EEWORLDEEWORLDEEWORLD

Part Number

Search

306-043-520-108

Description
Card Edge Connector,
CategoryThe connector    The connector   
File Size672KB,6 Pages
ManufacturerEDAC
Download Datasheet Parametric View All

306-043-520-108 Online Shopping

Suppliers Part Number Price MOQ In stock  
306-043-520-108 - - View Buy Now

306-043-520-108 Overview

Card Edge Connector,

306-043-520-108 Parametric

Parameter NameAttribute value
MakerEDAC
Reach Compliance Codecompliant
Connector typeCARD EDGE CONNECTOR
Base Number Matches1
306/316/356 SERIES CARD EDGE CONNECTOR
.156" (3.96mm) Contact Spacing
Example Part Number 306 - 022 - 521 - 178
Series
Total Number of Contacts
Contact Code
Mounting Options
Series
306
316
356
Insulator Colour
Card Slot Length
Green
Standard Length per MIL-C-21097
Green
.020 (0.51) Shorter than Standard
Black
Standard Length per MIL-C-21097
Contact Row
Centre Row
306/316/356 SERIES ORDERING CODE
Total Number of Contacts
1
006, 007,...043
Contact Code
2
Description & Tail Size
Tail Length "G"
Wire Hole.087 x .015 (2.21 x 0.38)
.282 (7.16)
500
P.C. Tail .046 x .015 (1.17 x 0.38)
.213 (5.41)
520
521
P.C. Tail .037 x .015 (0.94 x 0.38)
.125 (3.18)
FEATURES
306/356 Series CSA Approved and UL Recognized
316 Series UL Recognized
.156 (3.96) Contact Spacing with Single Centreline Row
Accepts .062 (1.57) Nominal Thickness P.C. Board
Low Profile Insulator Body, .460 (11.68)
Contact Termination Options include P.C. Tail & Wire Hole
Large Variety of Mounting Options
Pre-assembled Card Guides Available
Accepts Between Contact and In-Contact Polarizing Keys
Mounting Options
3
101
102
103
104
107
108
158
168
178
Description
No Mounting Lugs
.128 (3.25) Dia. Mounting Holes
.116 (2.95) I.D. Floating Eyelets
.156 (3.96) Dia. Mounting Holes
M3-0.5 Metric Threaded Inserts
#4-40 Unified Threaded Inserts
.468 (11.89) Offset Card Guides
.344 (8.74) Offset Card Guides
In-Line Card Guides
Insulator Material: Thermoplastic Polyester, UL 94V-0
Contact Material: Copper, Nickel, Tin Alloy CA-725
Contact Plating: Gold on the Mating Area, Tin on the
Contact Tails, Nickel Underplate
Current Rating: 5 Amperes Continuous
Contact Resistance: 10 Milliohms Maximum
Dielectric Withstanding Voltage: 1800 V AC rms at Sea Level
Between Adjacent Contacts
Insulation Resistance: 5000 Megohms Minimum
Operating Temperature: -65 to +105 Degrees C
Insertion Force: 16 oz (4.45 N) Maximum per Contact when
Tested with a .070 (1.78) Thick Gauge
Withdrawal Force: 1 oz (0.28 N) Minimum per Contact when
Tested with a .054 (1.37) Thick Gauge
SPECIFICATIONS
Ordering Code Notes
1) All connector sizes up to 43 contacts centre row are available
upon request.
2) For contacts with overall tin-lead plating, change the first digit
of the contact code from 5 to 4.
3) For details of the mounting options, refer to page 68.
Page 38
Tel: (416) 754 - 3322
I went to Shangzhuang Reservoir today to check out the activities next week~~
It was windy, so there weren't many people when I went there at about 1pm. However, due to the rain a few days ago, the water level was obviously much higher than before, and under the effect of the w...
soso Talking
【Transfer】Share Wince600's memory viewing tool
Reposting the content of a non-technical post: Due to the limited permissions of the AP under CE6, it is difficult to see the status of the memory of the physical address and kernel address space. The...
rolim Embedded System
sysgen issues
I added a driver to BSP. It worked fine when I built it separately before. Today, when I ran sysgen and compiled it to the driver directory, many errors occurred, and all of them were problems with sy...
tianix Embedded System
About stop bit 2
In the 51 communication process, if there are 2 stop bits on the computer, how to set them on the microcontroller? In both mode 2 and mode 3, there is 1 start bit, 8 data bits, 1 programmable bit, and...
周新眼 Embedded System
What should I do if Quartus cannot open Modelsim simulation?
I am a beginner at FPGA. I have installed and cracked Modelsim. But when I try to simulate, this happens. The path is clearly set. Why doesn't it work? As shown in the figure...
扶摇- FPGA/CPLD
A novice needs help and wants to understand the connection between EVC and ActiveSync
I want to use ActiveSync to check the results of the program in EVC, but I can't connect. It always says timeout. I have selected POCKET PC2003, but it still doesn't work. Please give me some advice. ...
fruitivy Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1388  576  642  1255  451  28  12  13  26  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号