EEWORLDEEWORLDEEWORLD

Part Number

Search

M27V512-150F6TR

Description
512 Kbit 64Kb x8 Low Voltage UV EPROM and OTP EPROM
File Size99KB,16 Pages
ManufacturerSTMicroelectronics
Websitehttp://www.st.com/
Download Datasheet View All

M27V512-150F6TR Overview

512 Kbit 64Kb x8 Low Voltage UV EPROM and OTP EPROM

M27V512
512 Kbit (64Kb x8) Low Voltage UV EPROM and OTP EPROM
s
LOW VOLTAGE READ OPERATION:
3V to 3.6V
FAST ACCESS TIME: 100ns
LOW POWER CONSUMPTION:
– Active Current 10mA at 5MHz
– Standby Current 10µA
28
28
s
s
s
s
s
PROGRAMMING VOLTAGE: 12.75V
±
0.25V
PROGRAMMING TIME: 100µs/byte (typical)
ELECTRONIC SIGNATURE
– Manufacturer Code: 20h
– Device Code: 3Dh
1
1
FDIP28W (F)
PDIP28 (B)
DESCRIPTION
The M27V512 is a low voltage 512 Kbit EPROM
offered in the two ranges UV (ultra viloet erase)
and OTP (one time programmable). It is ideally
suited for microprocessor systems and is orga-
nized as 65,536 by 8 bits.
The M27V512 operates in the read mode with a
supply voltage as low as 3V. The decrease in op-
erating power allows either a reduction of the size
of the battery or an increase in the time between
battery recharges.
The FDIP28W (window ceramic frit-seal package)
has transparent lid which allows the user to ex-
pose the chip to ultraviolet light to erase the bit pat-
tern. A new pattern can then be written to the
device by following the programming procedure.
For applications where the content is programmed
only one time and erasure is not required, the
M27V512 is offered in PDIP28, PLCC32 and
TSOP28 (8 x 13.4 mm) packages.
Table 1. Signal Names
A0-A15
Q0-Q7
E
GV
PP
V
CC
V
SS
Address Inputs
Data Outputs
Chip Enable
Output Enable
Supply Voltage
Ground
PLCC32 (K)
TSOP28 (N)
8 x 13.4mm
Figure 1. Logic Diagram
VCC
16
A0-A15
8
Q0-Q7
E
GVPP
M27V512
VSS
AI00732B
May 1998
1/16
Ti DSP optimization basic strategy
[size=4]1. The optimization process is generally divided into three stages. [/size] [size=4] [/size] [size=4] Stage 1: Implement functions directly in C language as needed. In actual DSP applications,...
fish001 DSP and ARM Processors
Current Source
[i=s]This post was last edited by paulhyde on 2014-9-15 08:52[/i]I designed a current source, but it can only output less than 200 mA. I want a higher current, what should I do?...
gonghuomu Electronics Design Contest
Inductor Design Software
Inductor design software, downloaded from somewhere else....
jinpost RF/Wirelessly
How to set IP?
I am a newbie, I want to know how to set IP in WinCE. After searching for a long time, I found that I need to modify the registry. But I can't even open the registry. I use VS2003 for development. I w...
marchz Embedded System
High score! How to add timeout processing to the serial port reception in 51?
I need to use 2051 to receive data from PC (the length is uncertain, but the length information is in the first byte received). I plan to use method 1, timer 2. If the serial port times out, it means ...
请求权 Embedded System
How to convert between subseconds and seconds?
What is the conversion relationship between subseconds and seconds in the RTC clock of STM32? Thank you!...
tyc119514155 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2685  232  278  773  1917  55  5  6  16  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号