EEWORLDEEWORLDEEWORLD

Part Number

Search

M29W400B-90ZA5R

Description
4 Mbit 512Kb x8 or 256Kb x16, Boot Block Low Voltage Single Supply Flash Memory
Categorystorage    storage   
File Size223KB,34 Pages
ManufacturerSTMicroelectronics
Websitehttp://www.st.com/
Download Datasheet Parametric View All

M29W400B-90ZA5R Overview

4 Mbit 512Kb x8 or 256Kb x16, Boot Block Low Voltage Single Supply Flash Memory

M29W400B-90ZA5R Parametric

Parameter NameAttribute value
MakerSTMicroelectronics
Parts packaging codeBGA
package instruction0.80 MM PITCH, FBGA-48
Contacts48
Reach Compliance Codeunknow
ECCN codeEAR99
Maximum access time90 ns
Other featuresBOTTOM BOOT BLOCK
Spare memory width8
startup blockBOTTOM
JESD-30 codeR-PBGA-B48
length9 mm
memory density4194304 bi
Memory IC TypeFLASH
memory width16
Number of functions1
Number of terminals48
word count262144 words
character code256000
Operating modeASYNCHRONOUS
Maximum operating temperature85 °C
Minimum operating temperature-20 °C
organize256KX16
Package body materialPLASTIC/EPOXY
encapsulated codeLFBGA
Package shapeRECTANGULAR
Package formGRID ARRAY, LOW PROFILE, FINE PITCH
Parallel/SerialPARALLEL
Programming voltage3 V
Certification statusNot Qualified
Maximum seat height1.35 mm
Maximum supply voltage (Vsup)3.6 V
Minimum supply voltage (Vsup)3 V
Nominal supply voltage (Vsup)3.3 V
surface mountYES
technologyCMOS
Temperature levelOTHER
Terminal formBALL
Terminal pitch0.8 mm
Terminal locationBOTTOM
typeNOR TYPE
width6 mm
M29W400T
M29W400B
4 Mbit (512Kb x8 or 256Kb x16, Boot Block)
Low Voltage Single Supply Flash Memory
NOT FOR NEW DESIGN
M29W400T and M29W400B are replaced
respectively by the M29W400BT and
M29W400BB
2.7V to 3.6V SUPPLY VOLTAGE for
PROGRAM, ERASE and READ OPERATIONS
FAST ACCESS TIME: 90ns
FAST PROGRAMMING TIME
– 10µs by Byte / 16µs by Word typical
PROGRAM/ERASE CONTROLLER (P/E.C.)
– Program Byte-by-Byte or Word-by-Word
– Status Register bits and Ready/Busy Output
MEMORY BLOCKS
– Boot Block (Top or Bottom location)
– Parameter and Main blocks
BLOCK, MULTI-BLOCK and CHIP ERASE
MULTI BLOCK PROTECTION/TEMPORARY
UNPROTECTION MODES
ERASE SUSPEND and RESUME MODES
– Read and Program another Block during
Erase Suspend
LOW POWER CONSUMPTION
– Stand-by and Automatic Stand-by
100,000 PROGRAM/ERASE CYCLES per
BLOCK
20 YEARS DATA RETENTION
– Defectivity below 1ppm/year
ELECTRONIC SIGNATURE
– Manufacturer Code: 0020h
– Device Code, M29W400T: 00EEh
– Device Code, M29W400B: 00EFh
DESCRIPTION
The M29W400 is a non-volatile memory that may
be erased electrically at the block or chip level and
programmed in-system on a Byte-by-Byteor Word-
by-Word basis using only a single 2.7V to 3.6V V
CC
supply. For Program and Erase operations the
necessary high voltages are generated internally.
The device can also be programmed in standard
programmers.
The array matrix organisation allows each block to
be erased and reprogrammed without affecting
other blocks. Blocks can be protected against pro-
graming and erase on programming equipment,
November 1999
44
1
TSOP48 (N)
12 x 20 mm
SO44 (M)
BGA
FBGA48 (ZA)
8 x 6 solder balls
Figure 1. Logic Diagram
VCC
18
A0-A17
W
E
G
RP
M29W400T
M29W400B
15
DQ0-DQ14
DQ15A–1
BYTE
RB
VSS
AI02065
1/34
This is information on a product still in productionbut not recommended for new designs.
R7F0C80212 kit trial development environment construction 2---code automatic generation tool code generator
[i=s]This post was last edited by yang_alex on 2014-9-8 08:05[/i] Development Environment Construction for R7F0C80212 Kit Trial 2 --- Code Generator I have seen several automatic code generators from ...
yang_alex Renesas Electronics MCUs
How to set up GPRS modem dial-up in Windows XP?
Under Windows XP, I have a GPRS modem connected via a serial port. At the same time, there is a phone modem on the PC. Every time I set "connect using a dial-up modem", the phone modem is always autom...
lemonnofeeling Embedded System
How to set ADC reference voltage?
The ADC gets the voltage value of a certain point, the range is only 0~1.65v, isn't the internal reference voltage of M4 3.3v? I used ADCReferenceSet (ADC0_BASE,ADC_REF_INT); but the result is useless...
G_Masker Microcontroller MCU
[Ufun learning part 1] unboxing and SWD debugging
I just returned to school a few days ago, and the courier kept urging me to deliver the board. If I came back a few days later, this cute little board would have to say goodbye to me. I couldn't wait ...
shannon2014 stm32/stm8
Design of heterogeneous pads in AD9
As shown below, QFN-10 package, center thermal pad. The heterogeneous pad cannot be drawn. In PCB, use wire to draw the shape, and then convert it to region. When copied to the package editing interfa...
呜呼哀哉 PCB Design
Help
I am using the ordinary I/O of the microcontroller to simulate IIC, writing one byte to the E2PROM, and then reading it out for verification. It works, but there is an error. I don't know if it is a r...
gaorenxiang MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2050  2464  884  2928  1775  42  50  18  59  36 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号