EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV42C-80M-FREQ

Description
LVCMOS Output Clock Oscillator, 50.01MHz Min, 200MHz Max, ROHS COMPLIANT, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size145KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GV42C-80M-FREQ Overview

LVCMOS Output Clock Oscillator, 50.01MHz Min, 200MHz Max, ROHS COMPLIANT, SMD, 4 PIN

3GV42C-80M-FREQ Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerEuroquartz
Reach Compliance Codecompliant
Maximum control voltage1.85 V
Minimum control voltage1.45 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
frequency stability100%
linearity10%
Installation featuresSURFACE MOUNT
Maximum operating frequency200 MHz
Minimum operating frequency50.01 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVCMOS
Output load15 pF
physical size11.4mm x 9.6mm x 2.5mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
Base Number Matches1
EURO
QUARTZ
CMOS SMD 11.4 x 9.6 x 2.5mm, 4 pad
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
OUTLINE & DIMENSIONS
DESCRIPTION
GV42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. The VCXO incorporates a high Q
fundamental mode crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
GV42 VCXO
50.01MHz ~ 200.0MHz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
See table below
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
See table
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (An
increase of control voltage
always increases output
frequency.)
-50° to +100°C
±5ppm per year maximum
Not available (4
pad package)
Fully compliant
PHASE NOISE
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
3GV42B-80N-155.25
Supply Voltage
3 = +3.3V
Series Designator
GV42
Stability over
temperature range (See
table)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
The difference between reduced instruction set and complex instruction set
RISC (Reduced Instruction Set Computer) and CISC (Complex Instruction Set Computer) are two architectures of current CPUs. The difference between them lies in different CPU design concepts and methods...
Jacktang Microcontroller MCU
If the temperature is too high during manual soldering of Ferroelectric's MSP430, will the data be lost or damaged?
Watch the video of the 430FR5739 series. If the temperature is too high during manual soldering, will it cause data loss, shorten the effective time, or damage the device and make it unusable? The vid...
wangfuchong Microcontroller MCU
Recruiting AE (Application Engineer) Manager - Motor Drive Direction 20-25K/month*14
Shenzhen Tingbao Technology Co., Ltd. is recruiting~!Position Title: AE (Application Engineer) Manager - Motor DriveSalary range: 20-25K/month*14Work Location: ShenzhenJob Responsibilities: 1. Respons...
Teampo Recruitment
Which mode should the USBOTG pin be set to when initializing?
I want to use the USB OTG of STM32F105VC and plan to use the master mode. When initializing USBDM and USBDP , what mode should I choose for GPIO_InitStructure.GPIO_Mode?typedef enum{ GPIO_Mode_AIN = 0...
dangelzsp stm32/stm8
Please advise, how to use inductors and capacitors to attenuate the output of the power amplifier (instead of resistor attenuation)
I have a question. I have an amplifier with an output of 100W, but the output S22 is a little bit below the standard, mainly because the bandwidth is too large. I tried 3dB attenuation with resistors ...
voco_2000 RF/Wirelessly
Makefile Problems
[i=s]This post was last edited by chenbingjy on 2016-9-19 13:28[/i] [color=#333333]There is a project file list as follows. There are 5 files in the project. In the add directory, there are add_int.c ...
chenbingjy Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2448  2692  1992  77  2798  50  55  41  2  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号