CMOS SuperSync FIFO
™
16,384 x 9
32,768 x 9
FEATURES:
•
•
•
IDT72261LA
IDT72271LA
•
•
•
•
•
•
•
•
•
•
•
•
Choose among the following memory organizations:
IDT72261LA 16,384 x 9
•
IDT72271LA 32,768 x 9
Pin-compatible with the IDT72281/72291 SuperSync FIFOs
•
10ns read/write cycle time (8ns access time)
•
Fixed, low first word data latency time
Auto power down minimizes standby power consumption
DESCRIPTION:
Master Reset clears entire FIFO
Partial Reset clears data, but retains programmable
The IDT72261LA/72271LA are exceptionally deep, high speed, CMOS
settings
First-In-First-Out (FIFO) memories with clocked read and write controls.
Retransmit operation with fixed, low first word data
These FIFOs offer numerous improvements over previous SuperSync
latency time
FIFOs, including the following:
Empty, Full and Half-Full flags signal FIFO status
•
The limitation of the frequency of one clock input with respect to the other
has been removed. The Frequency Select pin (FS) has been removed,
Programmable Almost-Empty and Almost-Full flags, each flag
thus it is no longer necessary to select which of the two clock inputs,
can default to one of two preselected offsets
Program partial flags by either serial or parallel means
RCLK or WCLK, is running at the higher frequency.
Select IDT Standard timing (using EF and FF flags) or First Word
•
The period required by the retransmit operation is now fixed and short.
Fall Through timing (using OR and IR flags)
•
The first word data latency period, from the time the first word is written
Output enable puts data outputs into high impedance state
to an empty FIFO to the time it can be read, is now fixed and short. (The
Easily expandable in depth and width
Independent Read and Write clocks (permit reading and writing
simultaneously)
Available in the 64-pin Thin Quad Flat Pack (TQFP) and the 64-
pin Slim Thin Quad Flat Pack (STQFP)
High-performance submicron CMOS technology
Industrial temperature range (–40°C to +85°C) is available
FUNCTIONAL BLOCK DIAGRAM
WEN
WCLK
D
0
-D
8
LD SEN
INPUT REGISTER
OFFSET REGISTER
FF/IR
PAF
EF/OR
PAE
HF
FWFT/SI
WRITE CONTROL
LOGIC
RAM ARRAY
16,384 x 9
32,768 x 9
FLAG
LOGIC
WRITE POINTER
READ POINTER
READ
CONTROL
LOGIC
OUTPUT REGISTER
MRS
PRS
RT
RESET
LOGIC
RCLK
REN
OE
Q
0
-Q
8
4671 drw 01
The IDT logo is a registered trademark and the SuperSyncFIFO is a trademark of Integrated Device Technology, Inc.
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGE
1
c 2001 Integrated Device Technology
APRIL 2001
DSC-4671/1
IDT72261LA/72271LA SuperSync FIFO™
16,384 x 9, 32,768 x 9
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGE
DESCRIPTION (CONTINUED)
variable clock cycle counting delay associated with the latency period
found on previous SuperSync devices has been eliminated on this
SuperSync family.)
SuperSync FIFOs are particularly appropriate for network, video, tele-
communications, data communications and other applications that need
to buffer large amounts of data.
The input port is controlled by a Write Clock (WCLK) input and a Write
Enable (WEN) input. Data is written into the FIFO on every rising edge of
WCLK when
WEN
is asserted. The output port is controlled by a Read
Clock (RCLK) input and Read Enable (REN) input. Data is read from the
FIFO on every rising edge of RCLK when
REN
is asserted. An Output
Enable (OE) input is provided for three-state control of the outputs.
The frequencies of both the RCLK and the WCLK signals may vary from
0 to fMAX with complete independence. There are no restrictions on the
frequency of one clock input with respect to the other.
There are two possible timing modes of operation with these devices:
IDT Standard mode and First Word Fall Through (FWFT) mode.
In
IDT Standard mode,
the first word written to an empty FIFO will not
appear on the data output lines unless a specific read operation is
PIN CONFIGURATIONS
LD
FWFT/SI
GND
WCLK
PRS
EF/OR
RCLK
REN
RT
OE
FF/IR
PAF
HF
MRS
V
CC
PAE
PIN 1
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
WEN
SEN
DC
(1)
V
CC
V
CC
GND
(2)
GND
(2)
GND
(2)
GND
(2)
GND
(2)
GND
(2)
GND
(2)
GND
(2)
GND
(2)
D8
D7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
DNC
(3)
DNC
(3)
GND
DNC
(3)
DNC
(3)
V
CC
DNC
(3)
DNC
(3)
DNC
(3)
GND
DNC
(3)
DNC
(3)
Q8
Q7
Q6
GND
GND
Q0
Q1
GND
Q2
D5
D4
D3
D2
D1
D0
TQFP (PN64-1, ORDER CODE: PF)
STQFP (PP64-1, ORDER CODE: TF)
TOP VIEW
NOTES:
1. DC = Don’t Care. Must be tied to GND or V
CC
, cannot be left open.
2. This pin may either be tied to ground or left open.
3. DNC = Do Not Connect.
2
Q3
V
CC
Q4
Q5
D6
4671 drw 02
IDT72261LA/72271LA SuperSync FIFO™
16,384 x 9, 32,768 x 9
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGE
DESCRIPTION (CONTINUED)
performed. A read operation, which consists of activating REN and
enabling a rising RCLK edge, will shift the word from internal memory to the
data output lines.
In
FWFT mode,
the first word written to an empty FIFO is clocked directly
to the data output lines after three transitions of the RCLK signal. A
REN
does not have to be asserted for accessing the first word. However,
subsequent words written to the FIFO do require a LOW on
REN
for
access. The state of the FWFT/SI input during Master Reset determines
the timing mode in use.
For applications requiring more data storage capacity than a single
FIFO can provide, the FWFT timing mode permits depth expansion by
chaining FIFOs in series (i.e. the data outputs of one FIFO are connected
to the corresponding data inputs of the next). No external logic is required.
These FIFOs have five flag pins,
EF/OR
(Empty Flag or Output Ready),
FF/IR
(Full Flag or Input Ready),
HF
(Half-full Flag),
PAE
(Programmable
Almost-Empty flag) and
PAF
(Programmable Almost-Full flag). The
EF
and
FF
functions are selected in IDT Standard mode. The
IR
and
OR
functions are selected in FWFT mode.
HF, PAE
and
PAF
are always
available for use, irrespective of timing mode.
PAE
and
PAF
can be programmed independently to switch at any point
in memory. (See Table I and Table II.) Programmable offsets determine
the flag switching threshold and can be loaded by two methods: parallel or
serial. Two default offset settings are also provided, so that
PAE
can be
set to switch at 127 or 1,023 locations from the empty boundary and the
PAF
threshold can be set at 127 or 1,023 locations from the full boundary.
These choices are made with the LD pin during Master Reset.
For serial programming,
SEN
together with
LD
on each rising edge of
WCLK, are used to load the offset registers via the Serial Input (SI). For
parallel programming,
WEN
together with
LD
on each rising edge of
WCLK, are used to load the offset registers via Dn.
REN
together with
LD
on each rising edge of RCLK can be used to read the offsets in parallel from
Qn regardless of whether serial or parallel offset loading has been
selected.
During Master Reset (MRS) the following events occur: The read and
write pointers are set to the first location of the FIFO. The FWFT pin selects
IDT Standard mode or FWFT mode. The
LD
pin selects either a partial flag
default setting of 127 with parallel programming or a partial flag default
setting of 1,023 with serial programming. The flags are updated according
to the timing mode and default offsets selected.
The Partial Reset (PRS) also sets the read and write pointers to the first
location of the memory. However, the timing mode, partial flag program-
ming method, and default or programmed offset settings existing before
Partial Reset remain unchanged. The flags are updated according to the
timing mode and offsets in effect.
PRS
is useful for resetting a device in
mid-operation, when reprogramming partial flags would be undesirable.
The Retransmit function allows data to be reread from the FIFO more
than once. A LOW on the
RT
input during a rising RCLK edge initiates a
retransmit operation by setting the read pointer to the first location of the
memory array.
If, at any time, the FIFO is not actively performing an operation, the chip
will automatically power down. Once in the power down state, the standby
supply current consumption is minimized. Initiating any operation (by
activating control inputs) will immediately take the device out of the power
down state.
The IDT72261LA/72271LA are fabricated using IDT’s high speed sub-
micron CMOS technology.
PARTIAL RESET (PRS)
WRITE CLOCK (WCLK)
WRITE ENABLE (WEN)
LOAD (LD)
DATA IN (D
0
- D
n
)
SERIAL ENABLE(SEN)
FIRST WORD FALL THROUGH/SERIAL INPUT
(FWFT/SI)
FULL FLAG/INPUT READY (FF/IR)
PROGRAMMABLE ALMOST-FULL (PAF)
MASTER RESET (MRS)
READ CLOCK (RCLK)
READ ENABLE (REN)
OUTPUT ENABLE (OE)
DATA OUT (Q
0
- Q
n
)
IDT
72261LA
72271LA
RETRANSMIT (RT)
EMPTY FLAG/OUTPUT READY (EF/OR)
PROGRAMMABLE ALMOST-EMPTY (PAE)
HALF FULL FLAG (HF)
4671 drw 03
Figure 1. Block Diagram of Single 16,384 x 9 and 32,768 x 9 Synchronous FIFO
3
IDT72261LA/72271LA SuperSync FIFO™
16,384 x 9, 32,768 x 9
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGE
PIN DESCRIPTION
Symbol
D
0
–D
8
MRS
Name
Data Inputs
Master Reset
I/O
I
I
Data inputs for a 9-bit bus.
MRS
initializes the read and write pointers to zero and sets the output register to all zeroes.
During Master Reset, the FIFO is configured for either FWFT or IDT Standard mode, one of
two programmable flag default settings, and serial or parallel programming of the offset settings.
PRS
initializes the read and write pointers to zero and sets the output method (serial or parallel),
and programmable flag settings are all retained.
RT
asserted on the rising edge of RCLK initializes the READ pointer to zero, sets the
EF
flag to
LOW (OR to HIGH in FWFT mode) temporarily and does not disturb the write pointer, programming
method, existing timing mode or programmable flag settings.
RT
is useful to reread data from the
first physical location of the FIFO.
During Master Reset, selects First Word Fall Through or IDT Standard mode. Through/Serial
In After Master Reset, this pin functions as a serial input for loading offset registers
When enabled by
WEN,
the rising edge of WCLK writes data into the FIFO and offsets into
the programmable registers for parallel programming, and when enabled by
SEN,
the rising
edge of WCLK writes one bit of data into the programmable register for serial programming.
WEN
enables WCLK for writing data into the FIFO memory and offset registers.
When enabled by
REN,
the rising edge of RCLK reads data from the FIFO memory and offsets
from the programmable registers.
REN
enables RCLK for reading data from the FIFO memory and offset registers.
OE
controls the output impedance of Q
n.
SEN
enables serial loading of programmable flag offsets.
During Master Reset,
LD
selects one of two partial flag default offsets (127 or 1,023) and
determines the flag offset programming method, serial or parallel. After Master Reset, this pin
enables writing to and reading from the offset registers.
This pin must be tied to either V
CC
or GND and must not toggle after Master Reset.
In the IDT Standard mode, the
FF
function is selected.
FF
indicates whether or not the FIFO
memory is full. In the FWFT mode, the
IR
function is selected.
IR
indicates whether or not there
is space available for writing to the FIFO memory.
In the IDT Standard mode, the
EF
function is selected.
EF
indicates whether or not the FIFO
memory is empty. In FWFT mode, the
OR
function is selected. OR indicates whether or not
there is valid data available at the outputs.
PAF
goes LOW if the number of words in the FIFO memory is more than word capacity of the
FIFO minus the full offset value m, which is stored in the Full Offset register. There are two
possible default values for m: 127 or 1,023.
PAE
goes LOW if the number of words in the FIFO memory is less than offset n, which is stored
in the Empty Offset register. There are two possible default values for n: 127 or 1,023. Other
values for n can be programmed into the device.
HF
indicates whether the FIFO memory is more or less than half-full.
Data outputs for a 9-bus
+5 Volt power supply pins.
Ground pins.
Description
PRS
RT
Partial Reset
Retransmit
I
I
FWFT/SI
WCLK
First Word Fall
Write Clock
I
I
WEN
RCLK
REN
OE
SEN
LD
Write Enable
Read Clock
Read Enable
Output Enable
Serial Enable
Load
I
I
I
I
I
I
DC
FF/IR
Don't Care
Full Flag/
Input Ready
Empty Flag/
Output Ready
Programmable
Almost-Full Flag
Programmable
Almost-Empty Flag
Half-Full Flag
Data Outputs
Power
Ground
I
O
EF/OR
O
PAF
O
PAE
O
HF
Q
0
–Q
8
V
CC
GND
O
O
4
IDT72261LA/72271LA SuperSync FIFO™
16,384 x 9, 32,768 x 9
COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS
Symbol
V
TERM
T
STG
I
OUT
Rating
Terminal Voltage
with respect to GND
Storage
Temperature
DC Output Current
Com’l & Ind’l
–0.5 to +7
–55 to +125
–50 to +50
Unit
V
°C
mA
RECOMMENDED DC OPERATING
CONDITIONS
Symbol
VCC
GND
VIH
Parameter
Supply Voltage
Commercial/Industrial
Supply Voltage
Input High Voltage
Commercial/Industrial
Input Low Voltage
Commercial/Industrial
Operating Temperature
Commercial
Operating Temperature
Industrial
0
2.0
—
0
–40
0
—
—
—
—
0
—
0.8
70
85
V
V
V
°C
°C
Min.
4.5
Typ.
5.0
Max.
5.5
Unit
V
NOTE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
VIL
(1)
TA
TA
NOTE:
1.5V undershoots are allowed for 10ns once per cycle.
DC ELECTRICAL CHARACTERISTICS
(Commercial: VCC = 5V ± 10%, TA = 0°C to +70°C; Industrial: VCC = 5V ± 10%, TA = –40°C to +85°C)
IDT72261LA
IDT72271LA
Commercial and Industrial
(1)
t
CLK
= 10, 15, 20 ns
Symbol
I
LI
(2)
I
LO
(3)
V
OH
V
OL
I
CC1
(4,5,6)
I
CC2
(4,7)
Input Leakage Current
Output Leakage Current
Output Logic “1” Voltage, I
OH
= –2 mA
Output Logic “0” Voltage, I
OL
= 8 mA
Active Power Supply Current
Standby Current
Parameter
Min.
–1
–10
2.4
—
—
—
Max.
1
10
—
0.4
75
20
Unit
µA
µA
V
V
mA
mA
NOTES:
1. Industrial temperature range product for the 15ns and 20ns speed grade are available as a standard device.
2. Measurements with 0.4
≤
V
IN
≤
V
CC
.
3.
OE
≥
V
IH
, 0.4
≤
V
OUT
≤
V
CC
.
4. Tested with outputs disabled (I
OUT
= 0).
5. RCLK and WCLK toggle at 20 MHz and data inputs switch at 10 MHz.
6. Typical I
CC1
= 15 + 1.85*fS + 0.02*C
L
*f
S
(in mA) with V
CC
= 5V, t
A
= 25°C, f
S
= WCLK frequency = RCLK frequency (in MHz, using TTL levels), data switching at f
S
/2,
C
L
= capacitive load (in pF).
7. All Inputs = V
CC
- 0.2V or GND + 0.2V, except RCLK and WCLK, which toggle at 20 MHz.
CAPACITANCE
(T
A
= +25°C, f = 1.0MHz)
Symbol
C
IN
(2)
C
OUT
(1,2)
Parameter
(1)
Input
Capacitance
Output
Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Max.
10
10
Unit
pF
pF
NOTES:
1. With output deselected, (OE
≥
VIH).
2. Characterized values, not currently tested.
5
京公网安备 11010802033920号
EEWORLD
