HIGH-SPEED CMOS 20-BIT LOW RESISTANCE, ACTIVE HIGH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH
®
PRODUCTS
IDTQS32XR862
HIGH-SPEED CMOS 20-BIT LOW
RESISTANCE, ACTIVE HIGH BUS SWITCH
WITH FLOW-THROUGH PINOUT
FEATURES:
−
−
−
−
−
−
Enhanced N channel FET with no inherent diode to Vcc
2.5Ω bidirectional switches connect inputs to outputs
Zero propagation delay, zero ground bounce
Undershoot clamp diodes on all switch and control pins
Active Low and High enable controls
Available in 48-pin QVSOP Package
DESCRIPTION:
The QS32XR862 provides two sets of ten high-speed CMOS, TTL-
compatible, active high, low resistance bus switches. The very low ON
resistance (2.5Ω) of the QS32XR862 allows inputs to be connected to
outputs without adding propagation delay and without generating additional
ground bounce noise. The switches are controlled by independent active
Low Enable (BE) and active High Enable (BE) controls for each set.
The QS32XR862 is ideal for switching digital buses as well as for hot plug
buffering and 5V to 3.3V conversion. The low ON resistance of the
QS32XR862 makes it ideal for PCI hot -docking applications.
The QS32XR862 is characterized for operation at -40°C to +85°C.
APPLICATIONS
−
−
−
−
−
−
−
Hot-swapping and hot-docking (low R
ON
resistance for PCI and
Compact PCI applications)
Voltage translation (5V to 3.3V)
Power conservation
Capacitance reduction and isolation
Applications requiring Low resistance and active High enabling
Bus isolation
Clock gating
FUNCTIONAL BLOCK DIAGRAM
A
0
B
0
A
9
B
9
BE
1
BE
1
A
10
B
10
A
19
B
19
BE
2
BE
2
INDUSTRIAL TEMPERATURE RANGE
1
c
1999 Integrated Device Technology, Inc.
NOVEMBER 1999
DSC-5540/-
IDTQS32XR862
HIGH-SPEED CMOS 20-BIT LOW RESISTANCE, ACTIVE HIGH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
(1)
Unit
V
V
V
V
mA
W
°C
PIN CONFIGURATION
BE
1
A
0
A
1
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
GND
BE
2
A
10
A
11
A
12
A
13
A
14
A
15
A
16
A
17
A
18
A
19
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
Vcc
BE
1
B
0
B
1
B
2
B
3
B
4
B
5
B
6
B
7
B
8
B
9
Vcc
BE
2
B
10
B
11
B
12
B
13
B
14
B
15
B
16
B
17
B
18
B
19
ABSOLUTE MAXIMUM RATINGS
Symbol
V
TERM(2)
V
TERM(3)
V
TERM(3)
V
AC
I
OUT
P
MAX
T
STG
Description
Supply Voltage to Ground
DC Switch Voltage V
S
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current
Maximum Power Dissipation
Storage Temperature
Max.
– 0.5 to +7
– 0.5 to +7
– 0.5 to +7
-3
120
.5
– 65 to +150
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these or
any other conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect reliability.
2. Vcc Terminals.
3. All terminals except Vcc.
CAPACITANCE
(T
A
= +25
O
C, f = 1.0MHz, V
IN
= 0V, V
OUT
= 0V)
Pins
Control Inputs
Quickswitch Channels (Switch OFF)
Typ.
3
5
Max.
(1)
4
6
Unit
pF
pF
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
BE
BE
A
0
- A
19
B
0
- B
19
I/O
I
I
I/O
I/O
Description
Active LOW Bus Enable
Active HIGH Bus Enable
Bus A
Bus B
FUNCTION TABLE
(1)
BE
1
L
L
H
H
BE
2
L
L
H
BE
1
L
H
L
H
BE
2
L
H
L
H
A
0
- A
9
Hi-Z
Hi-Z
B
0
- B
9
Hi-Z
A
10
- A
19
Hi-Z
Hi-Z
B
10
- B
19
Hi-Z
Disconnect
Disconnect
Connect
Disconnect
Disconnect
Disconnect
Connect
Disconnect
Function
Function
QVSOP
TOP VIEW
H
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedence
2
IDTQS32XR862
HIGH-SPEED CMOS 20-BIT LOW RESISTANCE, ACTIVE HIGH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= -40°C to +85°C, V
CC
= 5.0V ± 10%
Symbol
V
IH
V
IL
I
IN
I
OZ
R
ON
R
ON
V
P
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Switch ON Resistance
Switch ON Resistance
Pass Voltage
(2)
Test Conditions
Guaranteed Logic HIGH for Control Pins
Guaranteed Logic LOW for Control Pins
0V
≤
BEn,
BEn
≤
Vcc
0V
≤
V
OUT
≤
Vcc, Switches OFF
Vcc = Min., V
IN
= 0V, I
ON
= 30mA
Vcc = Min., V
IN
= 2.4V, I
ON
= 15mA
V
IN
= Vcc = 5V, I
OUT
= -5µA
Min.
2
—
—
—
—
—
3.7
Typ.
(1)
—
—
±0.01
±0.01
2.5
4
4
Max.
—
0.8
±1
±1
5
8.5
4.3
Unit
V
V
µA
µA
Ω
Ω
V
NOTES:
1. Typical values are at V
CC
= 5.0V, T
A
= 25°C.
2. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
R
ON
(ohms)
16
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
V
IN
(Volts)
3
IDTQS32XR862
HIGH-SPEED CMOS 20-BIT LOW RESISTANCE, ACTIVE HIGH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
∆I
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current per Control Input HIGH
(3)
Dynamic Power Supply Current per MHz
(4)
Test Conditions
(1)
V
CC
= Max., BEn = GND or Vcc, f = 0
V
CC
= Max., V
IN
= 3.4V, f = 0
V
CC
= Max., A and B pins open
Control Inputs Toggling at 50% Duty Cycle
Typ.
(2)
0.2
—
—
Max.
6
2.5
0.25
Unit
µA
mA
mA/MHz
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Typical values are at V
CC
= 5.0V, T
A
= 25°C.
3. Per TLL driven input (V
IN
= 3.4V, control inputs only). A and B pins do not contribute to
∆Icc.
4. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A
and B inputs generate no significant AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C, V
CC
= 5.0V ± 10%
C
LOAD
= 50pF, R
LOAD
= 500Ω unless otherwise noted.
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
Parameter
Data Propagation Delay
(2,3)
An to/from Bn
Switch Turn-on Delay
BEn
or BEn to An/Bn
Switch Turn-off Delay
(2)
BEn to An/Bn
Min.
(1)
—
1.5
1.5
Typ.
—
—
—
Max.
0.12
5.6
4.5
Unit
ns
ns
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time
constant for the switch alone is of the order of 0.12ns for C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical
driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the
driving circuit on the driving side of the switch and its interaction with the load on the driven side.
4
IDTQS32XR862
HIGH-SPEED CMOS 20-BIT LOW RESISTANCE, ACTIVE HIGH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
IDTQS
XXXXX
Device Type
XX
Package
X
Process
Blank
Industrial (-40°C to +85°C)
Q1
QVSOP
32XR862
High Speed CMOS 20-Bit Low Resistance, Active High
Bus Switch with Flow-Through Pinout
CORPORATE HEADQUARTERS
2975 Stender Way
Santa Clara, CA 95054
for SALES:
800-345-7015 or 408-727-6116
fax: 408-492-8674
www.idt.com*
*To search for sales office near you, please click the sales button found on our home page or dial the 800# above and press 2.
The IDT logo, QuickSwitch, and SynchroSwitch are registered trademarks of Integrated Device Technology, Inc.
[table=98%] [tr][td]Hello everyone: I use TMS570LS3137, set up the MASTER with Hercules, and then use several examples provided in Hercules, but I can't send data normally. The program always stops at...
The chip end sectors store some verification data. When using STVP to upgrade the software, the chip needs to be erased, and the verification data is also erased. Can STVP partially erase the sectors?...
Array LED display control system
After studying the last two articles on the LED display control system, many friends have asked me about the working principle and application of the array LED display...
Post a program to gain some popularityProgram Description:1: Hardware stm32f103, lmd18200 full bridge driver connected to pwm-tim3ch1, ch2 (pa6,7), dir-pa4, pa5, encoder output-tim4ch1, ch2 (pb8,9), s...
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
