NX3L1G3157
Low-ohmic single-pole double-throw analog switch
Rev. 10 — 7 August 2012
Product data sheet
1. General description
The NX3L1G3157 is a low-ohmic single-pole double-throw analog switch suitable for use
as an analog or digital 2:1 multiplexer/demultiplexer. It has a digital select input (S), two
independent inputs/outputs (Y0 and Y1) and a common input/output (Z). Schmitt trigger
action at the digital input makes the circuit tolerant to slower input rise and fall times.
The NX3L1G3157 allows signals with amplitude up to V
CC
to be transmitted from Z to Y0
or Y1; or from Y0 or Y1 to Z. Its low ON resistance (0.5
)
and flatness (0.13
)
ensures
minimal attenuation and distortion of transmitted signals.
2. Features and benefits
Wide supply voltage range from 1.4 V to 4.3 V
Very low ON resistance:
1.6
(typical) at V
CC
= 1.4 V
1.0
(typical) at V
CC
= 1.65 V
0.55
(typical) at V
CC
= 2.3 V
0.50
(typical) at V
CC
= 2.7 V
0.50
(typical) at V
CC
= 4.3 V
Break-before-make switching
High noise immunity
ESD protection:
HBM JESD22-A114F Class 3A exceeds 7500 V
MM JESD22-A115-A exceeds 200 V
CDM AEC-Q100-011 revision B exceeds 1000 V
IEC61000-4-2 contact discharge exceeds 8000 V for switch ports
CMOS low-power consumption
Latch-up performance exceeds 100 mA per JESD78 Class II Level A
Direct interface with TTL levels at 3.0 V
Control input accepts voltages above supply voltage
High current handling capability (350 mA continuous current under 3.3 V supply)
Specified from
40 C
to +85
C
and from
40 C
to +125
C
NXP Semiconductors
NX3L1G3157
Low-ohmic single-pole double-throw analog switch
3. Applications
Cell phone
PDA
Portable media player
4. Ordering information
Table 1.
Ordering information
Package
Temperature range
NX3L1G3157GW
NX3L1G3157GM
40 C
to +125
C
40 C
to +125
C
Name
SC-88
XSON6
Description
plastic surface-mounted package; 6 leads
plastic extremely thin small outline package; no leads;
6 terminals; body 1
1.45
0.5 mm
Version
SOT363
SOT886
Type number
5. Marking
Table 2.
Marking codes
[1]
Marking code
MJ
MJ
Type number
NX3L1G3157GW
NX3L1G3157GM
[1]
The pin 1 indicator is located on the lower left corner of the device, below the marking code.
6. Functional diagram
Y1
S
Z
S 6
1 Y1
Z 4
3 Y0
001aac354
001aac355
Y0
Fig 1.
Logic symbol
Fig 2.
Logic diagram
NX3L1G3157
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 10 — 7 August 2012
2 of 22
NXP Semiconductors
NX3L1G3157
Low-ohmic single-pole double-throw analog switch
7. Pinning information
7.1 Pinning
NX3L1G3157
NX3L1G3157
Y1
GND
1
2
6
5
S
GND
V
CC
Y0
Y0
3
001aai592
Y1
1
6
S
2
5
V
CC
3
4
Z
4
Z
001aag562
Transparent top view
Fig 3.
Pin configuration SOT363 (SC-88)
Fig 4.
Pin configuration SOT886 (XSON6)
7.2 Pin description
Table 3.
Symbol
Y1
GND
Y0
Z
V
CC
S
Pin description
Pin
1
2
3
4
5
6
Description
independent input or output
ground (0 V)
independent input or output
common output or input
supply voltage
select input
8. Functional description
Table 4.
Input S
L
H
[1]
H = HIGH voltage level; L = LOW voltage level.
Function table
[1]
Channel on
Y0
Y1
NX3L1G3157
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 10 — 7 August 2012
3 of 22
NXP Semiconductors
NX3L1G3157
Low-ohmic single-pole double-throw analog switch
9. Limiting values
Table 5.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
V
CC
V
I
V
SW
I
IK
I
SK
I
SW
Parameter
supply voltage
input voltage
switch voltage
input clamping current
switch clamping current
switch current
V
I
<
0.5
V
V
I
<
0.5
V or V
I
> V
CC
+ 0.5 V
V
SW
>
0.5
V or V
SW
< V
CC
+ 0.5 V;
source or sink current
V
SW
>
0.5
V or V
SW
< V
CC
+ 0.5 V;
pulsed at 1 ms duration, < 10 % duty cycle;
peak current
T
stg
P
tot
[1]
[2]
[3]
Conditions
select input S
[1]
[2]
Min
0.5
0.5
0.5
50
-
-
-
Max
+4.6
+4.6
-
50
350
500
Unit
V
V
mA
mA
mA
mA
V
CC
+ 0.5 V
storage temperature
total power dissipation
T
amb
=
40 C
to +125
C
[3]
65
-
+150
250
C
mW
The minimum input voltage rating may be exceeded if the input current rating is observed.
The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not
exceed 4.6 V.
For SC-88 package: above 87.5
C
the value of P
tot
derates linearly with 4.0 mW/K.
For XSON6 package: above 118
C
the value of P
tot
derates linearly with 7.8 mW/K.
10. Recommended operating conditions
Table 6.
V
CC
V
I
V
SW
T
amb
t/V
[1]
Recommended operating conditions
Conditions
select input S
[1]
Symbol Parameter
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise and fall rate
Min
1.4
0
0
40
-
Max
4.3
4.3
V
CC
+125
200
Unit
V
V
V
C
ns/V
V
CC
= 1.4 V to 4.3 V
[2]
To avoid sinking GND current from terminal Z when switch current flows in terminal Yn, the voltage drop across the bidirectional switch
must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current flows from terminal Yn. In this case, there is no limit for
the voltage drop across the switch.
Applies to control signal levels.
[2]
NX3L1G3157
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 10 — 7 August 2012
4 of 22
NXP Semiconductors
NX3L1G3157
Low-ohmic single-pole double-throw analog switch
11. Static characteristics
Table 7.
Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter
Conditions
Min
V
IH
HIGH-level
input voltage
V
CC
= 1.4 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 2.7 V to 3.6 V
V
CC
= 3.6 V to 4.3 V
V
IL
LOW-level
input voltage
V
CC
= 1.4 V to 1.95 V
V
CC
= 2.3 V to 2.7 V
V
CC
= 2.7 V to 3.6 V
V
CC
= 3.6 V to 4.3 V
I
I
input leakage
current
OFF-state
leakage
current
select input S;
V
I
= GND to 4.3 V;
V
CC
= 1.4 V to 4.3 V
Y0 and Y1 port;
see
Figure 5
V
CC
= 1.4 V to 3.6 V
V
CC
= 3.6 V to 4.3 V
I
S(ON)
ON-state
leakage
current
Z port; see
Figure 6
V
CC
= 1.4 V to 3.6 V
V
CC
= 3.6 V to 4.3 V
-
-
-
-
5
10
-
-
50
50
500
500
nA
nA
-
-
-
-
5
10
-
-
50
50
500
500
nA
nA
0.65V
CC
1.7
2.0
0.7V
CC
-
-
-
-
-
T
amb
= 25
C
Typ
-
-
-
-
-
-
-
-
-
Max
-
-
-
-
0.35V
CC
0.7
0.8
0.3V
CC
-
T
amb
=
40 C
to +125
C
Min
0.65V
CC
1.7
2.0
0.7V
CC
-
-
-
-
-
Max
Max
(85
C)
(125
C)
-
-
-
-
0.7
0.8
0.3V
CC
0.5
-
-
-
-
0.7
0.8
1
V
V
V
V
V
V
A
Unit
0.35V
CC
0.35V
CC
V
0.3V
CC
V
I
S(OFF)
I
CC
supply current V
I
= V
CC
or GND;
V
SW
= GND or V
CC
V
CC
= 3.6 V
V
CC
= 4.3 V
-
-
-
-
-
-
-
1.0
35
130
100
150
-
-
-
-
-
-
-
-
690
800
-
-
-
6000
7000
-
-
-
nA
nA
pF
pF
pF
C
I
C
S(OFF)
C
S(ON)
input
capacitance
OFF-state
capacitance
ON-state
capacitance
NX3L1G3157
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 10 — 7 August 2012
5 of 22
京公网安备 11010802033920号
EEWORLD
