USB, the function of this IP is to put data into the fifo when it comes, and...
liwenz FPGA/CPLD
iMX6 Series Application Notes - One article teaches you how to use iMX6Q GPIO functions
This article is based on the Feiling embedded OKMX6Q/DL-C development board. The operating system is Linux3.0.35. For other brands of products, please refer to it. This article mainly introduces the o...
小螃蟹呀 ARM Technology
WindowsCE SDK Development
What does windowsCE SDK development mean? Isn't SDK exported in PB?...
lizengmao Embedded System
[All the experts are here] High-end seminar on industrial 4.0 and robots--EEWORLD University Hall
Industrial 4.0 Robotics High-end Seminar : https://training.eeworld.com.cn/course/2091 [size=4]Many professors and experts in the field of robotics at MIT shared their experiences on robot design, mob...
chenyy Robotics Development
Detailed explanation of the production method of double-sided board hole metallization
The printed circuit board processing plant uses automated continuous operation equipment, which is expensive and impossible to do under amateur conditions. What we are introducing here is a method tha...
kandy2059 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2321  992  2296  1474  63  47  20  30  2  51 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号