EEWORLDEEWORLDEEWORLD

Part Number

Search

BUS-855920

Description
Telecom IC
CategoryWireless rf/communication    Telecom circuit   
File Size55KB,4 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BUS-855920 Overview

Telecom IC

BUS-855920 Parametric

Parameter NameAttribute value
MakerData Device Corporation
package instruction,
Reach Compliance Codeunknown
Base Number Matches1
BUS-8559
VARIABLE OUTPUT
MIL-STD-1553 TRANSCEIVER
FEATURES
coupled to the data bus with the spec-
ified transformer*, and isolated (on the
data side) with two 55
fault isolation
resistors, and loaded with two 70
terminations
(plus
additional
receivers), the data bus signal pro-
duced is a nominal 0 to 7.5 V pk-pk
when measured at the output side of
the 55
resistors.
When both DATA and DATA, inputs
are held low or high, the transmitter
presents a high impedance to the
line. An external inhibit input is also
provided, which allows the the trans-
mitter output to be removed from the
line.. When a logic “1” is applied to the
TX INHIBIT input, the transmitter is
disabled, and the data inputs are
ignored.
DESCRIPTION
Designed specifically for use in auto-
matic test equipment where a variable
transmitter output level is required,
the DDC Model BUS-8559 transceiv-
er is a complete transmitter and
receiver conforming to MIL standards
1553A and 1553B.
The receiver section accepts phase-
modulated bipolar data at the input
and produces a bi-phase TTL signal
at the output, see FIGURE 1.
Outputs, DATA and DATA, are posi-
tive and negative excursions of the
input beyond an internally fixed
threshold. The positive and negative
thresholds are internally set at the
factory for a nominal 1 V pk-pk signal,
when measured at point “A” in FIG-
URE 2. An external strobe input is
provided which allows the the receiv-
er to be removed from the line. A logic
“0” applied to RECEIVER STROBE
will disable the receiver output.
The BUS-8559 transmitter section
accepts bi-phase TTL data at the
input and produces a nominal 0 to 27
V pk-pk differential output across a
145
load. When the transmitter is
Variable Transmitter Output
Transmitter/Receiver in a Single
24-Pin DDIP Hybrid
Very Low Power Dissipation
Improved Receiver Filtering
Enhances System Bit Error Rate
Meets MIL-STD-1553A and 1553B
Power Supplies:
±15 V or
+15 V and -12 V
APPLICATION
The BUS-8559 is suitable for any
MIL-STD-1553 application which
requires a transceiver. The BUS-8559
comes in a hermetic, 24-pin DDIP
package which measures 1.4 x 0.8 x 0.2
inches.
-15
+15
+5
VAR VCC
(O to +15 V)
BUS-8559
TRANSCEIVER
COMPARATOR
RECEIVER
STROBE
RX DATA
LIMITER
FILTER
RX DATA
COMPARATOR
SHAPING
NETWORK
DRIVER
DATA
SHAPING
NETWORK
TX DATA
TX INHIBIT
TX DATA
BUS-25679
TRANSFORMER
DATA
DRIVER
BUS-8559 BLOCK DIAGRAM
©
1999 Data Device Corporation
Introduction: TI Stellaris LM3S8962 Ethernet + CAN Evaluation Board
The StellarisLM3S8962 Ethernet+CAN Evaluation Board is a general evaluation platform based on the Stellaris LM3S8962 ARMCortex -M3 core microcontroller, supporting software, hardware and development e...
soso Microcontroller MCU
EMI filter design
...
czf0408 Power technology
A well-known communication company in Beijing is recruiting DSP software engineers
DSP Software Engineer Annual Salary 16-19W Job Responsibilities: 1. Responsible for the verification and implementation of the physical layer algorithm of the wireless system products of the broadband...
e1065037772 Recruitment
Love electronics for three to five years
I haven't written anything for a long time. On the one hand, it's because I've been busy for more than a year. On the other hand, I always feel that I haven't done anything for more than a year, and I...
zjd01 Talking
51 advertising light digital tube and MSP430 digital tube
I originally wanted to implement a switch, but I recently dragged it so I added some functions. This function is to move the advertising light left and right, but I added an input that can switch a si...
tiankai001 Microcontroller MCU
I modified WINCE500\PUBLIC\COMMON\OAK\DRIVERS\TOUCH\TCHMAIN\tchmain.c, but why is the corresponding generated touch.dl
It stands to reason that if I "build current project" for the above project, the corresponding dll should be generated, but it is not. Why? What should I do?...
laopo163 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2287  794  2380  570  2113  47  16  48  12  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号