REVISIONS
LTR
A
DESCRIPTION
Added device type 04. Technical changes were implemented. Editorial
changes throughout.
Added device types 05, 06, and 07. Technical changes to table I. Editorial
changes throughout.
Changes in accordance with NOR 5962-R063-99.
Update boilerplate to MIL-PRF-38535 requirements. - CFS
Correct dimensioning on case outlines T, U, and X. - CFS
DATE (YR-MO-DA)
92-05-06
APPROVED
Monica L. Poelking
B
94-03-03
Monica L. Poelking
C
D
E
99-05-27
05-10-03
05-11-01
Monica L. Poelking
Thomas M. Hess
Thomas M. Hess
REV
SHEET
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
D
55
D
35
E
15
D
56
D
36
E
16
D
37
D
17
D
38
D
18
REV
SHEET
PREPARED BY
Todd D. Creek
D
39
D
19
D
40
D
20
D
41
D
21
E
1
D
42
D
22
D
2
D
43
D
23
D
3
D
44
D
24
D
4
D
45
D
25
D
5
D
46
D
26
D
6
D
47
D
27
D
7
D
48
D
28
D
8
D
49
D
29
D
9
D
50
D
30
D
10
D
51
D
31
D
11
D
52
D
32
D
12
D
53
D
33
D
13
D
54
D
34
E
14
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
CHECKED BY
Ray Monnin
APPROVED BY
Michael A. Frye
DRAWING APPROVAL DATE
89-03-01
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
MICROCIRCUIT, DIGITAL, CMOS, 16-BIT,
MIL-STD-1750 MICROPROCESSOR
MONOLITHIC SILICON
AMSC N/A
REVISION LEVEL
E
SIZE
A
SHEET
CAGE CODE
67268
1 OF
56
5962-87665
DSCC FORM 2233
APR 97
5962-E037-06
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87665
01
X
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type
01
02
03
04
05
06
07
Generic number
P1750A-15
P1750A-20
P1750A-30
P1750A-40
P1750AE-20
P1750AE-30
P1750AE-40
Circuit function
16-bit microprocessor
16-bit microprocessor
16-bit microprocessor
16-bit microprocessor
16-bit microprocessor
16-bit microprocessor
16-bit microprocessor
Speed
15 MHz
20 MHz
30 MHz
40 MHz
20 MHz
30 MHz
40 MHz
1.2.2 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
T
U
X
Y
Z
Descriptive designator
See figure 1.
See figure 1.
See figure 1.
See figure 1.
See figure 1.
Terminals
64
68
64
68
68
Package style
Dual-in-line with gull-wing leads
Leaded chip carrier with unformed leads
Dual-in-line
Leaded chip carrier with gull-wing leads
Pin grid array
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87665
SHEET
D
2
1.3 Absolute maximum ratings.
Supply voltage range (V
CC
) ........................................................................................ -0.5 V dc to +7.0 V dc
Input voltage range .................................................................................................... -0.5 V dc to V
CC
+ 0.5 V dc
Storage temperature range ........................................................................................ -65°C to +150°C
Input current range..................................................................................................... -30 mA to +5 mA
Voltage applied to inputs range.................................................................................. -0.5 V dc to V
CC
+ 0.5 V dc
Current applied to any output ..................................................................................... 100 mA
Maximum power dissipation (P
D
)................................................................................ 1.5 W 1/
Lead temperature range (soldering, 10 seconds)....................................................... +300°C
Thermal resistance, junction-to-case (θ
JC
):
Cases T and X........................................................................................................ 8°C/W
Cases U and Y ....................................................................................................... 5°C/W
Case Z .................................................................................................................... 6°C/W
1.4 Recommended operating conditions.
Supply voltage range.................................................................................................. 4.5 V dc to 5.5 V dc
Case operating temperature range (T
C
) ..................................................................... -55°C to +125°C
Operating worst case power dissipation (outputs open):
Device type 01........................................................................................................ 0.25 W at 15 MHz
Device type 02........................................................................................................ 0.30 W at 20 MHz
Device type 03........................................................................................................ 0.35 W at 30 MHz
Device type 04........................................................................................................ 0.40 W at 40 MHz
Device type 05........................................................................................................ 0.40 W at 20 MHz
Device type 06........................................................................................................ 0.50 W at 30 MHz
Device type 07........................................................................................................ 0.60 W at 40 MHz
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535
-
Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883
MIL-STD-1835
-
-
Test Method Standard Microcircuits.
Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103
MIL-HDBK-780
-
-
List of Standard Microcircuit Drawings.
Standard Microcircuit Drawings.
(Copies of these documents are available online at
http://assist.daps.dla.mil/quicksearch/
or
http://assist.daps.dla.mil
or from
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
________
1/ Must withstand the added P
D
due to short circuit test; e.g., I
OS
.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87665
SHEET
D
3
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein and as specified on figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Functional block diagram. The functional block diagram shall be as specified on figure 3.
3.2.4 Timing waveforms and test circuits. The timing waveforms and test circuits shall be as specified on figure 4.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full case operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
3.10 Certification. Certification to MIL-STD-1750A VSW test version 2.2 shall be required and the manufacturer shall be
listed on Air Force VSW Compliant Computer List.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87665
SHEET
D
4
TABLE I. Electrical performance characteristics.
Conditions
Test
Symbol
4.5 V
≤
V
CC
≤
5.5 V
-55°C
≤
T
C
≤
+125°C
unless otherwise specified
Group A
subgroups
Device
type
Min
Input high level voltage
Input low level voltage
Input clamp diode voltage
High level output voltage
V
IH
V
IL
V
CD
V
OH
V
CC
= 4.5 V, I
IN
= -18 mA
I
OH
= -8.0 mA, V
CC
= 4.5 V
I
OH
= -300
µA,
V
CC
= 4.5 V
Low level output voltage
High level input current,
except IB
0
- IB
15
,
BUS BUSY, BUS LOCK
High level input current,
IB
0
- IB
15
, BUS BUSY,
BUS LOCK
Low level input current,
except IB
0
- IB
15
,
BUS BUSY, BUS LOCK
Low level input current,
IB
0
- IB
15
, parity/IB
16
,
BUS BUSY, BUS LOCK
Output three-state current
Output three-state current
Quiescent power supply
current (CMOS input
levels)
Quiescent power supply
current (TTL input
levels)
Dynamic power supply
current
V
OL
I
IH1
I
OL
= 8.0 mA, V
CC
= 4.5 V
I
OL
= 300
µA,
V
CC
= 4.5 V
V
IN
= V
CC
, V
CC
= 5.5 V
1, 2, 3
All
1, 2, 3
All
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
All
All
All
All
2.4
V
CC
–
0.2
0.5
0.2
10
µA
V
2.0
-0.5
Limits
Unit
Max
V
CC
+
0.5
0.8
-1.2
V
V
V
V
I
IH2
V
IN
= V
CC
, V
CC
= 5.5 V
1, 2, 3
All
50
µA
I
IL1
V
IN
= GND, V
CC
= 5.5 V
1, 2, 3
All
-10
µA
I
IL2
V
IN
= GND, V
CC
= 5.5 V
1, 2, 3
All
-50
µA
I
OZH
I
OZL
I
CCQC
V
OUT
= 2.4 V, V
CC
= 5.5 V
V
OUT
= 0.5 V, V
CC
= 5.5 V
V
IN
<
0.2 V or V
IN
>
V
CC
– 0.2 V,
f = 0 MHz, outputs open,
V
CC
= 5.5 V
V
IN
= 3.4 V, f = 0 MHz,
outputs open, V
CC
= 5.5 V
V
IN
= 0 V to V
CC
,
t
r
= t
f
= 2.5 ns nominal,
outputs open, V
CC
= 5.5 V
1, 2, 3
1, 2, 3
1, 2, 3
All
All
01, 02,
03, 04
05, 06,
07
50
-50
10
20
50
µA
µA
mA
I
CCQT
1, 2, 3
All
mA
I
CCD
1, 2, 3
01
02
03
04
05
06
07
40
50
60
70
70
85
100
mA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
5962-87665
SHEET
D
5
京公网安备 11010802033920号
EEWORLD
