EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-63149F4-500K

Description
Line Driver/Receiver, 2 Driver, Hybrid, CDFP36
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size65KB,8 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-63149F4-500K Overview

Line Driver/Receiver, 2 Driver, Hybrid, CDFP36

BU-63149F4-500K Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
MakerData Device Corporation
Reach Compliance Codecompliant
ECCN codeEAR99
Differential outputYES
Number of drives2
High level input current maximum value0.0001 A
JESD-30 codeR-XDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Minimum output swing18 V
Maximum output low current0.0034 A
Package body materialCERAMIC
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
power supply5 V
Certification statusNot Qualified
Maximum receive delay
Maximum slew rate565 mA
Nominal supply voltage5 V
surface mountYES
technologyHYBRID
Temperature levelINDUSTRIAL
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
Base Number Matches1
BU-63147 and BU-63149
MIL-STD-1553 DATA BUS
+5V TRANSCEIVER
DESCRIPTION
The BU-63147/49 transceiver is a com-
plete dual transmitter and receiver pair
conforming fully to MIL-STD-1553A
and 1553B. Features include: mono-
lithic design, +5V power supply voltage,
Harris or Smiths type decoder inter-
face, completely independent dual
redundant operation, and small size
(36 pin DIP). The receiver section of
the BU-63147/49 series accepts
phase-modulated bipolar data from a
MIL-STD-1553 Data Bus and pro-
duces TTL Signal data at its output.
RX DATA OUT and
RX DATA OUT
These outputs represent positive and
negative variations of the input data
signals beyond an internally fixed
threshold level. An external STROBE
input enables or disables the receiver’s
outputs.
The transmitter section accepts
bi-phase TTL signal data at its
TX DATA IN and
TX DATA IN
inputs
and produces phase-modulated
bipolar data at the TX DATA OUT and
TX DATA OUT
outputs.
The
transmitter’s output voltage level is
typically about 11Vpp. An external
input, INHIBIT, takes priority over the
transmitter inputs and disables the
transmitter when activated with a logic
“1”.
The small size, +5V power supply volt-
age,
and
compliance
with
MIL-STD-1553 simplify engineering
design, making it an excellent choice
for interfacing with any MIL-STD-1553
system.
FEATURES
+5V Power Supply
Low Power
Conforms Fully To MIL-STD-1553A
AND 1553B
Dual Transceiver
Available with MIL-STD-1760
Compliant Transmitter Voltage
Available with McAir Compatible
Waveform
36-Pin DIP
HARRIS or SMITHS I/O
Compatibility
+5 V
1553
DATA
BUS
RECEIVER STROBE
BI PHASE
TTL DATA
COMPARATOR
RX DATA OUT
RX DATA OUT
DECODER
PHASE MODULATED
BIPOLAR DATA
RX DATA IN
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX DATA IN
RECEIVER SECTION
FILTER
FILTER
COMPARATOR
TRANSMITTER SECTION
TX Data Out
SHAPING
NETWORK
TX DATA IN
TX Data Out
SHAPING
NETWORK
ENCODER
TX DATA IN
CASE/GND
TX INHIBIT
FIGURE 1. BU-63147/49 BLOCK DIAGRAM
(one
channel shown)
©
2000
Data Device Corporation
Strange problems encountered when stm32 controls the camera ov7670
[i=s]This post was last edited by paulhyde on 2014-9-15 04:06[/i] I am using STM32F103ZE, the camera is ov7670 with FIFO, the display is ILI9320 (320×240), the interrupt program is as follows: void EX...
ET6V Electronics Design Contest
Power supply product aging standards and references
For power supply products, especially for newly developed and put into production switching power supply products, in addition to conventional electrical performance tests, it is also necessary to sim...
qwqwqw2088 Analogue and Mixed Signal
Is the IoT card a data card? What is the difference between it and a mobile phone data card?
Simply put, the Internet of Things card is a mobile communication access service provided by operators to Internet of Things users. Internet of Things users realize the interaction between things and ...
迈卡德科技 Industrial Control Electronics
About the problem of cross-compiling strongswan for mipsel-linux
I encountered a problem when cross-compiling strongswan. I searched for a long time on the Internet but couldn't find a definite answer. The problem is as follows: mipsel-linux-ld: ../../../lib/libcry...
lixs688 Linux and Android
About enet-lwip
May I ask: pucMACArray[0] = ((ulUser0 >> 0) & 0xff); pucMACArray[1] = ((ulUser0 >> 8) & 0xff); pucMACArray[2] = ((ulUser0 >> 16) & 0xff); pucMACArray[3] = ((ulUser1 >> 0) & 0xff); pucMACArray[4] = ((u...
lvfeihi Microcontroller MCU
Determine whether there is a memory card or a built-in memory card on the PDA
Using vc2005, ppc2003, how can I tell if there is a memory card or a built-in memory card on the pda and read out the name?...
qz410152 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1154  2054  2785  818  385  24  42  57  17  8 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号