without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. 00F
05/26/05
1
IS93C76A
IS93C86A
ISSI
8-Pin JEDEC SOIC “GR”
®
PIN CONFIGURATIONS
8-Pin DIP, 8-Pin TSSOP
CS
SK
D
IN
D
OUT
1
2
3
4
8
7
6
5
VCC
NC
ORG
GND
CS
SK
D
IN
D
OUT
1
2
3
4
8
7
6
5
VCC
NC
ORG
GND
PIN DESCRIPTIONS
CS
SK
D
IN
D
OUT
ORG
NC
Vcc
GND
Chip Select
Serial Data Clock
Serial Data Input
Serial Data Output
Organization Select
Not Connected
Power
Ground
instruction begins with a start bit of the logical “1” or
HIGH. Following this are the opcode (2 bits),
address field (10 or 11 bits), and data, if appropriate.
The clock signal may be held stable at any moment to
suspend the device at its last state, allowing clock-
speed flexibility. Upon completion of bus
communication, CS would be pulled LOW. The device
then would enter Standby mode if no internal
programming is underway.
Read (READ)
The READ instruction is the only instruction that outputs
serial data on the D
OUT
pin. After the read instruction and
address have been decoded, data is transferred from the
selected memory register into a serial shift register. (Please
note that one logical “0” bit precedes the actual 8 or 16-bit
output data string.) The output on D
OUT
changes during the
low-to-high transitions of SK (see Figure 3).
Applications
The IS93C76A/86A are very popular in many
applications which require low-power, low-density
storage. Applications using these devices include
industrial controls, networking, and numerous other
consumer electronics.
Low Voltage Read
The IS93C76A/86A are designed to ensure that data read
operations are reliable in low voltage environments. They
provide accurate operation with Vcc as low as 1.8V.
Endurance and Data Retention
The IS93C76A/86A are designed for applications requiring
up to 1M programming cycles (WRITE, WRALL, ERASE
and ERAL). They provide 40 years of secure data retention
without power after the execution of 1M programming cycles.
Auto Increment Read Operations
In the interest of memory transfer operation applications,
the IS93C76A/86A are designed to output a continuous
stream of memory content in response to a single read
operation instruction. To utilize this function, the system
asserts a read instruction specifying a start location ad-
dress. Once the 8 or 16 bits of the addressed register have
been clocked out, the data in consecutively higher address
locations is output. The address will wrap around continu-
ously with CS HIGH until the chip select (CS) control pin is
brought LOW. This allows for single instruction data dumps
to be executed with a minimum of firmware overhead.
Device Operations
The IS93C76A/86A are controlled by a set of
instructions which are clocked-in serially on the Din pin.
Before each low-to-high transition of the clock (SK), the
CS pin must have already been raised to HIGH, and the
Din value must be stable at either LOW or HIGH. Each
2
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. 00F
05/26/05
IS93C76A
IS93C86A
ISSI
Write All (WRALL)
®
Write Enable (WEN)
The write enable (WEN) instruction must be executed
before any device programming (WRITE, WRALL,
ERASE, and ERAL) can be done. When Vcc is applied,
this device powers up in the write disabled state. The
device then remains in a write disabled state until a WEN
instruction is executed. Thereafter, the device remains
enabled until a WDS instruction is executed or until Vcc
is removed. (See Figure 4.) (Note: Chip select must
remain LOW until Vcc reaches its operational value.)
The write all (WRALL) instruction programs all registers with
the data pattern specified in the instruction. As with the
WRITE instruction, the falling edge of CS must occur to
initiate the self-timed programming cycle. If CS is then
brought HIGH after a minimum wait of 200 ns (t
CS
), the D
OUT
pin indicates the READY/BUSY status of the chip (see
Figure 6). Vcc is required to be above 4.5V for WRALL to
function properly.
Write Disable (WDS)
The write disable (WDS) instruction disables all programming
capabilities. This protects the entire device against acci-
dental modification of data until a WEN instruction is
executed. (When Vcc is applied, this part powers up in the
write disabled state.) To protect data, a WDS instruction
should be executed upon completion of each programming
operation.
Write (WRITE)
The WRITE instruction includes 8 or 16 bits of data to be
written into the specified register. After the last data bit
has been applied to D
IN
, and before the next rising edge
of SK, CS must be brought LOW. If the device is write-
enabled, then the falling edge of CS initiates the self-
timed programming cycle (see WEN).
If CS is brought HIGH, after a minimum wait of 200 ns (5V
operation) after the falling edge of CS (t
CS
) D
OUT
will
indicate the READY/BUSY status of the chip. Logical “0”
means programming is still in progress; logical “1” means
the selected register has been written, and the part is
ready for another instruction (see Figure 5). The READY/
BUSY
status will not be available if: a) The CS input goes
HIGH after the end of the self-timed programming cycle,
t
WP
; or b) Simultaneously CS is HIGH, Din is HIGH, and
SK goes HIGH, which clears the status flag.
Erase Register (ERASE)
After the erase instruction is entered, CS must be brought
LOW. The falling edge of CS initiates the self-timed internal
programming cycle. Bringing CS HIGH after a minimum of
t
CS
, will cause D
OUT
to indicate the READ/BUSY status of the
chip: a logical “0” indicates programming is still in progress;
a logical “1” indicates the erase cycle is complete and the
part is ready for another instruction (see Figure 8).
Erase All (ERAL)
Full chip erase is provided for ease of programming. Erasing
the entire chip involves setting all bits in the entire memory
array to a logical “1” (see Figure 9). Vcc is required to be
above 4.5V for ERALL to function properly.
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. 00F
05/26/05
3
IS93C76A
IS93C86A
ISSI
8-bit Organization
(ORG = GND)
Address
(1)
Input Data
x(A
9
-A
0
)
11x xxxx xxxx
x(A
9
-A
0
)
01x xxxx xxxx
00x xxxx xxxx
x(A
9
-A
0
)
10x xxxx xxxx
—
—
(D
7
-D
0
)
(D
7
-D
0
)
—
—
—
®
INSTRUCTION SET - IS93C76A (8kb)
16-bit Organization
(ORG = Vcc)
Address
(1)
Input Data
x(A
8
-A
0
)
11 xxxx xxxx
x(A
8
-A
0
)
01 xxxx xxxx
00 xxxx xxxx
x(A
8
-A
0
)
10 xxxx xxxx
—
—
(D
15
-D
0
)
(D
15
-D
0
)
—
—
—
Instruction
(2)
READ
WEN
(Write Enable)
WRITE
Start Bit OP Code
1
1
1
1
1
1
1
10
00
01
00
00
11
00
WRALL
(Write All Registers)
WDS
(Write Disable)
ERASE
ERAL (
Erase All Registers)
Notes:
1. x = Don't care bit.
2. If the number of bits clocked-in does not match the number corresponding to a selected command, all extra trailing bits are ignored,
and WRITE, WRALL, ERASE, ERAL, WEN, and WDS instructions are rejected, but READ is accepted.
INSTRUCTION SET - IS93C86A (16kb)
8-bit Organization
(ORG = GND)
Address
(1)
Input Data
(A
10
-A
0
)
11x xxxx xxxx
(A
10
-A
0
)
01x xxxx xxxx
00x xxxx xxxx
(A
10
-A
0
)
10x xxxx xxxx
—
—
(D
7
-D
0
)
(D
7
-D
0
)
—
—
—
16-bit Organization
(ORG = Vcc)
Address
(1)
Input Data
(A
9
-A
0
)
11 xxxx xxxx
(A
9
-A
0
)
01 xxxx xxxx
00 xxxx xxxx
(A
9
-A
0
)
10 xxxx xxxx
—
—
(D
15
-D
0
)
(D
15
-D
0
)
—
—
—
Instruction
(2)
READ
WEN
(Write Enable)
WRITE
Start Bit OP Code
1
1
1
1
1
1
1
10
00
01
00
00
11
00
WRALL
(Write All Registers)
WDS
(Write Disable)
ERASE
ERAL (
Erase All Registers)
Notes:
1. x = Don't care bit.
2. If the number of bits clocked-in does not match the number corresponding to a selected command, all extra trailing bits are ignored,
and WRITE, WRALL, ERASE, ERAL, WEN, and WDS instructions are rejected, but READ is accepted.
4
Integrated Silicon Solution, Inc. — www.issi.com —
1-800-379-4774
Rev. 00F
05/26/05
IS93C76A
IS93C86A
ISSI
Value
–0.5 to +6.5
–0.5 to Vcc + 0.5
–55 to +125
–65 to +150
5
Unit
V
V
°C
°C
mA
®
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
V
S
V
P
T
BIAS
T
STG
I
OUT
Parameter
Supply Voltage
Voltage on Any Pin
Temperature Under Bias
Storage Temperature
Output Current
Notes:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
OPERATING RANGE
Range
Industrial
Automotive
Ambient Temperature
–40°C to +85°C
–40°C to +125°C
V
CC
1.8V to 5.5V or 2.5V to 5.5V
2.5V to 5.5V
CAPACITANCE
Symbol
C
IN
C
OUT
Parameter
Input Capacitance
Output Capacitance
Conditions
V
IN
= 0V
V
OUT
= 0V
Max.
5
5
Unit
pF
pF
Integrated Silicon Solution, Inc. — www.issi.com —
See Figure 1, Foxit Reader. Click the Add Bookmark button on the upper left to add a bookmark. This shows that this Foxit Reader can add bookmarks.See Figure 2, another PDF file, the same Foxit Reader...
I used AD9 to create a new PCB and place pads, and this is the result. No matter how I click on the holes, they are all gray. I can't set any parameters. The holes are gray, and no matter how I modify...
Inspired by the ten great pieces of advice from an old engineer, here is a short story:There were two monks living next door to each other; the so-called next door is: the next mountain. They lived in...
[i=s]This post was last edited by UUC on 2020-5-23 17:09[/i]Help: Electronic version of Tongji University's Advanced Mathematics, Volumes 1 and 2, no limit on editions. If anyone has the resources, co...
RT! ~Let's talk about specific applications and cases! ~This real-time series doesn't seem to be used very often? Or is it mainly used in the military industry?...
Abstract:
With the increasing complexity of smart vehicle electrical and electronic architectures, the full lifecycle management of vehicle electronic control components faces multiple challe...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
Introduction to the principles of speech recognition technology
Automatic speech recognition (ASR) technology aims to enable computers to understand human speech and extract the textual inform...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Tiantai Robot's official Weibo account announced on the evening of August 20 that Tiantai Robot Co., Ltd., together with strategic partners including Shandong Future Robot Technology Co., Ltd., Sha...[Details]
We often hear about the precautions for using pure electric vehicles in winter, and many owners even develop relevant strategies, such as adopting a "charge as you go" principle for their vehicles,...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
Electric vehicles are composed of three main components: electric motors, electric motors, and electric vehicles. Maintenance is much simpler than for gasoline-powered vehicles. Maintenance for ele...[Details]
Common Mode Semiconductor has officially launched the GM6503 series—a 5 V, 3 A synchronous step-down DC/DC power module designed for optical communications, servers, industrial applications, and FP...[Details]
Renesas Electronics' new ultra-low-power RA4C1 MCU features advanced security and a dedicated peripheral set, making it ideal for metering and other applications.
The new product mee...[Details]
High-definition media consumption is experiencing a dual growth: an increase in the number of consumers and a transition to higher-definition content. This growth is driven by increasingly widespre...[Details]
On August 18th, China's largest expressway
charging station,
the G25 Changshen Expressway Tonglu Service Area (South Area), officially opened and launched its integrated solar-storage-charg...[Details]
With the continuous development of ultrasonic technology, ultrasound has been widely used in fields such as inspection, cleaning, welding, and medical treatment, and has even found its way into tex...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
