Enhanced N channel FET with no inherent diode to Vcc
5Ω bidirectional switches connect inputs to outputs
Ω
Zero propagation delay, zero added ground bounce
Undershoot clamp diodes on all switch and control inputs
Bus exchange allows nibble swap
Available in QSOP package
APPLICATIONS:
•
•
•
•
The QS3383 provides ten high-speed CMOS TTL-compatible bus
switches. The low ON resistance of the QS3383 allows inputs to be
connected to outputs without adding propagation delay and without gener-
ating additional ground bounce noise. The Bus Enable (BE) signal turns
the switches on. The Bus Exchange (BX) signal provides nibble swap of
the AB and CD pairs of signals. This exchange configuration allows byte
swapping of buses in systems. It can also be used as a 5-wide 2-to-1
multiplexer and to create low delay barrel shifters, etc.
The QS3383 is characterized for operation at -40°C to +85°C.
Hot-swapping, hot-docking
Voltage translation (5V to 3.3V)
Resource sharing
Crossbar switching
FUNCTIONAL BLOCK DIAGRAM
A0
C0
B0
D0
A4
C4
B4
D4
BX
BE
INDUSTRIAL TEMPERATURE RANGE
c 2011 Integrated Device Technology, Inc.
OCTOBER 2011
1
DSC-5571/5
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
BE
C0
A0
B0
D0
C1
A1
B1
D1
C2
A2
GND
1
2
3
4
5
6
7
8
9
10
11
12
QSOP
TOP VIEW
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Supply Voltage to Ground
DC Switch Voltage V
S
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current
Maximum Power Dissipation (T
A
= 85°C)
Storage Temperature
Max
–0.5 to +7
–0.5 to +7
–0.5 to +7
–3
120
0.5
–65 to +150
Unit
V
V
V
V
mA
W
°C
24
23
22
21
20
19
18
17
16
15
14
13
V
CC
D4
B4
A4
C4
D3
B3
A3
C3
D2
B2
BX
V
TERM
(2)
V
TERM
(3)
V
TERM
(3)
V
AC
I
OUT
P
MAX
T
STG
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
CAPACITANCE
(T
A
= +25°C, f = 1MHz, V
IN
= 0V, V
OUT
= 0V)
Pins
Control Inputs
Quickswitch Channels (Switch OFF)
Typ.
3
5
Max.
(1)
5
7
Unit
pF
pF
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
A
0
- A
4
, B
0
- B
4
C
0
- C
4
, D
0
- D
4
BE
BX
I/O
I/O
I/O
I
I
Description
A and B Buses
C and D Buses
Bus Switch Enable
Bus Exchange
FUNCTION TABLE
(1)
BE
H
L
L
BX
X
L
H
A
0
- A
4
Hi-Z
C
0
- C
4
D
0
- D
4
B
0
- B
4
Hi-Z
D
0
- D
4
C
0
- C
4
Function
Disconnect
Connect
Exchange
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
Z = High-Impedance
2
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 5V ± 5%
Symbol
V
IH
V
IL
I
IN
I
OZ
R
ON
V
P
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Switch ON Resistance
(2)
Pass Voltage
(3)
Test Conditions
Guaranteed Logic HIGH for Control Pins
Guaranteed Logic LOW for Control Pins
0V
≤
V
IN
≤
V
CC
0V
≤
V
OUT
≤
V
CC
, Switches OFF
V
CC
= Min., V
IN
= 0V, I
ON
= 30mA
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
V
IN
= V
CC
= 5V, I
OUT
= -5μA
Min.
2
—
—
—
—
—
3.7
Typ.
(1)
Max.
—
—
0.01
0.01
6
12
4
—
0.8
±1
±1
8
17
4.2
V
Unit
V
V
μA
μA
Ω
NOTES:
1. Typical values are at V
CC
= 5V and T
A
= 25°C.
2. R
ON
is guaranteed but not production tested.
3. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
16
14
R
ON
(ohms)
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
V
IN
(Volts)
2.0
2.5
3.0
3.5
3
IDTQS3383
HIGH-SPEED CMOS 10-BIT BUS EXCHANGE SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
ΔI
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current per Input HIGH
(2)
Dynamic Power Supply Current per MHz
(3)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3.4V, f = 0
V
CC
= Max., A and B Pins Open, Control Inputs Toggling @ 50% Duty Cycle
Max.
1.5
2.5
0.25
Unit
mA
mA
mA/MHz
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TTL-driven input (V
IN
= 3.4V, control inputs only). A, B,C, and D pins do not contribute to
ΔIcc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C, V
CC
= 5V ± 5%
C
LOAD
= 50pF, R
LOAD
= 500Ω unless otherwise noted.
Symbol
t
PLH
t
PHL
t
PZL
t
PZH
t
PLZ
t
PHZ
t
BX
Parameter
Data Propagation Delay
(2)
AxBx to CxDx, CxDx to AxBx
Switch Turn-On Delay
BE
to Ax, Bx, Cx, Dx
Switch Turn-Off Delay
(2)
BE
to Ax, Bx, Cx, Dx
Switch Multiplex Delay
BX to Ax, Bx, Cx, Dx
1.5
⎯
6.5
ns
Min
.
(1)
⎯
1.5
1.5
Typ.
⎯
⎯
⎯
Max.
0.25
(3)
6.5
5.5
Unit
ns
ns
ns
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.25ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
Does anyone know how Ad-hoc self-organizes a network, how to discover the surrounding networks and connect to them? ? ? ? I would be very grateful! ! ! !...
In recent years , PDA , DSC , Cellular Phone , Camcorder , Portable Audio , Advanced Game , Assist Bicycle , Electric Scooter , Bluetooth Device ...More and more products are rapidly using lithium bat...
I tried the following methods: 1. [code]int mciSendString(CString lpstrCommand, CString lpstrRetumString, int uReturnLength, int hwndCallback); mciSendString("close OpenFile", "", 0, 0); mciSendString...
I would like to ask about a switch circuit: There are two DC power supplies, a red light, a green light, and a fan. (One power supply powers the light, and the other power supply powers the fan) The f...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
Sailing is gaining more and more attention. How to use modern technology to assist training and improve competition results is particularly important. Considering the real-time data collection in t...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
LED guardrail lights use fluorescent tubes or LEDs as light sources and continuous guardrails as carriers to form an approximately linear guardrail light strip. This article mainly introduces...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
Mobile phones, MP3s, tablet computers, laptops, digital cameras, handheld game consoles, navigation devices, etc., all these mobile devices are powered by mobile batteries, and the battery life is ...[Details]
1 Introduction
Fieldbus is a serial, digital, multi-point communication data bus between field equipment/instruments installed in the production process area and automatic control devices/syst...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
Today, fleet management innovation has made great progress. Whether trucks, buses, taxis or other means of transportation, wireless satellite positioning systems are used to enable dispatchers to u...[Details]
"Multimeter" is the abbreviation of multimeter, which is an indispensable tool in our electronic production. The advantages of multimeter are that it has many uses, a wide range, an...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
